Bump hekate to v6.2.2 and Nyx to v1.6.4

Tiny power save.

.gitignore

@@ -2,3 +2,9 @@
 .vscode
 build/*
 output/*
+loader/payload_00.h
+loader/payload_01.h
+tools/bin2c/bin2c
+tools/bin2c/bin2c.exe
+tools/lz/lz77
+tools/lz/lz77.exe

Makefile

@@ -16,21 +16,26 @@ TARGET := hekate
 BUILDDIR := build
 OUTPUTDIR := output
 SOURCEDIR = bootloader
-VPATH = $(dir $(wildcard ./$(SOURCEDIR)/*/)) $(dir $(wildcard ./$(SOURCEDIR)/*/*/))
+BDKDIR := bdk
+BDKINC := -I./$(BDKDIR)
+VPATH = $(dir ./$(SOURCEDIR)/) $(dir $(wildcard ./$(SOURCEDIR)/*/)) $(dir $(wildcard ./$(SOURCEDIR)/*/*/))
+VPATH += $(dir $(wildcard ./$(BDKDIR)/)) $(dir $(wildcard ./$(BDKDIR)/*/)) $(dir $(wildcard ./$(BDKDIR)/*/*/))
 
 # Main and graphics.
 OBJS = $(addprefix $(BUILDDIR)/$(TARGET)/, \
-	start.o \
+	start.o exception_handlers.o \
 	main.o heap.o \
-	gfx.o tui.o \
-	fe_emmc_tools.o fe_info.o fe_tools.o \
+	gfx.o logos.o tui.o \
+	l4t.o fe_info.o fe_tools.o \
 )
 
 # Hardware.
 OBJS += $(addprefix $(BUILDDIR)/$(TARGET)/, \
-	bpmp.o clock.o cluster.o di.o gpio.o i2c.o mc.o sdram.o pinmux.o se.o smmu.o tsec.o uart.o \
-	fuse.o kfuse.o minerva.o \
-	sdmmc.o sdmmc_driver.o emummc.o nx_emmc.o \
+	bpmp.o ccplex.o clock.o di.o i2c.o irq.o timer.o \
+	mc.o sdram.o minerva.o \
+	gpio.o pinmux.o pmc.o se.o smmu.o tsec.o uart.o \
+	fuse.o kfuse.o \
+	sdmmc.o sdmmc_driver.o emmc.o sd.o emummc.o \
 	bq24193.o max17050.o max7762x.o max77620-rtc.o \
 	hw_init.o \
 )
@@ -43,67 +48,114 @@ OBJS += $(addprefix $(BUILDDIR)/$(TARGET)/, \
 
 # Horizon.
 OBJS += $(addprefix $(BUILDDIR)/$(TARGET)/, \
-	hos.o hos_config.o pkg1.o pkg2.o pkg2_ini_kippatch.o fss.o secmon_exo.o sept.o \
+	hos.o hos_config.o pkg1.o pkg2.o pkg2_ini_kippatch.o fss.o secmon_exo.o \
 )
 
 # Libraries.
 OBJS += $(addprefix $(BUILDDIR)/$(TARGET)/, \
-	lz.o blz.o \
+	lz.o lz4.o blz.o \
 	diskio.o ff.o ffunicode.o ffsystem.o \
 	elfload.o elfreloc_arm.o \
 )
 
+GFX_INC   := '"../$(SOURCEDIR)/gfx/gfx.h"'
+FFCFG_INC := '"../$(SOURCEDIR)/libs/fatfs/ffconf.h"'
+
 ################################################################################
 
 CUSTOMDEFINES := -DIPL_LOAD_ADDR=$(IPL_LOAD_ADDR) -DBL_MAGIC=$(IPL_MAGIC)
-CUSTOMDEFINES += -DBL_VER_MJ=$(BLVERSION_MAJOR) -DBL_VER_MN=$(BLVERSION_MINOR) -DBL_VER_HF=$(BLVERSION_HOTFX) -DBL_RESERVED=$(BLVERSION_RSVD)
-CUSTOMDEFINES += -DNYX_VER_MJ=$(NYXVERSION_MAJOR) -DNYX_VER_MN=$(NYXVERSION_MINOR) -DNYX_VER_HF=$(NYXVERSION_HOTFX) -DNYX_RESERVED=$(NYXVERSION_RSVD)
-#CUSTOMDEFINES += -DMENU_LOGO_ENABLE
+CUSTOMDEFINES += -DBL_VER_MJ=$(BLVERSION_MAJOR) -DBL_VER_MN=$(BLVERSION_MINOR) -DBL_VER_HF=$(BLVERSION_HOTFX) -DBL_VER_RL=$(BLVERSION_REL)
+CUSTOMDEFINES += -DNYX_VER_MJ=$(NYXVERSION_MAJOR) -DNYX_VER_MN=$(NYXVERSION_MINOR) -DNYX_VER_HF=$(NYXVERSION_HOTFX) -DNYX_VER_RL=$(NYXVERSION_REL)
 
-# 0: UART_A, 1: UART_B.
-#CUSTOMDEFINES += -DDEBUG_UART_PORT=0
+# BDK defines.
+CUSTOMDEFINES += -DBDK_MALLOC_NO_DEFRAG -DBDK_MC_ENABLE_AHB_REDIRECT -DBDK_EMUMMC_ENABLE
+CUSTOMDEFINES += -DBDK_WATCHDOG_FIQ_ENABLE -DBDK_RESTART_BL_ON_WDT
+CUSTOMDEFINES += -DGFX_INC=$(GFX_INC) -DFFCFG_INC=$(FFCFG_INC)
 
 #CUSTOMDEFINES += -DDEBUG
 
+# UART Logging: Max baudrate 12.5M.
+# DEBUG_UART_PORT - 0: UART_A, 1: UART_B, 2: UART_C.
+#CUSTOMDEFINES += -DDEBUG_UART_BAUDRATE=115200 -DDEBUG_UART_INVERT=0 -DDEBUG_UART_PORT=0
+
+#TODO: Considering reinstating some of these when pointer warnings have been fixed.
+WARNINGS := -Wall -Wsign-compare -Wno-array-bounds -Wno-stringop-overread -Wno-stringop-overflow
+#-fno-delete-null-pointer-checks
+#-Wstack-usage=byte-size -fstack-usage
+
 ARCH := -march=armv4t -mtune=arm7tdmi -mthumb -mthumb-interwork
-CFLAGS = $(ARCH) -O2 -nostdlib -ffunction-sections -fdata-sections -fomit-frame-pointer -fno-inline -std=gnu11 -Wall $(CUSTOMDEFINES)
+CFLAGS = $(ARCH) -O2 -g -gdwarf-4 -nostdlib -ffunction-sections -fdata-sections -fomit-frame-pointer -fno-inline -std=gnu11 $(WARNINGS) $(CUSTOMDEFINES)
 LDFLAGS = $(ARCH) -nostartfiles -lgcc -Wl,--nmagic,--gc-sections -Xlinker --defsym=IPL_LOAD_ADDR=$(IPL_LOAD_ADDR)
 
 MODULEDIRS := $(wildcard modules/*)
 NYXDIR := $(wildcard nyx)
+LDRDIR := $(wildcard loader)
+TOOLSLZ := $(wildcard tools/lz)
+TOOLSB2C := $(wildcard tools/bin2c)
+TOOLS := $(TOOLSLZ) $(TOOLSB2C)
 
 ################################################################################
 
-.PHONY: all clean $(MODULEDIRS) $(NYXDIR)
+.PHONY: all clean $(MODULEDIRS) $(NYXDIR) $(LDRDIR) $(TOOLS)
 
-all: $(TARGET).bin
-	@echo -n "Payload size is "
-	@wc -c < $(OUTPUTDIR)/$(TARGET).bin
-	@echo "Max size is 126296 Bytes."
+all: $(TARGET).bin $(LDRDIR)
+	@printf ICTC49 >> $(OUTPUTDIR)/$(TARGET).bin
+	@echo "--------------------------------------"
+	@echo -n "Uncompr size: "
+	$(eval BIN_SIZE = $(shell wc -c < $(OUTPUTDIR)/$(TARGET)_unc.bin))
+	@echo $(BIN_SIZE)" Bytes"
+	@echo "Uncompr Max:  140288 Bytes + 3 KiB BSS"
+	@if [ ${BIN_SIZE} -gt 140288 ]; then echo "\e[1;33mUncompr size exceeds limit!\e[0m"; fi
+	@echo -n "Payload size: "
+	$(eval BIN_SIZE = $(shell wc -c < $(OUTPUTDIR)/$(TARGET).bin))
+	@echo $(BIN_SIZE)" Bytes"
+	@echo "Payload Max:  126296 Bytes"
+	@if [ ${BIN_SIZE} -gt 126296 ]; then echo "\e[1;33mPayload size exceeds limit!\e[0m"; fi
+	@echo "--------------------------------------"
 
-clean:
+clean: $(TOOLS)
 	@rm -rf $(OBJS)
 	@rm -rf $(BUILDDIR)
 	@rm -rf $(OUTPUTDIR)
 
 $(MODULEDIRS):
-	$(MAKE) -C $@ $(MAKECMDGOALS) -$(MAKEFLAGS)
+	@$(MAKE) --no-print-directory -C $@ $(MAKECMDGOALS) -$(MAKEFLAGS)
 
 $(NYXDIR):
-	$(MAKE) -C $@ $(MAKECMDGOALS) -$(MAKEFLAGS)
+	@$(MAKE) --no-print-directory -C $@ $(MAKECMDGOALS) -$(MAKEFLAGS)
 
-$(TARGET).bin: $(BUILDDIR)/$(TARGET)/$(TARGET).elf $(MODULEDIRS) $(NYXDIR)
+$(LDRDIR): $(TARGET).bin
+	@$(TOOLSLZ)/lz77 $(OUTPUTDIR)/$(TARGET).bin
+	mv $(OUTPUTDIR)/$(TARGET).bin $(OUTPUTDIR)/$(TARGET)_unc.bin
+	@mv $(OUTPUTDIR)/$(TARGET).bin.00.lz payload_00
+	@mv $(OUTPUTDIR)/$(TARGET).bin.01.lz payload_01
+	@$(TOOLSB2C)/bin2c payload_00 > $(LDRDIR)/payload_00.h
+	@$(TOOLSB2C)/bin2c payload_01 > $(LDRDIR)/payload_01.h
+	@rm payload_00
+	@rm payload_01
+	@$(MAKE) --no-print-directory -C $@ $(MAKECMDGOALS) -$(MAKEFLAGS) PAYLOAD_NAME=$(TARGET)
+
+$(TOOLS):
+	@$(MAKE) --no-print-directory -C $@ $(MAKECMDGOALS) -$(MAKEFLAGS)
+
+$(TARGET).bin: $(BUILDDIR)/$(TARGET)/$(TARGET).elf $(MODULEDIRS) $(NYXDIR) $(TOOLS)
 	$(OBJCOPY) -S -O binary $< $(OUTPUTDIR)/$@
-	@printf ICTC49 >> $(OUTPUTDIR)/$@
 
 $(BUILDDIR)/$(TARGET)/$(TARGET).elf: $(OBJS)
-	$(CC) $(LDFLAGS) -T $(SOURCEDIR)/link.ld $^ -o $@
+	@$(CC) $(LDFLAGS) -T $(SOURCEDIR)/link.ld $^ -o $@
+	@echo "hekate was built with the following flags:\nCFLAGS:  "$(CFLAGS)"\nLDFLAGS: "$(LDFLAGS)
 
 $(BUILDDIR)/$(TARGET)/%.o: %.c
-	$(CC) $(CFLAGS) -c $< -o $@
+	@echo Building $@
+	@$(CC) $(CFLAGS) $(BDKINC) -c $< -o $@
 
 $(BUILDDIR)/$(TARGET)/%.o: %.S
+	@echo Building $@
+	@$(CC) $(CFLAGS) -c $< -o $@
+
+$(OBJS): $(BUILDDIR)/$(TARGET)
+
+$(BUILDDIR)/$(TARGET):
 	@mkdir -p "$(BUILDDIR)"
 	@mkdir -p "$(BUILDDIR)/$(TARGET)"
 	@mkdir -p "$(OUTPUTDIR)"
-	$(CC) $(CFLAGS) -c $< -o $@

README.md

@@ -1,9 +1,38 @@
-# hekate - CTCaer mod
+# hekate - Nyx
 
 ![Image of Hekate](https://user-images.githubusercontent.com/3665130/60391760-bc1e8c00-9afe-11e9-8b7a-b065873081b2.png)
 
 
-Custom Nintendo Switch bootloader, firmware patcher, and more.
+Custom Graphical Nintendo Switch bootloader, firmware patcher, tools, and many more.
+
+
+
+- [Features](#features)
+- [Bootloader folders and files](#bootloader-folders-and-files)
+- [Bootloader configuration](#bootloader-configuration)
+  * [hekate global Configuration keys/values](#hekate-global-configuration-keysvalues-when-entry-is-config)
+  * [Boot entry key/value combinations](#boot-entry-keyvalue-combinations)
+  * [Boot entry key/value combinations for Exosphère](#boot-entry-keyvalue-combinations-for-exosphère)
+  * [Payload storage](#payload-storage)
+  * [Nyx Configuration keys/values](#nyx-configuration-keysvalues-nyxini)
+
+
+
+## Features
+
+- **Fully Configurable and Graphical** with Touchscreen and Joycon input support
+- **Launcher Style, Background and Color Themes**
+- **HOS (Switch OS) Bootloader** -- For CFW Sys/Emu, OFW Sys and Stock Sys
+- **Android & Linux Bootloader**
+- **Payload Launcher**
+- **eMMC/emuMMC Backup/Restore Tools**
+- **SD Card Partition Manager** -- Prepares and formats SD Card for any combo of HOS (Sys/emuMMC), Android and Linux
+- **emuMMC Creation & Manager** -- Can also migrate and fix existing emuMMC
+- **Switch Android & Linux flasher**
+- **USB Mass Storage (UMS) for SD/eMMC/emuMMC** -- Converts Switch into a SD Card Reader
+- **USB Gamepad** -- Converts Switch with Joycon into a USB HID Gamepad
+- **Hardware and Peripherals info** (SoC, Fuses, RAM, Display, Touch, eMMC, SD, Battery, PSU, Charger)
+- **Many other tools** like Archive Bit Fixer, Touch Calibration, SD/eMMC Benchmark, AutoRCM enabler and more
 
 
 ## Bootloader folders and files
@@ -11,28 +40,27 @@ Custom Nintendo Switch bootloader, firmware patcher, and more.
 | Folder/File              | Description                                                           |
 | ------------------------ | --------------------------------------------------------------------- |
 | bootloader               | Main folder.                                                          |
-|  \|__ bootlogo.bmp       | It is used when custom is on and no logopath found. Can be skipped.   |
-|  \|__ hekate_ipl.ini     | Main bootloader configuration and boot entries.                       |
+|  \|__ bootlogo.bmp       | It is used if no `logopath` key is found. User provided. Can be skipped. |
+|  \|__ hekate_ipl.ini     | Main bootloader configuration and boot entries in `Launch` menu.      |
+|  \|__ nyx.ini            | Nyx GUI configuration                                                 |
 |  \|__ patches.ini        | Add external patches. Can be skipped. A template can be found [here](./res/patches_template.ini) |
-|  \|__ update.bin         | If newer, it is loaded at boot. For modchips. Auto updated. Can be skipped. |
-| bootloader/ini/          | For individual inis. 'More configs...' menu. Autoboot is supported.   |
+|  \|__ update.bin         | If newer, it is loaded at boot. Normally for modchips. Auto updated and created at first boot. |
+| bootloader/ini/          | For individual inis. `More configs` menu. Autoboot is supported.   |
 | bootloader/res/          | Nyx user resources. Icons and more.                                   |
-|  \|__ background.bmp     | Nyx - custom background.                                              |
+|  \|__ background.bmp     | Nyx - Custom background. User provided.                               |
 |  \|__ icon_switch.bmp    | Nyx - Default icon for CFWs.                                          |
 |  \|__ icon_payload.bmp   | Nyx - Default icon for Payloads.                                      |
-|  \|__ icon_lakka.bmp     | Nyx - Default icon for Lakka.                                         |
-| bootloader/sys/          | For system modules.                                                   |
-|  \|__ emummc.kipm        | emuMMC KIP1 module. Important!                                        |
+| bootloader/sys/          | hekate and Nyx system modules folder.                                 |
+|  \|__ emummc.kipm        | emuMMC KIP1 module. !Important!                                       |
 |  \|__ libsys_lp0.bso     | LP0 (sleep mode) module. Important!                                   |
-|  \|__ libsys_minerva.bso | Minerva Training Cell. Used for DRAM Frequency training. Important!   |
-|  \|__ nyx.bin            | Nyx - Our GUI. Important!                                             |
-|  \|__ res.pak            | Nyx resources package. Important!                                     |
+|  \|__ libsys_minerva.bso | Minerva Training Cell. Used for DRAM Frequency training. !Important!  |
+|  \|__ nyx.bin            | Nyx - hekate's GUI. !Important!                                       |
+|  \|__ res.pak            | Nyx resources package. !Important!                                    |
+|  \|__ thk.bin            | Atmosphère Tsec Hovi Keygen. !Important!                              |
 | bootloader/screenshots/  | Folder where Nyx screenshots are saved                                |
-| bootloader/payloads/     | For payloads. 'Payloads...' menu. Autoboot only supported by including them into an ini. All CFW bootloaders, tools, Linux payloads are supported. |
-| bootloader/libtools/     | Future reserved                                                       |
-| sept                     | Sept folder. This must be always get updated via the Atmosphère release zip. Needed for tools and booting HOS on 7.0.0 and up. Unused for booting HOS if `fss0=` key is defined. |
+| bootloader/payloads/     | For the `Payloads` menu. All CFW bootloaders, tools, Linux payloads are supported. Autoboot only supported by including them into an ini. |
+| bootloader/libtools/     | Reserved                                                              |
 
-**Note**: Sept files for booting 7.0.0 and up are expected at /sept folder at root of sd card.
 
 
 ## Bootloader configuration
@@ -43,85 +71,143 @@ The bootloader can be configured via 'bootloader/hekate_ipl.ini' (if it is prese
 There are four possible type of entries. "**[ ]**": Boot entry, "**{ }**": Caption, "**#**": Comment, "*newline*": .ini cosmetic newline.
 
 
-You can find a template [Here](./res/hekate_ipl_template.ini)
+**You can find a template [Here](./res/hekate_ipl_template.ini)**
 
 
-### Global Configuration keys/values when boot entry is **config**:
+### hekate Global Configuration keys/values (when entry is *[config]*):
 
 | Config option      | Description                                                |
 | ------------------ | ---------------------------------------------------------- |
 | autoboot=0         | 0: Disable, #: Boot entry number to auto boot.             |
 | autoboot_list=0    | 0: Read `autoboot` boot entry from hekate_ipl.ini, 1: Read from ini folder (ini files are ASCII ordered). |
-| bootwait=3         | 0: Disable (It also disables bootlogo. Having **VOL-** pressed since injection goes to menu.), #: Time to wait for **VOL-** to enter menu. |
-| verification=2     | 0: Disable Backup/Restore verification, 1: Sparse (block based, fast and not 100% reliable), 2: Full (sha256 based, slow and 100% reliable). |
+| bootwait=3         | 0: Disable (It also disables bootlogo. Having **VOL-** pressed since injection goes to menu.), #: Time to wait for **VOL-** to enter menu. Max: 20s. |
+| noticker=0         | 0: Animated line is drawn during custom bootlogo, signifying time left to skip to menu. 1: Disable. |
 | autohosoff=1       | 0: Disable, 1: If woke up from HOS via an RTC alarm, shows logo, then powers off completely, 2: No logo, immediately powers off.|
 | autonogc=1         | 0: Disable, 1: Automatically applies nogc patch if unburnt fuses found and a >= 4.0.0 HOS is booted. |
+| bootprotect=0      | 0: Disable, 1: Protect bootloader folder from being corrupted by disallowing reading or editing in HOS. |
 | updater2p=0        | 0: Disable, 1: Force updates (if needed) the reboot2payload binary to be hekate. |
 | backlight=100      | Screen backlight level. 0-255.                             |
 
 
-### Possible boot entry key/value combinations:
+### Boot entry key/value combinations:
 
 | Config option          | Description                                                |
 | ---------------------- | ---------------------------------------------------------- |
-| warmboot={SD path}     | Replaces the warmboot binary                               |
-| secmon={SD path}       | Replaces the security monitor binary                       |
-| kernel={SD path}       | Replaces the kernel binary                                 |
-| kip1={SD path}         | Replaces/Adds kernel initial process. Multiple can be set. |
-| kip1={SD folder}/*     | Loads every .kip/.kip1 inside a folder. Compatible with single kip1 keys. |
-| fss0={SD path}         | Takes a fusee-secondary binary and `extracts` all needed parts from it. kips, exosphere, warmboot and sept. |
-| kip1patch=patchname    | Enables a kip1 patch. Specify with multiple lines and/or as CSV. If not found, an error will show up |
-| fullsvcperm=1          | Disables SVC verification (full services permission)       |
+| warmboot={FILE path}   | Replaces the warmboot binary                               |
+| secmon={FILE path}     | Replaces the security monitor binary                       |
+| kernel={FILE path}     | Replaces the kernel binary                                 |
+| kip1={FILE path}       | Replaces/Adds kernel initial process. Multiple can be set. |
+| kip1={FOLDER path}/*   | Loads every .kip/.kip1 inside a folder. Compatible with single kip1 keys. |
+| fss0={FILE path}       | Takes an Atmosphere `package3` binary (formerly fusee-secondary.bin) and `extracts` all needed parts from it. kips, exosphere, warmboot and mesophere if enabled. |
+| fss0experimental=1     | Enables loading of experimental content from a FSS0 storage |
+| exofatal={FILE path}   | Replaces the exosphere fatal binary for Mariko             |
+| ---------------------- | ---------------------------------------------------------- |
+| kip1patch=patchname    | Enables a kip1 patch. Specify with multiple lines and/or in one line with `,` as separator. If actual patch is not found, a warning will show up |
+| emupath={FOLDER path}  | Forces emuMMC to use the selected one. (=emuMMC/RAW1, =emuMMC/SD00, etc). emuMMC must be created by hekate because it uses the raw_based/file_based files. |
+| emummcforce=1          | Forces the use of emuMMC. If emummc.ini is disabled or not found, then it causes an error. |
+| emummc_force_disable=1 | Disables emuMMC, if it's enabled.                           |
+| stock=1                | OFW via hekate bootloader. Disables unneeded kernel patching and CFW kips when running stock. `If emuMMC is enabled, emummc_force_disable=1` is required. emuMMC is not supported on stock. If additional KIPs are needed other than OFW's, you can define them with `kip1` key. No kip should be used that relies on Atmosphère patching, because it will hang. If `NOGC` is needed, use `kip1patch=nogc`. |
+| fullsvcperm=1          | Disables SVC verification (full services permission). Doesn't work with Mesosphere as kernel. |
 | debugmode=1            | Enables Debug mode. Obsolete when used with exosphere as secmon. |
-| atmosphere=1           | Enables Atmosphère patching.                               |
-| nouserexceptions=1     | Disables usermode exception handlers when paired with Exosphère. |
-| userpmu=1              | Allows user access to PMU when paired with Exosphère.      |
-| emummc_force_disable=1 | Disabled emuMMC if it's enabled.                           |
-| stock=1                | Disables unneeded kernel patching when running stock or semi-stock. `If emuMMC is enabled, emummc_force_disabled=1` is required to run completely stock. |
-| id=idname              | Identifies boot entry for forced boot via id. Max 7 chars. |
-| payload={SD path}      | Payload launching. Tools, Linux, CFW bootloaders, etc.     |
-| logopath={SD path}     | If no logopath, `bootloader/bootlogo.bmp` will be used if exists. If logopath exists, it will load the specified bitmap. |
-| icon={SD path}         | Force Nyx to use the icon defined here. If this is not found, it will check for a bmp named as the boot entry ([Test 2] -> `bootloader/res/Test 2.bmp`). Otherwise default will be used. |
+| atmosphere=1           | Enables Atmosphère patching. Not needed when `fss0` is used. |
+| ---------------------- | ---------------------------------------------------------- |
+| payload={FILE path}    | Payload launching. Tools, Android/Linux, CFW bootloaders, etc. Any key above when used with that, doesn't get into account. |
+| ---------------------- | ---------------------------------------------------------- |
+| l4t=1                  | L4T Linux/Android native launching.                        |
+| boot_prefixes={FOLDER path} | L4T bootstack directory.                              |
+| ram_oc=0               | L4T RAM Overclocking. Check README_CONFIG.txt for more info. |
+| ram_oc_vdd2=1100       | L4T RAM VDD2 Voltage. Set VDD2 (T210B01) or VDD2/VDDQ (T210) voltage. 1050-1175. |
+| ram_oc_vddq=600        | L4T RAM VDDQ Voltage. Set VDDQ (T210B01). 550-650.         |
+| uart_port=0            | Enables logging on serial port for L4T uboot/kernel.       |
+| Additional keys        | Each distro supports more keys. Check README_CONFIG.txt  for more info. |
+| ---------------------- | ---------------------------------------------------------- |
+| bootwait=3             | Overrides global bootwait from `[config]`.                 |
+| id=IDNAME              | Identifies boot entry for forced boot via id. Max 7 chars. |
+| logopath={FILE path}   | If it exists, it will load the specified bitmap. Otherwise `bootloader/bootlogo.bmp` will be used if exists |
+| icon={FILE path}       | Force Nyx to use the icon defined here. If this is not found, it will check for a bmp named as the boot entry ([Test 2] -> `bootloader/res/Test 2.bmp`). Otherwise defaults will be used. |
+
 
 **Note1**: When using the wildcard (`/*`) with `kip1` you can still use the normal `kip1` after that to load extra single kips.
 
 **Note2**: When using FSS0 it parses exosphere, warmboot and all core kips. You can override the first 2 by using `secmon`/`warmboot` after defining `fss0`.
 You can define `kip1` to load an extra kip or many via the wildcard (`/*`) usage.
 
-**Warning**: Never define *fss0 core* kips when using `fss0` and make sure that the folder (when using `/*`), does not include them.
-This is in case the kips are incompatible between them. If compatible, you can override `fss0` kips with no issues (useful for testing with intermediate kip changes).
+**Warning**: Careful when you define *fss0 core* kips when using `fss0` or the folder (when using `/*`) includes them.
+This is in case the kips are incompatible between them. If compatible, you can override `fss0` kips with no issues (useful for testing with intermediate kip changes). In such cases, the `kip1` line must be under `fss0` line.
+
+
+### Boot entry key/value combinations for Exosphère:
+
+| Config option          | Description                                                |
+| ---------------------- | ---------------------------------------------------------- |
+| nouserexceptions=1     | Disables usermode exception handlers when paired with Exosphère. |
+| userpmu=1              | Enables user access to PMU when paired with Exosphère.     |
+| cal0blank=1            | Overrides Exosphère config `blank_prodinfo_{sys/emu}mmc`. If that key doesn't exist, `exosphere.ini` will be used. |
+| cal0writesys=1         | Overrides Exosphère config `allow_writing_to_cal_sysmmc`. If that key doesn't exist, `exosphere.ini` will be used. |
+| usb3force=1            | Overrides system settings mitm config `usb30_force_enabled`. If that key doesn't exist, `system_settings.ini` will be used. |
+
+
+**Note**: `cal0blank`, `cal0writesys`, `usb3force`, as stated override the `exosphere.ini` or `system_settings.ini`. 0: Disable, 1: Enable, Key Missing: Use original value.
+
+
+**Note2**: `blank_prodinfo_{sys/emu}mmc`, `allow_writing_to_cal_sysmmc` and `usb30_force_enabled` in `exosphere.ini` and `system_settings.ini` respectively, are the only atmosphere config keys that can affect hekate booting configuration externally, **if** the equivalent keys in hekate config are missing.
 
 
 ### Payload storage:
 
 hekate has a boot storage in the binary that helps it configure it outside of BPMP enviroment:
 
-| Offset / Name        | Description                                                       |
-| -------------------- | ----------------------------------------------------------------- |
-| '0x94' boot_cfg      | bit0: Force AutoBoot, bit1: Show launch log, bit2: Boot from ID, bit7: sept run. |
-| '0x95' autoboot      | If `Force AutoBoot`: 0: Force go to menu, else boot that entry.   |
-| '0x96' autoboot_list | If `Force AutoBoot` and `autoboot` then it boots from ini folder. |
-| '0x97' extra_cfg     | bit7: Force Nyx to run `Dump pkg1/2`.                             |
-| '0x98' id[8]         | When Boot from ID is set, it will search all inis automatically and find the boot entry with that id and boot it. Must be NULL terminated. |
-| '0x98' xt_str[128]   | Depends on the set cfg bits.                                      |
+| Offset / Name           | Description                                                       |
+| ----------------------- | ----------------------------------------------------------------- |
+| '0x94' boot_cfg         | bit0: `Force AutoBoot`, bit1: `Show launch log`, bit2: `Boot from ID`, bit3: `Boot to emuMMC`. |
+| '0x95' autoboot         | If `Force AutoBoot`, 0: Force go to menu, else boot that entry.   |
+| '0x96' autoboot_list    | If `Force AutoBoot` and `autoboot` then it boots from ini folder. |
+| '0x97' extra_cfg        | When menu is forced: bit5: `Run UMS`.                             |
+| '0x98' xt_str[128]      | Depends on the set cfg bits.                                      |
+| '0x98' ums[1]           | When `Run UMS` is set, it will launch the selected UMS. 0: SD, 1: eMMC BOOT0, 2: eMMC BOOT1, 3: eMMC GPP, 4: emuMMC BOOT0, 5: emuMMC BOOT1, 6: emuMMC GPP,  |
+| '0x98' id[8]            | When `Boot from ID` is set, it will search all inis automatically and find the boot entry with that id and boot it. Must be NULL terminated. |
+| '0xA0' emummc_path[120] | When `Boot to emuMMC` is set, it will override the current emuMMC (boot entry or emummc.ini). Must be NULL terminated. |
 
 
-If the main .ini is not found, it is created on the first hekate boot.
+### Nyx Configuration keys/values (nyx.ini):
+
+| Config option      | Description                                                |
+| ------------------ | ---------------------------------------------------------- |
+| themebg=2d2d2d     | Sets Nyx background color in HEX. EXPERIMENTAL.            |
+| themecolor=167     | Sets Nyx color of text highlights.                         |
+| entries5col=0      | 1: Sets Launch entry columns from 4 to 5 per line. For a total of 10 entries. |
+| timeoff=100        | Sets time offset in HEX. Must be in HOS epoch format       |
+| homescreen=0       | Sets home screen. 0: Home menu, 1: All configs (merges Launch and More configs), 2: Launch, 3: More Configs. |
+| verification=1     | 0: Disable Backup/Restore verification, 1: Sparse (block based, fast and mostly reliable), 2: Full (sha256 based, slow and 100% reliable). |
+| ------------------ | ------- The following options can only be edited in nyx.ini ------- |
+| umsemmcrw=0        | 1: eMMC/emuMMC UMS will be mounted as writable by default. |
+| jcdisable=0        | 1: Disables Joycon driver completely.                      |
+| jcforceright=0     | 1: Forces right joycon to be used as main mouse control.   |
+| bpmpclock=1        | 0: Auto, 1: Fastest, 2: Faster, 3: Fast. Use 2 or 3 if Nyx hangs or some functions like UMS/Backup Verification fail. |
 
 
 ```
-hekate     (C) 2018 naehrwert, st4rk
-CTCaer mod (C) 2018 CTCaer.
+hekate  (c) 2018,      naehrwert, st4rk.
+        (c) 2018-2024, CTCaer.
+
+Nyx GUI (c) 2019-2024, CTCaer.
 
 Thanks to: derrek, nedwill, plutoo, shuffle2, smea, thexyz, yellows8.
 Greetings to: fincs, hexkyz, SciresM, Shiny Quagsire, WinterMute.
 
 Open source and free packages used:
- - FatFs R0.13a, Copyright (C) 2017, ChaN
- - bcl-1.2.0, Copyright (C) 2003-2006, Marcus Geelnard
- - Atmosphère (Exosphere types/panic, prc id kernel patches),
-   Copyright (C) 2018-2019, Atmosphère-NX
- - elfload, Copyright (C) 2014 Owen Shepherd, Copyright (C) 2018 M4xw
+ - Littlev Graphics Library,
+   Copyright (c) 2016-2018 Gabor Kiss-Vamosi
+ - FatFs R0.13c,
+   Copyright (c) 2006-2018, ChaN
+   Copyright (c) 2018-2022, CTCaer
+ - bcl-1.2.0,
+   Copyright (c) 2003-2006, Marcus Geelnard
+ - blz,
+   Copyright (c) 2018, SciresM
+ - elfload,
+   Copyright (c) 2014 Owen Shepherd,
+   Copyright (c) 2018 M4xw
 
                          ___
                       .-'   `'.

README_BOOTLOGO.md

@@ -4,13 +4,16 @@ The bootlogo can be any size with a maximum of 720 x 1280.
 
 When it's smaller than 720 x 1280, it is automatically centered and the background takes the color of the first pixel.
 
-When saving a landscape bootlogo, it should be rotated 90 degrees counterclockwise.
+The process is to create a landscape bootlogo and then rotate it 90 degrees counterclockwise.
 
 Lastly, the supported format is 32-bit (ARGB) BMP. Classic 24-bit (RGB) BMPs are not supported for performance reasons.
 
 
 ## How to configure
 
-If the custom logo option is enabled, it will try to load /bootlogo.bmp. If this is not found, the default hekate's logo will be used.
+If a boot entry specifies a custom logo path (`logopath=`), this one will be loaded.
 
-If a boot entry specifies a custom logo path, this is one will be loaded. Again if this is not found, bootlogo.bmp will be loaded and if that fails, hekate's built-in will be used.
+If the above is not found or the format is not correct, it will try to load `bootloader/bootlogo.bmp`.
+If this is not found, the default hekate logo will be used.
+
+(`bootloader/bootlogo.bmp` is basically like a global bootlogo.)

Versions.inc

@@ -1,11 +1,11 @@
 # IPL Version.
-BLVERSION_MAJOR := 5
-BLVERSION_MINOR := 1
+BLVERSION_MAJOR := 6
+BLVERSION_MINOR := 2
 BLVERSION_HOTFX := 2
-BLVERSION_RSVD := 0
+BLVERSION_REL   := 0
 
 # Nyx Version.
-NYXVERSION_MAJOR := 0
-NYXVERSION_MINOR := 8
-NYXVERSION_HOTFX := 5
-NYXVERSION_RSVD := 0
+NYXVERSION_MAJOR := 1
+NYXVERSION_MINOR := 6
+NYXVERSION_HOTFX := 4
+NYXVERSION_REL   := 0

bdk/bdk.h

@@ -0,0 +1,80 @@
+/*
+ * Copyright (c) 2022 CTCaer
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef BDK_H
+#define BDK_H
+
+#include <memory_map.h>
+
+#include <display/di.h>
+#include <display/vic.h>
+#include <input/als.h>
+#include <input/joycon.h>
+#include <input/touch.h>
+#include <mem/emc.h>
+#include <mem/heap.h>
+#include <mem/mc.h>
+#include <mem/minerva.h>
+#include <mem/sdram.h>
+#include <mem/smmu.h>
+#include <module.h>
+#include <power/bm92t36.h>
+#include <power/bq24193.h>
+#include <power/max17050.h>
+#include <power/max77620.h>
+#include <power/max7762x.h>
+#include <power/max77812.h>
+#include <power/regulator_5v.h>
+#include <rtc/max77620-rtc.h>
+#include <sec/se.h>
+#include <sec/tsec.h>
+#include <soc/actmon.h>
+#include <soc/bpmp.h>
+#include <soc/ccplex.h>
+#include <soc/clock.h>
+#include <soc/fuse.h>
+#include <soc/gpio.h>
+#include <soc/hw_init.h>
+#include <soc/i2c.h>
+#include <soc/irq.h>
+#include <soc/kfuse.h>
+#include <soc/pinmux.h>
+#include <soc/pmc.h>
+#include <soc/timer.h>
+#include <soc/t210.h>
+#include <soc/uart.h>
+#include <storage/emmc.h>
+#include <storage/mbr_gpt.h>
+#include <storage/mmc.h>
+#include <storage/nx_emmc_bis.h>
+#include <storage/ramdisk.h>
+#include <storage/sd.h>
+#include <storage/sdmmc.h>
+#include <thermal/fan.h>
+#include <thermal/tmp451.h>
+#include <usb/usbd.h>
+#include <utils/aarch64_util.h>
+#include <utils/btn.h>
+#include <utils/dirlist.h>
+#include <utils/ini.h>
+#include <utils/list.h>
+#include <utils/sprintf.h>
+#include <utils/types.h>
+#include <utils/util.h>
+
+#include <gfx_utils.h>
+
+#endif

bdk/display/di.h

@@ -0,0 +1,903 @@
+/*
+ * Copyright (c) 2018 naehrwert
+ * Copyright (c) 2018-2024 CTCaer
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef _DI_H_
+#define _DI_H_
+
+#include <memory_map.h>
+#include <utils/types.h>
+
+#define DSI_VIDEO_DISABLED 0
+#define DSI_VIDEO_ENABLED  1
+
+#define WINDOW_A 0
+#define WINDOW_B 1
+#define WINDOW_C 2
+#define WINDOW_D 3
+
+/*! Display registers. */
+#define _DIREG(reg) ((reg) * 4)
+
+// Display controller scratch registers.
+#define DC_D_WINBUF_DD_SCRATCH_REGISTER_0 0xED
+#define DC_D_WINBUF_DD_SCRATCH_REGISTER_1 0xEE
+#define DC_T_WINBUF_TD_SCRATCH_REGISTER_0 0x16D
+#define DC_T_WINBUF_TD_SCRATCH_REGISTER_1 0x16E
+#define DC_COM_SCRATCH_REGISTER_A 0x325
+#define DC_COM_SCRATCH_REGISTER_B 0x326
+#define DC_A_WINBUF_AD_SCRATCH_REGISTER_0 0xBED
+#define DC_A_WINBUF_AD_SCRATCH_REGISTER_1 0xBEE
+#define DC_B_WINBUF_BD_SCRATCH_REGISTER_0 0xDED
+#define DC_B_WINBUF_BD_SCRATCH_REGISTER_1 0xDEE
+#define DC_C_WINBUF_CD_SCRATCH_REGISTER_0 0xFED
+#define DC_C_WINBUF_CD_SCRATCH_REGISTER_1 0xFEE
+
+// DC_CMD non-shadowed command/sync registers.
+#define DC_CMD_GENERAL_INCR_SYNCPT 0x00
+#define  SYNCPT_GENERAL_INDX(x) (((x) & 0xFF) << 0)
+#define  SYNCPT_GENERAL_COND(x) (((x) & 0xFF) << 8)
+#define  COND_REG_WR_SAFE 3
+
+#define DC_CMD_GENERAL_INCR_SYNCPT_CNTRL 0x01
+#define  SYNCPT_CNTRL_SOFT_RESET BIT(0)
+#define  SYNCPT_CNTRL_NO_STALL   BIT(8)
+
+#define DC_CMD_CONT_SYNCPT_VSYNC 0x28
+#define  SYNCPT_VSYNC_INDX(x) (((x) & 0xFF) << 0)
+#define  SYNCPT_VSYNC_ENABLE  BIT(8)
+
+#define DC_CMD_DISPLAY_COMMAND_OPTION0 0x031
+
+#define DC_CMD_DISPLAY_COMMAND 0x32
+#define  DISP_CTRL_MODE_STOP       (0 << 5)
+#define  DISP_CTRL_MODE_C_DISPLAY  (1 << 5)
+#define  DISP_CTRL_MODE_NC_DISPLAY (2 << 5)
+#define  DISP_CTRL_MODE_MASK       (3 << 5)
+
+#define DC_CMD_DISPLAY_POWER_CONTROL 0x36
+#define  PW0_ENABLE BIT(0)
+#define  PW1_ENABLE BIT(2)
+#define  PW2_ENABLE BIT(4)
+#define  PW3_ENABLE BIT(6)
+#define  PW4_ENABLE BIT(8)
+#define  PM0_ENABLE BIT(16)
+#define  PM1_ENABLE BIT(18)
+
+#define DC_CMD_INT_STATUS 0x37
+#define DC_CMD_INT_MASK 0x38
+#define DC_CMD_INT_ENABLE 0x39
+#define  DC_CMD_INT_FRAME_END_INT BIT(1)
+#define  DC_CMD_INT_V_BLANK_INT   BIT(2)
+#define DC_CMD_INT_POLARITY 0x3B
+
+#define DC_CMD_STATE_ACCESS 0x40
+#define  READ_MUX_ASSEMBLY  0x0
+#define  WRITE_MUX_ASSEMBLY 0x0
+#define  READ_MUX_ACTIVE    BIT(0)
+#define  WRITE_MUX_ACTIVE   BIT(2)
+
+#define DC_CMD_STATE_CONTROL 0x41
+#define  GENERAL_ACT_REQ BIT(0)
+#define  WIN_ACT_REQ     1
+#define  WIN_A_ACT_REQ   BIT(1)
+#define  WIN_B_ACT_REQ   BIT(2)
+#define  WIN_C_ACT_REQ   BIT(3)
+#define  WIN_D_ACT_REQ   BIT(4)
+#define  CURSOR_ACT_REQ  BIT(7)
+#define  GENERAL_UPDATE  BIT(8)
+#define  WIN_UPDATE      9
+#define  WIN_A_UPDATE    BIT(9)
+#define  WIN_B_UPDATE    BIT(10)
+#define  WIN_C_UPDATE    BIT(11)
+#define  WIN_D_UPDATE    BIT(12)
+#define  CURSOR_UPDATE   BIT(15)
+#define  NC_HOST_TRIG    BIT(24)
+
+#define DC_CMD_DISPLAY_WINDOW_HEADER 0x42
+#define  WINDOW_SELECT   4
+#define  WINDOW_A_SELECT BIT(4)
+#define  WINDOW_B_SELECT BIT(5)
+#define  WINDOW_C_SELECT BIT(6)
+#define  WINDOW_D_SELECT BIT(7)
+
+#define DC_CMD_REG_ACT_CONTROL 0x43
+#define  GENERAL_ACT_HCNTR_SEL BIT(0)
+#define  WIN_A_ACT_HCNTR_SEL   BIT(2)
+#define  WIN_B_ACT_HCNTR_SEL   BIT(4)
+#define  WIN_C_ACT_HCNTR_SEL   BIT(6)
+#define  CURSOR_ACT_HCNTR_SEL  BIT(7)
+#define  WIN_D_ACT_HCNTR_SEL   BIT(10)
+
+// DC_D_WIN_DD window D instance of DC_WIN
+#define DC_D_WIN_DD_WIN_OPTIONS 0x80
+#define DC_D_WIN_DD_COLOR_DEPTH 0x83
+#define DC_D_WIN_DD_POSITION    0x84
+#define DC_D_WIN_DD_SIZE        0x85
+#define DC_D_WIN_DD_LINE_STRIDE 0x8A
+#define DC_D_WIN_DD_BLEND_LAYER_CONTROL 0x96
+#define DC_D_WIN_DD_BLEND_MATCH_SELECT  0x97
+#define DC_D_WIN_DD_BLEND_ALPHA_1BIT    0x99
+
+// DC_D_WINBUF_DD window D instance of DC_WINBUF
+#define DC_D_WINBUF_DD_START_ADDR    0xC0
+#define DC_D_WINBUF_DD_ADDR_H_OFFSET 0xC6
+#define DC_D_WINBUF_DD_ADDR_V_OFFSET 0xC8
+#define DC_D_WINBUF_DD_START_ADDR_HI 0xCD
+#define DC_D_WINBUF_DD_MEMFETCH_CONTROL 0xEB
+
+// DC_T_WIN_TD macro for using DD defines.
+#define _DC_T(reg) ((reg) + 0x80)
+
+// DC_COM non-shadowed registers.
+#define DC_COM_CRC_CONTROL 0x300
+#define DC_COM_PIN_OUTPUT_ENABLE(x) (0x302 + (x))
+#define DC_COM_PIN_OUTPUT_POLARITY(x) (0x306 + (x))
+#define  LSC0_OUTPUT_POLARITY_LOW BIT(24)
+
+// CMU registers.
+#define DC_COM_CMU_CSC_KRR    0x32A
+#define DC_COM_CMU_CSC_KGR    0x32B
+#define DC_COM_CMU_CSC_KBR    0x32C
+#define DC_COM_CMU_CSC_KRG    0x32D
+#define DC_COM_CMU_CSC_KGG    0x32E
+#define DC_COM_CMU_CSC_KBG    0x32F
+#define DC_COM_CMU_CSC_KRB    0x330
+#define DC_COM_CMU_CSC_KGB    0x331
+#define DC_COM_CMU_CSC_KBB    0x332
+#define DC_COM_CMU_LUT1       0x336
+#define  LUT1_ADDR(x)      ((x) & 0xFF)
+#define  LUT1_DATA(x)      (((x) & 0xFFF) << 16)
+#define  LUT1_READ_DATA(x) (((x) >> 16) & 0xFFF)
+#define DC_COM_CMU_LUT2       0x337
+#define  LUT2_ADDR(x)      ((x) & 0x3FF)
+#define  LUT2_DATA(x)      (((x) & 0xFF) << 16)
+#define  LUT2_READ_DATA(x) (((x) >> 16) & 0xFF)
+#define DC_COM_CMU_LUT1_READ  0x338
+#define  LUT1_READ_ADDR(x) (((x) & 0xFF) << 8)
+#define  LUT1_READ_EN      BIT(0)
+#define DC_COM_CMU_LUT2_READ  0x339
+#define  LUT2_READ_ADDR(x) (((x) & 0x3FF) << 8)
+#define  LUT2_READ_EN      BIT(0)
+
+#define DC_COM_DSC_TOP_CTL 0x33E
+
+// DC_DISP shadowed registers.
+#define DC_DISP_DISP_WIN_OPTIONS 0x402
+#define  CURSOR_ENABLE   BIT(16)
+#define  SOR_ENABLE      BIT(25)
+#define  SOR1_ENABLE     BIT(26)
+#define  SOR1_TIMING_CYA BIT(27)
+#define  DSI_ENABLE      BIT(29)
+#define  HDMI_ENABLE     BIT(30)
+
+
+#define DC_DISP_DISP_MEM_HIGH_PRIORITY 0x403
+#define DC_DISP_DISP_MEM_HIGH_PRIORITY_TIMER 0x404
+
+#define DC_DISP_DISP_TIMING_OPTIONS 0x405
+#define  VSYNC_H_POSITION(x) (((x) & 0x1FFF) << 0)
+
+#define DC_DISP_REF_TO_SYNC 0x406
+#define  H_REF_TO_SYNC(x) (((x) & 0x1FFF) <<  0) // Min 0 pixel clock.
+#define  V_REF_TO_SYNC(x) (((x) & 0x1FFF) << 16) // Min 1 line  clock.
+
+#define DC_DISP_SYNC_WIDTH 0x407
+#define  H_SYNC_WIDTH(x) (((x) & 0x1FFF) <<  0) // Min 1 pixel clock.
+#define  V_SYNC_WIDTH(x) (((x) & 0x1FFF) << 16) // Min 1 line  clock.
+
+#define DC_DISP_BACK_PORCH 0x408
+#define  H_BACK_PORCH(x) (((x) & 0x1FFF) <<  0)
+#define  V_BACK_PORCH(x) (((x) & 0x1FFF) << 16)
+
+#define DC_DISP_ACTIVE 0x409
+#define  H_DISP_ACTIVE(x) (((x) & 0x1FFF) <<  0) // Min 16 pixel clock.
+#define  V_DISP_ACTIVE(x) (((x) & 0x1FFF) << 16) // Min 16 line  clock.
+
+#define DC_DISP_FRONT_PORCH 0x40A
+#define  H_FRONT_PORCH(x) (((x) & 0x1FFF) <<  0) // Min -=PS_=-H_REF_TO_SYNC + 1
+#define  V_FRONT_PORCH(x) (((x) & 0x1FFF) << 16) // Min -=PS_=-V_REF_TO_SYNC + 1
+
+#define DC_DISP_DISP_CLOCK_CONTROL 0x42E
+#define  SHIFT_CLK_DIVIDER(x)    ((x) & 0xFF)
+#define  PIXEL_CLK_DIVIDER_PCD1  (0 << 8)
+#define  PIXEL_CLK_DIVIDER_PCD1H (1 << 8)
+#define  PIXEL_CLK_DIVIDER_PCD2  (2 << 8)
+#define  PIXEL_CLK_DIVIDER_PCD3  (3 << 8)
+#define  PIXEL_CLK_DIVIDER_PCD4  (4 << 8)
+#define  PIXEL_CLK_DIVIDER_PCD6  (5 << 8)
+#define  PIXEL_CLK_DIVIDER_PCD8  (6 << 8)
+#define  PIXEL_CLK_DIVIDER_PCD9  (7 << 8)
+#define  PIXEL_CLK_DIVIDER_PCD12 (8 << 8)
+#define  PIXEL_CLK_DIVIDER_PCD16 (9 << 8)
+#define  PIXEL_CLK_DIVIDER_PCD18 (10 << 8)
+#define  PIXEL_CLK_DIVIDER_PCD24 (11 << 8)
+#define  PIXEL_CLK_DIVIDER_PCD13 (12 << 8)
+
+#define DC_DISP_DISP_INTERFACE_CONTROL 0x42F
+#define  DISP_DATA_FORMAT_DF1P1C    (0 << 0)
+#define  DISP_DATA_FORMAT_DF1P2C24B (1 << 0)
+#define  DISP_DATA_FORMAT_DF1P2C18B (2 << 0)
+#define  DISP_DATA_FORMAT_DF1P2C16B (3 << 0)
+#define  DISP_DATA_FORMAT_DF2S      (4 << 0)
+#define  DISP_DATA_FORMAT_DF3S      (5 << 0)
+#define  DISP_DATA_FORMAT_DFSPI     (6 << 0)
+#define  DISP_DATA_FORMAT_DF1P3C24B (7 << 0)
+#define  DISP_DATA_FORMAT_DF1P3C18B (8 << 0)
+#define  DISP_ALIGNMENT_MSB         (0 << 8)
+#define  DISP_ALIGNMENT_LSB         (1 << 8)
+#define  DISP_ORDER_RED_BLUE        (0 << 9)
+#define  DISP_ORDER_BLUE_RED        (1 << 9)
+
+#define DC_DISP_DISP_COLOR_CONTROL 0x430
+#define  BASE_COLOR_SIZE_MASK   (0xF << 0)
+#define  BASE_COLOR_SIZE_666    (0 << 0)
+#define  BASE_COLOR_SIZE_111    (1 << 0)
+#define  BASE_COLOR_SIZE_222    (2 << 0)
+#define  BASE_COLOR_SIZE_333    (3 << 0)
+#define  BASE_COLOR_SIZE_444    (4 << 0)
+#define  BASE_COLOR_SIZE_555    (5 << 0)
+#define  BASE_COLOR_SIZE_565    (6 << 0)
+#define  BASE_COLOR_SIZE_332    (7 << 0)
+#define  BASE_COLOR_SIZE_888    (8 << 0)
+#define  DITHER_CONTROL_MASK    (3 << 8)
+#define  DITHER_CONTROL_DISABLE (0 << 8)
+#define  DITHER_CONTROL_ORDERED (2 << 8)
+#define  DITHER_CONTROL_ERRDIFF (3 << 8)
+#define  DISP_COLOR_SWAP        BIT(16)
+#define  BLANK_COLOR_WHITE      BIT(17)
+#define  CMU_ENABLE             BIT(20)
+
+#define DC_DISP_SHIFT_CLOCK_OPTIONS 0x431
+#define  SC0_H_QUALIFIER_NONE	BIT(0)
+#define  SC1_H_QUALIFIER_NONE	BIT(16)
+
+#define DC_DISP_DATA_ENABLE_OPTIONS 0x432
+#define  DE_SELECT_ACTIVE_BLANK  (0 << 0)
+#define  DE_SELECT_ACTIVE        (1 << 0)
+#define  DE_SELECT_ACTIVE_IS     (2 << 0)
+#define  DE_CONTROL_ONECLK       (0 << 2)
+#define  DE_CONTROL_NORMAL       (1 << 2)
+#define  DE_CONTROL_EARLY_EXT    (2 << 2)
+#define  DE_CONTROL_EARLY        (3 << 2)
+#define  DE_CONTROL_ACTIVE_BLANK (4 << 2)
+
+// Cursor configuration registers.
+#define DC_DISP_CURSOR_FOREGROUND    0x43C
+#define DC_DISP_CURSOR_BACKGROUND    0x43D
+#define  CURSOR_COLOR(r,g,b) (((r) & 0xFF) | (((g) & 0xFF) << 8) | (((b) & 0xFF) << 16))
+
+#define DC_DISP_CURSOR_START_ADDR    0x43E
+#define DC_DISP_CURSOR_START_ADDR_NS 0x43F
+#define  CURSOR_CLIPPING(w) ((w) << 28)
+#define   CURSOR_CLIP_WIN_A 1
+#define   CURSOR_CLIP_WIN_B 2
+#define   CURSOR_CLIP_WIN_C 3
+#define  CURSOR_SIZE_32  (0 << 24)
+#define  CURSOR_SIZE_64  (1 << 24)
+#define  CURSOR_SIZE_128 (2 << 24)
+#define  CURSOR_SIZE_256 (3 << 24)
+#define DC_DISP_CURSOR_POSITION      0x440
+#define DC_DISP_BLEND_BACKGROUND_COLOR 0x4E4
+#define DC_DISP_CURSOR_START_ADDR_HI 0x4EC
+#define DC_DISP_CURSOR_START_ADDR_HI_NS 0x4ED
+#define DC_DISP_BLEND_CURSOR_CONTROL 0x4F1
+#define  CURSOR_BLEND_2BIT     (0 << 24)
+#define  CURSOR_BLEND_R8G8B8A8 (1 << 24)
+#define  CURSOR_BLEND_SRC_FACTOR(n) ((n) << 8)
+#define  CURSOR_BLEND_DST_FACTOR(n) ((n) << 16)
+#define   CURSOR_BLEND_ZRO 0
+#define   CURSOR_BLEND_K1  1
+#define   CURSOR_BLEND_NK1 2
+// End of cursor cfg regs.
+
+#define DC_DISP_DC_MCCIF_FIFOCTRL 0x480
+#define DC_DISP_SD_BL_PARAMETERS 0x4D7
+#define DC_DISP_SD_BL_CONTROL 0x4DC
+#define DC_DISP_BLEND_BACKGROUND_COLOR 0x4E4
+
+#define DC_WINC_COLOR_PALETTE 0x500
+#define  COLOR_PALETTE_IDX(off) (DC_WINC_COLOR_PALETTE + (off))
+#define  COLOR_PALETTE_RGB(rgb) (byte_swap_32(rgb) >> 8)
+#define DC_WINC_PALETTE_COLOR_EXT 0x600
+
+#define DC_WINC_H_FILTER_P(p) (0x601 + (p))
+#define DC_WINC_V_FILTER_P(p) (0x619 + (p))
+#define DC_WINC_H_FILTER_HI_P(p) (0x629 + (p))
+
+#define DC_WINC_CSC_YOF 0x611
+#define DC_WINC_CSC_KYRGB 0x612
+#define DC_WINC_CSC_KUR 0x613
+#define DC_WINC_CSC_KVR 0x614
+#define DC_WINC_CSC_KUG 0x615
+#define DC_WINC_CSC_KVG 0x616
+#define DC_WINC_CSC_KUB 0x617
+#define DC_WINC_CSC_KVB 0x618
+#define DC_WIN_AD_WIN_OPTIONS 0xB80
+#define DC_WIN_BD_WIN_OPTIONS 0xD80
+#define DC_WIN_CD_WIN_OPTIONS 0xF80
+
+// The following registers are A/B/C shadows of the 0xB80/0xD80/0xF80 registers (see DISPLAY_WINDOW_HEADER).
+#define DC_WIN_WIN_OPTIONS 0x700
+#define  H_DIRECTION          BIT(0)
+#define  V_DIRECTION          BIT(2)
+#define  SCAN_COLUMN          BIT(4)
+#define  COLOR_EXPAND         BIT(6)
+#define  H_FILTER_ENABLE      BIT(8)
+#define  V_FILTER_ENABLE      BIT(10)
+#define  COLOR_PALETTE_ENABLE BIT(16)
+#define  CSC_ENABLE           BIT(18)
+#define  DV_ENABLE            BIT(20)
+#define  WIN_ENABLE           BIT(30)
+#define  H_FILTER_EXPAND      BIT(31)
+
+#define DC_WIN_BUFFER_CONTROL 0x702
+#define  BUFFER_CONTROL_HOST  0
+#define  BUFFER_CONTROL_VI    1
+#define  BUFFER_CONTROL_SB2D  4
+
+#define DC_WIN_COLOR_DEPTH 0x703
+#define  WIN_COLOR_DEPTH_P1             0x0
+#define  WIN_COLOR_DEPTH_P2             0x1
+#define  WIN_COLOR_DEPTH_P4             0x2
+#define  WIN_COLOR_DEPTH_P8             0x3
+#define  WIN_COLOR_DEPTH_B4G4R4A4       0x4
+#define  WIN_COLOR_DEPTH_B5G5R5A        0x5
+#define  WIN_COLOR_DEPTH_B5G6R5         0x6
+#define  WIN_COLOR_DEPTH_AB5G5R5        0x7
+#define  WIN_COLOR_DEPTH_B8G8R8A8       0xC
+#define  WIN_COLOR_DEPTH_R8G8B8A8       0xD
+#define  WIN_COLOR_DEPTH_B6x2G6x2R6x2A8 0xE
+#define  WIN_COLOR_DEPTH_R6x2G6x2B6x2A8 0xF
+#define  WIN_COLOR_DEPTH_YCbCr422       0x10
+#define  WIN_COLOR_DEPTH_YUV422         0x11
+#define  WIN_COLOR_DEPTH_YCbCr420P      0x12
+#define  WIN_COLOR_DEPTH_YUV420P        0x13
+#define  WIN_COLOR_DEPTH_YCbCr422P      0x14
+#define  WIN_COLOR_DEPTH_YUV422P        0x15
+#define  WIN_COLOR_DEPTH_YCbCr422R      0x16
+#define  WIN_COLOR_DEPTH_YUV422R        0x17
+#define  WIN_COLOR_DEPTH_YCbCr422RA     0x18
+#define  WIN_COLOR_DEPTH_YUV422RA       0x19
+#define  WIN_COLOR_DEPTH_X1R5G5B5       0x1E
+#define  WIN_COLOR_DEPTH_R5G5B5X1       0x1F
+#define  WIN_COLOR_DEPTH_X1B5G5R5       0x20
+#define  WIN_COLOR_DEPTH_B5G5R5X1       0x21
+#define  WIN_COLOR_DEPTH_YCbCr444P      0x29
+#define  WIN_COLOR_DEPTH_YCrCb420SP     0x2A
+#define  WIN_COLOR_DEPTH_YCbCr420SP     0x2B
+#define  WIN_COLOR_DEPTH_YCrCb422SP     0x2C
+#define  WIN_COLOR_DEPTH_YCbCr422SP     0x2D
+#define  WIN_COLOR_DEPTH_YUV444P        0x34
+#define  WIN_COLOR_DEPTH_YVU420SP       0x35
+#define  WIN_COLOR_DEPTH_YUV420SP       0x36
+#define  WIN_COLOR_DEPTH_YVU422SP       0x37
+#define  WIN_COLOR_DEPTH_YUV422SP       0x38
+#define  WIN_COLOR_DEPTH_YVU444SP       0x3B
+#define  WIN_COLOR_DEPTH_YUV444SP       0x3C
+
+#define DC_WIN_POSITION 0x704
+#define  H_POSITION(x) (((x) & 0xFFFF) <<  0) // Support negative.
+#define  V_POSITION(x) (((x) & 0xFFFF) << 16) // Support negative.
+
+#define DC_WIN_SIZE 0x705
+#define  H_SIZE(x) (((x) & 0x1FFF) <<  0)
+#define  V_SIZE(x) (((x) & 0x1FFF) << 16)
+
+#define DC_WIN_PRESCALED_SIZE 0x706
+#define  H_PRESCALED_SIZE(x) (((x) & 0x7FFF) <<  0)
+#define  V_PRESCALED_SIZE(x) (((x) & 0x1FFF) << 16)
+
+#define DC_WIN_H_INITIAL_DDA 0x707
+#define DC_WIN_V_INITIAL_DDA 0x708
+
+#define DC_WIN_DDA_INC 0x709
+#define  H_DDA_INC(x) (((x) & 0xFFFF) <<  0)
+#define  V_DDA_INC(x) (((x) & 0xFFFF) << 16)
+
+#define DC_WIN_LINE_STRIDE 0x70A
+#define  LINE_STRIDE(x)	   (x)
+#define  UV_LINE_STRIDE(x) (((x) & 0xFFFF) << 16)
+
+#define DC_WIN_DV_CONTROL 0x70E
+#define DV_CTRL_R(r) (((r) & 7) << 16)
+#define DV_CTRL_G(g) (((g) & 7) << 8)
+#define DV_CTRL_B(b) (((b) & 7) << 0)
+
+#define DC_WINBUF_BLEND_LAYER_CONTROL 0x716
+#define  WIN_BLEND_DEPTH(x) (((x) & 0xFF) << 0)
+#define  WIN_K1(x) (((x) & 0xFF) << 8)
+#define  WIN_K2(x) (((x) & 0xFF) << 16)
+#define  WIN_BLEND_ENABLE (0 << 24)
+#define  WIN_BLEND_BYPASS (1 << 24)
+
+#define DC_WINBUF_BLEND_MATCH_SELECT 0x717
+#define  WIN_BLEND_FACT_SRC_COLOR_MATCH_SEL_ZERO             (0 << 0)
+#define  WIN_BLEND_FACT_SRC_COLOR_MATCH_SEL_ONE              (1 << 0)
+#define  WIN_BLEND_FACT_SRC_COLOR_MATCH_SEL_K1               (2 << 0)
+#define  WIN_BLEND_FACT_SRC_COLOR_MATCH_SEL_K1_TIMES_DST     (3 << 0)
+#define  WIN_BLEND_FACT_SRC_COLOR_MATCH_SEL_NEG_K1_TIMES_DST (4 << 0)
+#define  WIN_BLEND_FACT_SRC_COLOR_MATCH_SEL_K1_TIMES_SRC     (5 << 0)
+
+#define  WIN_BLEND_FACT_DST_COLOR_MATCH_SEL_ZERO             (0 << 4)
+#define  WIN_BLEND_FACT_DST_COLOR_MATCH_SEL_ONE              (1 << 4)
+#define  WIN_BLEND_FACT_DST_COLOR_MATCH_SEL_K1               (2 << 4)
+#define  WIN_BLEND_FACT_DST_COLOR_MATCH_SEL_K2               (3 << 4)
+#define  WIN_BLEND_FACT_DST_COLOR_MATCH_SEL_K1_TIMES_DST     (4 << 4)
+#define  WIN_BLEND_FACT_DST_COLOR_MATCH_SEL_NEG_K1_TIMES_DST (5 << 4)
+#define  WIN_BLEND_FACT_DST_COLOR_MATCH_SEL_NEG_K1_TIMES_SRC (6 << 4)
+#define  WIN_BLEND_FACT_DST_COLOR_MATCH_SEL_NEG_K1           (7 << 4)
+
+#define  WIN_BLEND_FACT_SRC_ALPHA_MATCH_SEL_ZERO             (0 << 8)
+#define  WIN_BLEND_FACT_SRC_ALPHA_MATCH_SEL_K1               (1 << 8)
+#define  WIN_BLEND_FACT_SRC_ALPHA_MATCH_SEL_K2               (2 << 8)
+
+#define  WIN_BLEND_FACT_DST_ALPHA_MATCH_SEL_ZERO             (0 << 12)
+#define  WIN_BLEND_FACT_DST_ALPHA_MATCH_SEL_ONE              (1 << 12)
+#define  WIN_BLEND_FACT_DST_ALPHA_MATCH_SEL_NEG_K1_TIMES_SRC (2 << 12)
+#define  WIN_BLEND_FACT_DST_ALPHA_MATCH_SEL_K2               (3 << 12)
+
+#define DC_WINBUF_BLEND_ALPHA_1BIT 0x719
+#define  WIN_ALPHA_1BIT_WEIGHT0(x) (((x) & 0xFF) << 0)
+#define  WIN_ALPHA_1BIT_WEIGHT1(x) (((x) & 0xFF) << 8)
+
+/*! The following registers are A/B/C shadows of the 0xBC0/0xDC0/0xFC0 registers (see DISPLAY_WINDOW_HEADER). */
+#define DC_WINBUF_START_ADDR 0x800
+#define DC_WINBUF_ADDR_H_OFFSET 0x806
+#define DC_WINBUF_ADDR_V_OFFSET 0x808
+#define DC_WINBUF_SURFACE_KIND 0x80B
+#define  PITCH	(0 << 0)
+#define  TILED	(1 << 0)
+#define  BLOCK	(2 << 0)
+#define  BLOCK_HEIGHT(x) (((x) & 0x7) << 4)
+
+#define DC_WINBUF_MEMFETCH_CONTROL 0x82B
+
+/*! Display serial interface registers. */
+#define _DSIREG(reg) ((reg) * 4)
+
+#define DSI_INCR_SYNCPT_CNTRL 0x1
+#define  DSI_INCR_SYNCPT_SOFT_RESET BIT(0)
+#define  DSI_INCR_SYNCPT_NO_STALL   BIT(8)
+
+#define DSI_RD_DATA 0x9
+#define DSI_WR_DATA 0xA
+
+#define DSI_POWER_CONTROL 0xB
+#define  DSI_POWER_CONTROL_ENABLE 1
+
+#define DSI_INT_ENABLE 0xC
+#define DSI_INT_STATUS 0xD
+#define DSI_INT_MASK 0xE
+
+#define DSI_HOST_CONTROL 0xF
+#define  DSI_HOST_CONTROL_ECC          BIT(0)
+#define  DSI_HOST_CONTROL_CS           BIT(1)
+#define  DSI_HOST_CONTROL_PKT_BTA      BIT(2)
+#define  DSI_HOST_CONTROL_IMM_BTA      BIT(3)
+#define  DSI_HOST_CONTROL_FIFO_SEL     BIT(4)
+#define  DSI_HOST_CONTROL_HS           BIT(5)
+#define  DSI_HOST_CONTROL_RAW          BIT(6)
+#define  DSI_HOST_CONTROL_TX_TRIG_MASK (3 << 12)
+#define  DSI_HOST_CONTROL_TX_TRIG_SOL  (0 << 12)
+#define  DSI_HOST_CONTROL_TX_TRIG_FIFO (1 << 12)
+#define  DSI_HOST_CONTROL_TX_TRIG_HOST (2 << 12)
+#define  DSI_HOST_CONTROL_CRC_RESET    BIT(20)
+#define  DSI_HOST_CONTROL_FIFO_RESET   BIT(21)
+
+#define DSI_CONTROL 0x10
+#define  DSI_CONTROL_HOST_ENABLE  BIT(0)
+#define  DSI_CONTROL_VIDEO_ENABLE BIT(1)
+#define  DSI_CONTROL_SOURCE(s)    (((s) & 0x1) <<  2)
+#define  DSI_CONTROL_DCS_ENABLE   BIT(3)
+#define  DSI_CONTROL_LANES(n)     (((n) & 0x3) <<  4)
+#define  DSI_CONTROL_TX_TRIG(x)   (((x) & 0x3) <<  8)
+#define  DSI_CONTROL_FORMAT(f)    (((f) & 0x3) << 12)
+#define  DSI_CONTROL_CHANNEL(c)   (((c) & 0x3) << 16)
+#define  DSI_CONTROL_HS_CLK_CTRL  BIT(20)
+
+#define DSI_SOL_DELAY 0x11
+#define DSI_MAX_THRESHOLD 0x12
+
+#define DSI_TRIGGER 0x13
+#define  DSI_TRIGGER_VIDEO BIT(0)
+#define  DSI_TRIGGER_HOST  BIT(1)
+
+#define DSI_TX_CRC 0x14
+
+#define DSI_STATUS 0x15
+#define  DSI_STATUS_RX_FIFO_SIZE 0x1F
+
+#define DSI_INIT_SEQ_CONTROL 0x1A
+#define DSI_INIT_SEQ_DATA_0 0x1B
+#define DSI_INIT_SEQ_DATA_1 0x1C
+#define DSI_INIT_SEQ_DATA_2 0x1D
+#define DSI_INIT_SEQ_DATA_3 0x1E
+#define DSI_PKT_SEQ_0_LO 0x23
+#define DSI_PKT_SEQ_0_HI 0x24
+#define DSI_PKT_SEQ_1_LO 0x25
+#define DSI_PKT_SEQ_1_HI 0x26
+#define DSI_PKT_SEQ_2_LO 0x27
+#define DSI_PKT_SEQ_2_HI 0x28
+#define DSI_PKT_SEQ_3_LO 0x29
+#define DSI_PKT_SEQ_3_HI 0x2A
+#define DSI_PKT_SEQ_4_LO 0x2B
+#define DSI_PKT_SEQ_4_HI 0x2C
+#define DSI_PKT_SEQ_5_LO 0x2D
+#define DSI_PKT_SEQ_5_HI 0x2E
+#define DSI_DCS_CMDS 0x33
+
+#define DSI_PKT_LEN_0_1 0x34
+#define DSI_PKT_LEN_2_3 0x35
+#define DSI_PKT_LEN_4_5 0x36
+#define DSI_PKT_LEN_6_7 0x37
+#define  PKT0_LEN(x) (((x) & 0xFFFF) <<  0)
+#define  PKT1_LEN(x) (((x) & 0xFFFF) << 16)
+
+#define DSI_PHY_TIMING_0 0x3C
+#define DSI_PHY_TIMING_1 0x3D
+#define DSI_PHY_TIMING_2 0x3E
+#define DSI_BTA_TIMING 0x3F
+
+#define DSI_TIMEOUT_0 0x44
+#define  DSI_TIMEOUT_HTX(x) (((x) & 0xFFFF) <<  0)
+#define  DSI_TIMEOUT_LRX(x) (((x) & 0xFFFF) << 16)
+
+#define DSI_TIMEOUT_1 0x45
+#define  DSI_TIMEOUT_TA(x) (((x) & 0xFFFF) <<  0)
+#define  DSI_TIMEOUT_PR(x) (((x) & 0xFFFF) << 16)
+
+#define DSI_TO_TALLY 0x46
+
+#define DSI_PAD_CONTROL_0 0x4B
+#define  DSI_PAD_CONTROL_VS1_PDIO_CLK   BIT(8)
+#define  DSI_PAD_CONTROL_VS1_PDIO(x)    (((x) & 0xF) <<  0)
+#define  DSI_PAD_CONTROL_VS1_PULLDN_CLK BIT(24)
+#define  DSI_PAD_CONTROL_VS1_PULLDN(x)  (((x) & 0xF) << 16)
+
+#define DSI_PAD_CONTROL_CD 0x4C
+#define DSI_VIDEO_MODE_CONTROL 0x4E
+#define  DSI_CMD_PKT_VID_ENABLE 1
+#define  DSI_DSI_LINE_TYPE(x) ((x) << 1)
+
+#define DSI_PAD_CONTROL_1 0x4F
+#define DSI_PAD_CONTROL_2 0x50
+
+#define DSI_PAD_CONTROL_3 0x51
+#define  DSI_PAD_PREEMP_PU(x)     (((x) & 0x3) << 0)
+#define  DSI_PAD_PREEMP_PD(x)     (((x) & 0x3) << 4)
+#define  DSI_PAD_PREEMP_PU_CLK(x) (((x) & 0x3) << 8)
+#define  DSI_PAD_PREEMP_PD_CLK(x) (((x) & 0x3) << 12)
+
+#define DSI_PAD_CONTROL_4 0x52
+#define DSI_PAD_CONTROL_5_B01 0x53
+#define DSI_PAD_CONTROL_6_B01 0x54
+#define DSI_PAD_CONTROL_7_B01 0x55
+#define DSI_INIT_SEQ_DATA_15 0x5F
+#define DSI_INIT_SEQ_DATA_15_B01 0x62
+
+/*! DSI packet defines */
+#define DSI_ESCAPE_CMD	0x87
+#define DSI_ACK_NO_ERR	0x84
+
+#define ACK_ERROR_RES   0x02
+#define GEN_LONG_RD_RES 0x1A
+#define DCS_LONG_RD_RES 0x1C
+#define GEN_1_BYTE_SHORT_RD_RES 0x11
+#define DCS_1_BYTE_SHORT_RD_RES 0x21
+#define GEN_2_BYTE_SHORT_RD_RES 0x12
+#define DCS_2_BYTE_SHORT_RD_RES 0x22
+
+/*! MIPI registers. */
+#define MIPI_CAL_MIPI_CAL_CTRL          (0x00 / 0x4)
+#define MIPI_CAL_CIL_MIPI_CAL_STATUS    (0x08 / 0x4)
+#define MIPI_CAL_CILA_MIPI_CAL_CONFIG   (0x14 / 0x4)
+#define MIPI_CAL_CILB_MIPI_CAL_CONFIG   (0x18 / 0x4)
+#define MIPI_CAL_CILC_MIPI_CAL_CONFIG   (0x1C / 0x4)
+#define MIPI_CAL_CILD_MIPI_CAL_CONFIG   (0x20 / 0x4)
+#define MIPI_CAL_CILE_MIPI_CAL_CONFIG   (0x24 / 0x4)
+#define MIPI_CAL_CILF_MIPI_CAL_CONFIG   (0x28 / 0x4)
+#define MIPI_CAL_DSIA_MIPI_CAL_CONFIG   (0x38 / 0x4)
+#define MIPI_CAL_DSIB_MIPI_CAL_CONFIG   (0x3C / 0x4)
+#define MIPI_CAL_DSIC_MIPI_CAL_CONFIG   (0x40 / 0x4)
+#define MIPI_CAL_DSID_MIPI_CAL_CONFIG   (0x44 / 0x4)
+#define MIPI_CAL_MIPI_BIAS_PAD_CFG0     (0x58 / 0x4)
+#define MIPI_CAL_MIPI_BIAS_PAD_CFG1     (0x5C / 0x4)
+#define MIPI_CAL_MIPI_BIAS_PAD_CFG2     (0x60 / 0x4)
+#define MIPI_CAL_DSIA_MIPI_CAL_CONFIG_2 (0x64 / 0x4)
+#define MIPI_CAL_DSIB_MIPI_CAL_CONFIG_2 (0x68 / 0x4)
+#define MIPI_CAL_DSIC_MIPI_CAL_CONFIG_2 (0x70 / 0x4)
+#define MIPI_CAL_DSID_MIPI_CAL_CONFIG_2 (0x74 / 0x4)
+
+/*! MIPI CMDs. */
+#define MIPI_DSI_V_SYNC_START        0x01
+#define MIPI_DSI_COLOR_MODE_OFF      0x02
+#define MIPI_DSI_END_OF_TRANSMISSION 0x08
+#define MIPI_DSI_NULL_PACKET         0x09
+#define MIPI_DSI_V_SYNC_END          0x11
+#define MIPI_DSI_COLOR_MODE_ON       0x12
+#define MIPI_DSI_BLANKING_PACKET     0x19
+#define MIPI_DSI_H_SYNC_START        0x21
+#define MIPI_DSI_SHUTDOWN_PERIPHERAL 0x22
+#define MIPI_DSI_H_SYNC_END          0x31
+#define MIPI_DSI_TURN_ON_PERIPHERAL  0x32
+#define MIPI_DSI_SET_MAXIMUM_RETURN_PACKET_SIZE 0x37
+
+#define MIPI_DSI_DCS_SHORT_WRITE       0x05
+#define MIPI_DSI_DCS_READ              0x06
+#define MIPI_DSI_DCS_SHORT_WRITE_PARAM 0x15
+#define MIPI_DSI_DCS_LONG_WRITE        0x39
+
+#define MIPI_DSI_GENERIC_LONG_WRITE           0x29
+#define MIPI_DSI_GENERIC_SHORT_WRITE_0_PARAM  0x03
+#define MIPI_DSI_GENERIC_SHORT_WRITE_1_PARAM  0x13
+#define MIPI_DSI_GENERIC_SHORT_WRITE_2_PARAM  0x23
+#define MIPI_DSI_GENERIC_READ_REQUEST_0_PARAM 0x04
+#define MIPI_DSI_GENERIC_READ_REQUEST_1_PARAM 0x14
+#define MIPI_DSI_GENERIC_READ_REQUEST_2_PARAM 0x24
+
+/*! MIPI DCS CMDs. */
+#define MIPI_DCS_NOP                   0x00
+#define MIPI_DCS_SOFT_RESET            0x01
+#define MIPI_DCS_GET_COMPRESSION_MODE  0x03
+#define MIPI_DCS_GET_DISPLAY_ID        0x04
+#define MIPI_DCS_GET_DISPLAY_ID1       0xDA // GET_DISPLAY_ID Byte0, Module Manufacturer ID.
+#define MIPI_DCS_GET_DISPLAY_ID2       0xDB // GET_DISPLAY_ID Byte1, Module/Driver Version ID.
+#define MIPI_DCS_GET_DISPLAY_ID3       0xDC // GET_DISPLAY_ID Byte2, Module/Driver ID.
+#define MIPI_DCS_GET_NUM_ERRORS        0x05 // 1 byte.
+#define MIPI_DCS_GET_RED_CHANNEL       0x06
+#define MIPI_DCS_GET_GREEN_CHANNEL     0x07
+#define MIPI_DCS_GET_BLUE_CHANNEL      0x08
+#define MIPI_DCS_GET_DISPLAY_STATUS    0x09 // 4 bytes.
+#define MIPI_DCS_GET_POWER_MODE	       0x0A // 1 byte. 2: DISON, 3: NORON, 4: SLPOUT, 7: BSTON.
+#define MIPI_DCS_GET_ADDRESS_MODE      0x0B // Display Access Control. 1 byte. 0: GS, 1: SS, 3: BGR.
+#define MIPI_DCS_GET_PIXEL_FORMAT      0x0C // 1 byte. 4-6: DPI.
+#define MIPI_DCS_GET_DISPLAY_MODE      0x0D // 1 byte. 0-2: GCS, 3: ALLPOFF, 4: ALLPON, 5: INVON.
+#define MIPI_DCS_GET_SIGNAL_MODE       0x0E // 1 byte. 0: EODSI, 2: DEON, 3: PCLKON, 4: VSON, 5: HSON, 7: TEON.
+#define MIPI_DCS_GET_DIAGNOSTIC_RESULT 0x0F // 1 byte. 6: FUNDT, 7: REGLD.
+#define MIPI_DCS_ENTER_SLEEP_MODE      0x10
+#define MIPI_DCS_EXIT_SLEEP_MODE       0x11
+#define MIPI_DCS_ENTER_PARTIAL_MODE    0x12
+#define MIPI_DCS_ENTER_NORMAL_MODE     0x13
+#define MIPI_DCS_EXIT_INVERT_MODE      0x20
+#define MIPI_DCS_ENTER_INVERT_MODE     0x21
+#define MIPI_DCS_ALL_PIXELS_OFF        0x22
+#define MIPI_DCS_ALL_PIXELS_ON         0x23
+#define MIPI_DCS_SET_CONTRAST          0x25 // VCON in 40mV steps. 7-bit integer.
+#define MIPI_DCS_SET_GAMMA_CURVE       0x26 // 1 byte. 0-7: GC.
+#define MIPI_DCS_SET_DISPLAY_OFF       0x28
+#define MIPI_DCS_SET_DISPLAY_ON        0x29
+#define MIPI_DCS_SET_COLUMN_ADDRESS    0x2A
+#define MIPI_DCS_SET_PAGE_ADDRESS      0x2B
+#define MIPI_DCS_WRITE_MEMORY_START    0x2C
+#define MIPI_DCS_WRITE_LUT             0x2D // 24-bit: 192 bytes.
+#define MIPI_DCS_READ_MEMORY_START     0x2E
+#define MIPI_DCS_SET_PARTIAL_ROWS      0x30
+#define MIPI_DCS_SET_PARTIAL_COLUMNS   0x31
+#define MIPI_DCS_SET_SCROLL_AREA       0x33
+#define MIPI_DCS_SET_TEAR_OFF          0x34
+#define MIPI_DCS_SET_TEAR_ON           0x35
+#define MIPI_DCS_SET_ADDRESS_MODE      0x36 // Display Access Control. 1 byte. 0: GS, 1: SS, 3: BGR.
+#define MIPI_DCS_SET_SCROLL_START      0x37
+#define MIPI_DCS_EXIT_IDLE_MODE        0x38
+#define MIPI_DCS_ENTER_IDLE_MODE       0x39
+#define MIPI_DCS_SET_PIXEL_FORMAT      0x3A // 1 byte. 4-6: DPI.
+#define MIPI_DCS_WRITE_MEMORY_CONTINUE 0x3C
+#define MIPI_DCS_READ_MEMORY_CONTINUE  0x3E
+#define MIPI_DCS_GET_3D_CONTROL        0x3F
+#define MIPI_DCS_SET_VSYNC_TIMING      0x40
+#define MIPI_DCS_SET_TEAR_SCANLINE     0x44
+#define MIPI_DCS_GET_SCANLINE          0x45
+#define MIPI_DCS_SET_TEAR_SCANLINE_WIDTH 0x46
+#define MIPI_DCS_GET_SCANLINE_WIDTH    0x47
+#define MIPI_DSI_AREA_COLOR_MODE       0x4C
+#define MIPI_DCS_SET_BRIGHTNESS        0x51 // DCS_CONTROL_DISPLAY_BRIGHTNESS_CTRL. 1 byte. 0-7: DBV.
+#define MIPI_DCS_GET_BRIGHTNESS        0x52 // 1 byte. 0-7: DBV.
+#define MIPI_DCS_SET_CONTROL_DISPLAY   0x53 // 1 byte. 2: BL, 3: DD, 5: BCTRL.
+#define MIPI_DCS_GET_CONTROL_DISPLAY   0x54 // 1 byte. 2: BL, 3: DD, 5: BCTRL.
+#define MIPI_DCS_SET_CABC_VALUE        0x55 // 1 byte. 0-32: C, 4-7: C.
+#define MIPI_DCS_GET_CABC_VALUE        0x56 // 1 byte. 0-32: C, 4-7: C.
+#define MIPI_DCS_SET_CABC_MIN_BRI      0x5E // 1 byte. 0-7: CMB.
+#define MIPI_DCS_GET_CABC_MIN_BRI      0x5F // 1 byte. 0-7: CMB.
+#define MIPI_DCS_GET_AUTO_BRI_DIAG_RES 0x68 // 1 byte. 6-7: D.
+#define MIPI_DCS_READ_DDB_START        0xA1
+#define MIPI_DCS_READ_DDB_CONTINUE     0xA8 // 0x100 size.
+
+/*! MIPI DCS Panel Private CMDs. */
+#define MIPI_DCS_PRIV_SM_SET_COLOR_MODE 0xA0
+#define MIPI_DCS_PRIV_SM_SET_REG_OFFSET 0xB0
+#define MIPI_DCS_PRIV_SM_SET_ELVSS      0xB1 // OLED backlight tuning. Byte7: PWM transition time in frames.
+#define MIPI_DCS_PRIV_SET_POWER_CONTROL 0xB1
+#define MIPI_DCS_PRIV_SET_EXTC          0xB9 // Enable extended commands.
+#define MIPI_DCS_PRIV_UNK_BD            0xBD
+#define MIPI_DCS_PRIV_UNK_D5            0xD5
+#define MIPI_DCS_PRIV_UNK_D6            0xD6
+#define MIPI_DCS_PRIV_UNK_D8            0xD8
+#define MIPI_DCS_PRIV_UNK_D9            0xD9
+											 //                          LVL1 LVL2 LVL3 UNK0 UNK1
+#define MIPI_DCS_PRIV_SM_SET_REGS_LOCK  0xE2 // Samsung: Lock (default): 5A5A A5A5 A5A5 A500 A500. Unlock: A5A5 5A5A 5A5A UNK UNK.
+#define MIPI_DCS_PRIV_READ_EXTC_CMD_SPI 0xFE // Read EXTC Command In SPI. 1 byte. 0-6: EXT_SPI_CNT, 7:EXT_SP.
+#define MIPI_DCS_PRIV_SET_EXTC_CMD_REG  0xFF // EXTC Command Set enable register. 5 bytes. Pass: FF 98 06 04, PAGE.
+
+/*! MIPI DCS Panel Private CMDs PAGE 1. */
+#define MIPI_DCS_PRIV_GET_DISPLAY_ID4   0x00
+#define MIPI_DCS_PRIV_GET_DISPLAY_ID5   0x01
+#define MIPI_DCS_PRIV_GET_DISPLAY_ID6   0x02
+
+/*! MIPI DCS CMD Defines. */
+#define DCS_POWER_MODE_DISPLAY_ON           BIT(2)
+#define DCS_POWER_MODE_NORMAL_MODE          BIT(3)
+#define DCS_POWER_MODE_SLEEP_MODE           BIT(4)
+#define DCS_POWER_MODE_PARTIAL_MODE         BIT(5)
+#define DCS_POWER_MODE_IDLE_MODE            BIT(6)
+
+#define DCS_ADDRESS_MODE_V_FLIP             BIT(0)
+#define DCS_ADDRESS_MODE_H_FLIP             BIT(1)
+#define DCS_ADDRESS_MODE_LATCH_RL           BIT(2) // Latch Data Order.
+#define DCS_ADDRESS_MODE_BGR_COLOR          BIT(3)
+#define DCS_ADDRESS_MODE_LINE_ORDER         BIT(4) // Line Refresh Order.
+#define DCS_ADDRESS_MODE_SWAP_XY            BIT(5) // Page/Column Addressing Reverse Order.
+#define DCS_ADDRESS_MODE_MIRROR_X           BIT(6) // Column Address Order.
+#define DCS_ADDRESS_MODE_MIRROR_Y           BIT(7) // Page Address Order.
+#define DCS_ADDRESS_MODE_ROTATION_MASK      (0xF << 4)
+#define DCS_ADDRESS_MODE_ROTATION_90        (DCS_ADDRESS_MODE_SWAP_XY | DCS_ADDRESS_MODE_LINE_ORDER)
+#define DCS_ADDRESS_MODE_ROTATION_180       (DCS_ADDRESS_MODE_MIRROR_X | DCS_ADDRESS_MODE_LINE_ORDER)
+#define DCS_ADDRESS_MODE_ROTATION_270       (DCS_ADDRESS_MODE_SWAP_XY)
+
+#define DCS_GAMMA_CURVE_NONE                0
+#define DCS_GAMMA_CURVE_GC0_1_8             BIT(0)
+#define DCS_GAMMA_CURVE_GC1_2_5             BIT(1)
+#define DCS_GAMMA_CURVE_GC2_1_0             BIT(2)
+#define DCS_GAMMA_CURVE_GC3_1_0             BIT(3) // Are there more?
+
+#define DCS_CONTROL_DISPLAY_SM_FLASHLIGHT   BIT(2)
+#define DCS_CONTROL_DISPLAY_BACKLIGHT_CTRL  BIT(2)
+#define DCS_CONTROL_DISPLAY_DIMMING_CTRL    BIT(3)
+#define DCS_CONTROL_DISPLAY_BRIGHTNESS_CTRL BIT(5)
+
+#define DCS_SM_COLOR_MODE_SATURATED 0x00 // Disabled. Similar to vivid but over-saturated. Wide gamut?
+#define DCS_SM_COLOR_MODE_WASHED    0x45
+#define DCS_SM_COLOR_MODE_BASIC     0x03
+#define DCS_SM_COLOR_MODE_POR_RESET 0x20 // Reset value on power on.
+#define DCS_SM_COLOR_MODE_NATURAL   0x23 // Not actually natural..
+#define DCS_SM_COLOR_MODE_VIVID     0x65
+#define DCS_SM_COLOR_MODE_NIGHT0    0x43 // Based on washed out.
+#define DCS_SM_COLOR_MODE_NIGHT1    0x15 // Based on basic.
+#define DCS_SM_COLOR_MODE_NIGHT2    0x35 // Based on natural.
+#define DCS_SM_COLOR_MODE_NIGHT3    0x75 // Based on vivid.
+
+#define DCS_SM_COLOR_MODE_ENABLE    BIT(0)
+
+#define PANEL_SM_BL_CANDELA_MAX 2047
+
+/* Switch Panels:
+ *
+ * 6.2" panels for Icosa and Iowa SKUs:
+ * [10] 81 [26]: JDI LPM062M326A
+ * [10] 96 [09]: JDI LAM062M109A
+ * [20] 93 [0F]: InnoLux P062CCA-AZ1 (Rev A1)
+ * [20] 95 [0F]: InnoLux P062CCA-AZ2 (Rev B1)
+ * [20] 96 [0F]: InnoLux P062CCA-??? (Rev XX) [UNCONFIRMED MODEL+REV]
+ * [20] 97 [0F]: InnoLux P062CCA-??? (Rev XX) [UNCONFIRMED MODEL+REV]
+ * [20] 98 [0F]: InnoLux P062CCA-??? (Rev XX) [UNCONFIRMED MODEL+REV]
+ * [20] 99 [0F]: InnoLux P062CCA-??? (Rev XX) [UNCONFIRMED MODEL+REV]
+ * [30] 93 [0F]: AUO A062TAN00 (59.06A33.000)
+ * [30] 94 [0F]: AUO A062TAN01 (59.06A33.001)
+ * [30] 95 [0F]: AUO A062TAN02 (59.06A33.002)
+ * [30] 97 [0F]: AUO A062TAN02 (59.06A33.002) [From photo of assumed same panel]
+ * [30] 98 [0F]: AUO A062TAN0? [UNCONFIRMED MODEL]
+ * [30] XX [0F]: AUO A062TAN03 (59.06A33.003) [UNCONFIRMED ID]
+ *
+ *
+ * 5.5" panels for Hoag SKU:
+ * [20] 94 [10]: InnoLux 2J055IA-27A (Rev B1) (6203B001P4000)
+ * [20] 95 [10]: InnoLux 2J055IA-27A (Rev XX) [UNCONFIRMED MODEL+REV]
+ * [20] 96 [10]: InnoLux 2J055IA-27A (Rev XX) [UNCONFIRMED MODEL+REV]
+ * [30] 93 [10]: AUO A055TAN01 (59.05A30.001)
+ * [30] 94 [10]: AUO A055TAN02 (59.05A30.002)
+ * [30] 95 [10]: AUO A055TAN03 (59.05A30.003)
+ * [40] 94 [10]: Sharp LQ055T1SW10 (Rev P)
+ *
+ *
+ * 7.0" OLED panels for Aula SKU:
+ * [50] 9B [20]: Samsung AMS699VC01-0 (Rev 2.5)
+ */
+
+/* Display ID Decoding:
+ *
+ * byte0: Vendor
+ * byte1: Model
+ * byte2: Board
+ *
+ * Vendors:
+ * 10h: Japan Display Inc.
+ * 20h: InnoLux Corporation
+ * 30h: AU Optronics
+ * 40h: Sharp
+ * 50h: Samsung
+ *
+ * Boards, Panel Size:
+ * 0Fh: Icosa/Iowa, 6.2"
+ * 10h: Hoag,       5.5"
+ * 20h: Aula,       7.0"
+ */
+
+enum
+{
+	PANEL_JDI_XXX062M     = 0x10,
+	PANEL_JDI_LAM062M109A = 0x0910,
+	PANEL_JDI_LPM062M326A = 0x2610,
+	PANEL_INL_P062CCA_AZ1 = 0x0F20,
+	PANEL_AUO_A062TAN01   = 0x0F30,
+	PANEL_INL_2J055IA_27A = 0x1020,
+	PANEL_AUO_A055TAN01   = 0x1030,
+	PANEL_SHP_LQ055T1SW10 = 0x1040,
+	PANEL_SAM_AMS699VC01  = 0x2050,
+
+	// Found on 6/2" clones. Unknown markings. Quality seems JDI like. Has bad low backlight scaling. ID: [83] 94 [0F].
+	PANEL_OEM_CLONE_6_2   = 0x0F83,
+	// Found on 5.5" clones with AUO A055TAN02 (59.05A30.001) fake markings.
+	PANEL_OEM_CLONE_5_5   = 0x00B3,
+	// Found on 5.5" clones with AUO A055TAN02 (59.05A30.001) fake markings.
+	PANEL_OEM_CLONE       = 0x0000
+};
+
+void display_init();
+void display_backlight_pwm_init();
+void display_end();
+
+/*! Interrupt management. */
+void display_enable_interrupt(u32 intr);
+void display_disable_interrupt(u32 intr);
+void display_wait_interrupt(u32 intr);
+
+/*! Get/Set Display panel ID. */
+u16  display_get_decoded_panel_id();
+void display_set_decoded_panel_id(u32 id);
+
+/*! MIPI DCS register management */
+int  display_dsi_read(u8 cmd, u32 len, void *data);
+int  display_dsi_vblank_read(u8 cmd, u32 len, void *data);
+void display_dsi_write(u8 cmd, u32 len, void *data);
+void display_dsi_vblank_write(u8 cmd, u32 len, void *data);
+
+/*! Show one single color on the display. */
+void display_color_screen(u32 color);
+
+/*! Switches screen backlight ON/OFF. */
+void display_backlight(bool enable);
+void display_backlight_brightness(u32 brightness, u32 step_delay);
+u32  display_get_backlight_brightness();
+
+u32 *display_init_window_a_pitch();
+u32 *display_init_window_a_pitch_vic();
+u32 *display_init_window_a_pitch_inv();
+u32 *display_init_window_a_block();
+u32 *display_init_window_d_console();
+
+void display_window_disable(u32 window);
+
+void display_set_framebuffer(u32 window,  void *fb);
+void display_move_framebuffer(u32 window, void *fb);
+
+void display_window_d_console_enable();
+void display_window_d_console_disable();
+
+void display_cursor_init(void *crs_fb, u32 size);
+void display_cursor_set_pos(u32 x, u32 y);
+void display_cursor_deinit();
+
+#endif

bdk/display/di.inl

@@ -0,0 +1,573 @@
+/*
+* Copyright (c) 2018 naehrwert
+* Copyright (c) 2018-2024 CTCaer
+*
+* This program is free software; you can redistribute it and/or modify it
+* under the terms and conditions of the GNU General Public License,
+* version 2, as published by the Free Software Foundation.
+*
+* This program is distributed in the hope it will be useful, but WITHOUT
+* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+* FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+* more details.
+*
+* You should have received a copy of the GNU General Public License
+* along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+// Display A config.
+static const reg_cfg_t _di_dc_setup_win_config[] = {
+	{DC_CMD_STATE_ACCESS, READ_MUX_ASSEMBLY | WRITE_MUX_ASSEMBLY},
+	{DC_CMD_STATE_CONTROL, GENERAL_UPDATE},
+	{DC_CMD_STATE_CONTROL, GENERAL_ACT_REQ},
+	{DC_CMD_REG_ACT_CONTROL, WIN_A_ACT_HCNTR_SEL | WIN_B_ACT_HCNTR_SEL | WIN_C_ACT_HCNTR_SEL},
+	{DC_CMD_STATE_CONTROL, GENERAL_UPDATE},
+	{DC_CMD_STATE_CONTROL, GENERAL_ACT_REQ},
+	{DC_DISP_DC_MCCIF_FIFOCTRL, 0},
+	{DC_DISP_DISP_MEM_HIGH_PRIORITY, 0},
+	{DC_DISP_DISP_MEM_HIGH_PRIORITY_TIMER, 0},
+	{DC_CMD_DISPLAY_POWER_CONTROL, PW0_ENABLE | PW1_ENABLE | PW2_ENABLE | PW3_ENABLE | PW4_ENABLE | PM0_ENABLE | PM1_ENABLE},
+	{DC_CMD_GENERAL_INCR_SYNCPT_CNTRL, SYNCPT_CNTRL_NO_STALL},
+	{DC_CMD_CONT_SYNCPT_VSYNC, SYNCPT_VSYNC_ENABLE | SYNCPT_VSYNC_INDX(9)},
+	{DC_CMD_STATE_CONTROL, GENERAL_UPDATE  | WIN_A_UPDATE  | WIN_B_UPDATE  | WIN_C_UPDATE  | WIN_D_UPDATE},
+	{DC_CMD_STATE_CONTROL, GENERAL_ACT_REQ | WIN_A_ACT_REQ | WIN_B_ACT_REQ | WIN_C_ACT_REQ | WIN_D_ACT_REQ},
+
+	/* Setup Windows A/B/C */
+	{DC_CMD_DISPLAY_WINDOW_HEADER, WINDOW_A_SELECT | WINDOW_B_SELECT | WINDOW_C_SELECT | WINDOW_D_SELECT},
+	{DC_WIN_WIN_OPTIONS, 0},
+	{DC_WIN_DV_CONTROL,  0},
+	/* Setup default YUV colorspace conversion coefficients */
+	{DC_WINC_CSC_YOF,   0xF0},
+	{DC_WINC_CSC_KYRGB, 0x12A},
+	{DC_WINC_CSC_KUR,   0},
+	{DC_WINC_CSC_KVR,   0x198},
+	{DC_WINC_CSC_KUG,   0x39B},
+	{DC_WINC_CSC_KVG,   0x32F},
+	{DC_WINC_CSC_KUB,   0x204},
+	{DC_WINC_CSC_KVB,   0},
+	/* End of color coefficients */
+
+	{DC_DISP_DISP_COLOR_CONTROL, BASE_COLOR_SIZE_888},
+	{DC_DISP_DISP_INTERFACE_CONTROL, DISP_DATA_FORMAT_DF1P1C},
+	{DC_COM_PIN_OUTPUT_POLARITY(1), LSC0_OUTPUT_POLARITY_LOW},
+	{DC_COM_PIN_OUTPUT_POLARITY(3), 0},
+	{DC_DISP_BLEND_BACKGROUND_COLOR, 0},
+	{DC_COM_CRC_CONTROL, 0},
+	{DC_CMD_STATE_CONTROL, GENERAL_UPDATE  | WIN_A_UPDATE  | WIN_B_UPDATE  | WIN_C_UPDATE  | WIN_D_UPDATE},
+	{DC_CMD_STATE_CONTROL, GENERAL_ACT_REQ | WIN_A_ACT_REQ | WIN_B_ACT_REQ | WIN_C_ACT_REQ | WIN_D_ACT_REQ},
+	{DC_WINBUF_BLEND_LAYER_CONTROL, WIN_BLEND_BYPASS | WIN_BLEND_DEPTH(255)},
+	{DC_CMD_DISPLAY_COMMAND_OPTION0, 0},
+	{DC_DISP_DISP_WIN_OPTIONS, 0},
+	{DC_CMD_DISPLAY_COMMAND, DISP_CTRL_MODE_STOP},
+	{DC_CMD_STATE_CONTROL, GENERAL_UPDATE  | WIN_A_UPDATE  | WIN_B_UPDATE  | WIN_C_UPDATE  | WIN_D_UPDATE},
+	{DC_CMD_STATE_CONTROL, GENERAL_ACT_REQ | WIN_A_ACT_REQ | WIN_B_ACT_REQ | WIN_C_ACT_REQ | WIN_D_ACT_REQ}
+};
+
+// DSI Init config.
+static const reg_cfg_t _di_dsi_seq_pkt_reset_config0[] = {
+	{DSI_WR_DATA, 0},
+	{DSI_INT_ENABLE, 0},
+	{DSI_INT_STATUS, 0},
+	{DSI_INT_MASK,   0},
+	{DSI_INIT_SEQ_DATA_0, 0},
+	{DSI_INIT_SEQ_DATA_1, 0},
+	{DSI_INIT_SEQ_DATA_2, 0},
+	{DSI_INIT_SEQ_DATA_3, 0}
+};
+static const reg_cfg_t _di_dsi_seq_pkt_reset_config1[] = {
+	{DSI_DCS_CMDS, 0},
+	{DSI_PKT_SEQ_0_LO, 0},
+	{DSI_PKT_SEQ_1_LO, 0},
+	{DSI_PKT_SEQ_2_LO, 0},
+	{DSI_PKT_SEQ_3_LO, 0},
+	{DSI_PKT_SEQ_4_LO, 0},
+	{DSI_PKT_SEQ_5_LO, 0},
+	{DSI_PKT_SEQ_0_HI, 0},
+	{DSI_PKT_SEQ_1_HI, 0},
+	{DSI_PKT_SEQ_2_HI, 0},
+	{DSI_PKT_SEQ_3_HI, 0},
+	{DSI_PKT_SEQ_4_HI, 0},
+	{DSI_PKT_SEQ_5_HI, 0},
+	{DSI_CONTROL, 0}
+};
+static const reg_cfg_t _di_dsi_init_pads_t210b01[] = {
+	{DSI_PAD_CONTROL_1, 0},
+	{DSI_PAD_CONTROL_2, 0},
+	{DSI_PAD_CONTROL_3, 0},
+	{DSI_PAD_CONTROL_4, 0},
+	{DSI_PAD_CONTROL_5_B01, 0},
+	{DSI_PAD_CONTROL_6_B01, 0},
+	{DSI_PAD_CONTROL_7_B01, 0}
+};
+static const reg_cfg_t _di_dsi_init_config[] = {
+	{DSI_PAD_CONTROL_CD, 0},
+	{DSI_SOL_DELAY,     24},
+	{DSI_MAX_THRESHOLD, 480},
+	{DSI_TRIGGER, 0},
+	{DSI_INIT_SEQ_CONTROL, 0},
+
+	{DSI_PKT_LEN_0_1, 0},
+	{DSI_PKT_LEN_2_3, 0},
+	{DSI_PKT_LEN_4_5, 0},
+	{DSI_PKT_LEN_6_7, 0},
+
+	{DSI_PAD_CONTROL_1, 0},
+
+	/* DSI PHY timings */
+	{DSI_PHY_TIMING_0, 0x6070603},
+	{DSI_PHY_TIMING_1, 0x40A0E05},
+	{DSI_PHY_TIMING_2, 0x30109},
+	{DSI_BTA_TIMING,   0x190A14},
+	/* DSI timeout */
+	{DSI_TIMEOUT_0, DSI_TIMEOUT_LRX(0x2000) | DSI_TIMEOUT_HTX(0xFFFF)},
+	{DSI_TIMEOUT_1, DSI_TIMEOUT_PR(0x765)   | DSI_TIMEOUT_TA(0x2000)},
+	{DSI_TO_TALLY, 0},
+
+	{DSI_PAD_CONTROL_0, DSI_PAD_CONTROL_VS1_PULLDN(0) | DSI_PAD_CONTROL_VS1_PDIO(0)}, // Power up.
+	{DSI_POWER_CONTROL, DSI_POWER_CONTROL_ENABLE},
+	{DSI_POWER_CONTROL, DSI_POWER_CONTROL_ENABLE},
+	{DSI_POWER_CONTROL, 0},
+	{DSI_POWER_CONTROL, 0},
+	{DSI_PAD_CONTROL_1, 0},
+
+	/* DSI PHY timings */
+	{DSI_PHY_TIMING_0, 0x6070603},
+	{DSI_PHY_TIMING_1, 0x40A0E05},
+	{DSI_PHY_TIMING_2, 0x30118},
+	{DSI_BTA_TIMING,   0x190A14},
+	/* DSI timeout */
+	{DSI_TIMEOUT_0, DSI_TIMEOUT_LRX(0x2000) | DSI_TIMEOUT_HTX(0xFFFF)},
+	{DSI_TIMEOUT_1, DSI_TIMEOUT_PR(0x1343)  | DSI_TIMEOUT_TA(0x2000)},
+	{DSI_TO_TALLY, 0},
+
+	{DSI_HOST_CONTROL, DSI_HOST_CONTROL_CRC_RESET | DSI_HOST_CONTROL_TX_TRIG_HOST | DSI_HOST_CONTROL_CS | DSI_HOST_CONTROL_ECC},
+	{DSI_CONTROL, DSI_CONTROL_LANES(3) | DSI_CONTROL_HOST_ENABLE},
+	{DSI_POWER_CONTROL, DSI_POWER_CONTROL_ENABLE},
+	{DSI_POWER_CONTROL, DSI_POWER_CONTROL_ENABLE},
+	{DSI_MAX_THRESHOLD, 64},
+	{DSI_TRIGGER, 0},
+	{DSI_TX_CRC, 0},
+	{DSI_INIT_SEQ_CONTROL, 0}
+};
+
+// DSI panel JDI config.
+static const reg_cfg_t _di_dsi_panel_init_config_jdi[] = {
+	{DSI_WR_DATA, 0x0439},     // MIPI_DSI_DCS_LONG_WRITE: 4 bytes.
+	{DSI_WR_DATA, 0x9483FFB9}, // MIPI_DCS_PRIV_SET_EXTC. (Pass: FF 83 94).
+	{DSI_TRIGGER, DSI_TRIGGER_HOST},
+	{DSI_WR_DATA, 0xBD15},     // MIPI_DSI_DCS_SHORT_WRITE_PARAM: 0 to 0xBD.
+	{DSI_TRIGGER, DSI_TRIGGER_HOST},
+	{DSI_WR_DATA, 0x1939},     // MIPI_DSI_DCS_LONG_WRITE: 25 bytes.
+	{DSI_WR_DATA, 0xAAAAAAD8}, // Register: 0xD8.
+	{DSI_WR_DATA, 0xAAAAAAEB},
+	{DSI_WR_DATA, 0xAAEBAAAA},
+	{DSI_WR_DATA, 0xAAAAAAAA},
+	{DSI_WR_DATA, 0xAAAAAAEB},
+	{DSI_WR_DATA, 0xAAEBAAAA},
+	{DSI_WR_DATA, 0xAA},
+	{DSI_TRIGGER, DSI_TRIGGER_HOST},
+	{DSI_WR_DATA, 0x01BD15},   // MIPI_DSI_DCS_SHORT_WRITE_PARAM: 1 to 0xBD.
+	{DSI_TRIGGER, DSI_TRIGGER_HOST},
+	{DSI_WR_DATA, 0x2739},     // MIPI_DSI_DCS_LONG_WRITE: 39 bytes.
+	{DSI_WR_DATA, 0xFFFFFFD8}, // Register: 0xD8.
+	{DSI_WR_DATA, 0xFFFFFFFF},
+	{DSI_WR_DATA, 0xFFFFFFFF},
+	{DSI_WR_DATA, 0xFFFFFFFF},
+	{DSI_WR_DATA, 0xFFFFFFFF},
+	{DSI_WR_DATA, 0xFFFFFFFF},
+	{DSI_WR_DATA, 0xFFFFFFFF},
+	{DSI_WR_DATA, 0xFFFFFFFF},
+	{DSI_WR_DATA, 0xFFFFFFFF},
+	{DSI_WR_DATA, 0xFFFFFF},
+	{DSI_TRIGGER, DSI_TRIGGER_HOST},
+	{DSI_WR_DATA, 0x02BD15},   // MIPI_DSI_DCS_SHORT_WRITE_PARAM: 2 to 0xBD.
+	{DSI_TRIGGER, DSI_TRIGGER_HOST},
+	{DSI_WR_DATA, 0xF39},      // MIPI_DSI_DCS_LONG_WRITE: 15 bytes.
+	{DSI_WR_DATA, 0xFFFFFFD8}, // Register: 0xD8.
+	{DSI_WR_DATA, 0xFFFFFFFF},
+	{DSI_WR_DATA, 0xFFFFFFFF},
+	{DSI_WR_DATA, 0xFFFFFF},
+	{DSI_TRIGGER, DSI_TRIGGER_HOST},
+	{DSI_WR_DATA, 0x00BD15},   // MIPI_DSI_DCS_SHORT_WRITE_PARAM: 0 to 0xBD.
+	{DSI_TRIGGER, DSI_TRIGGER_HOST},
+	{DSI_WR_DATA, 0x06D915},   // MIPI_DSI_DCS_SHORT_WRITE_PARAM: 6 to 0xD9.
+	{DSI_TRIGGER, DSI_TRIGGER_HOST},
+	{DSI_WR_DATA, 0x439},      // MIPI_DSI_DCS_LONG_WRITE: 4 bytes.
+	{DSI_WR_DATA, 0x000000B9}, // MIPI_DCS_PRIV_SET_EXTC. Disable.
+	{DSI_TRIGGER, DSI_TRIGGER_HOST}
+};
+
+// DSI packet config.
+static const reg_cfg_t _di_dsi_seq_pkt_video_non_burst_no_eot_config[] = {
+	{DSI_PAD_CONTROL_1, 0},
+
+	/* DSI PHY timings */
+	{DSI_PHY_TIMING_0, 0x6070603},
+	{DSI_PHY_TIMING_1, 0x40A0E05},
+	{DSI_PHY_TIMING_2, 0x30172},
+	{DSI_BTA_TIMING,   0x190A14},
+	/* DSI timeout */
+	{DSI_TIMEOUT_0, DSI_TIMEOUT_LRX(0x2000) | DSI_TIMEOUT_HTX(0xA40)},
+	{DSI_TIMEOUT_1, DSI_TIMEOUT_PR(0x5A2F)  | DSI_TIMEOUT_TA(0x2000)},
+	{DSI_TO_TALLY, 0},
+
+	{DSI_PKT_SEQ_0_LO, 0x40000208},
+	{DSI_PKT_SEQ_2_LO, 0x40000308},
+	{DSI_PKT_SEQ_4_LO, 0x40000308},
+	{DSI_PKT_SEQ_1_LO, 0x40000308},
+	{DSI_PKT_SEQ_3_LO, 0x3F3B2B08},
+	{DSI_PKT_SEQ_3_HI, 0x2CC},
+	{DSI_PKT_SEQ_5_LO, 0x3F3B2B08},
+	{DSI_PKT_SEQ_5_HI, 0x2CC},
+	{DSI_PKT_LEN_0_1, PKT1_LEN(206)  | PKT0_LEN(0)},
+	{DSI_PKT_LEN_2_3, PKT1_LEN(2160) | PKT0_LEN(418)},
+	{DSI_PKT_LEN_4_5, PKT1_LEN(0)    | PKT0_LEN(400)},
+	{DSI_PKT_LEN_6_7, PKT1_LEN(0)    | PKT0_LEN(400)},
+	{DSI_HOST_CONTROL, 0}
+};
+
+// DSI mode config.
+static const reg_cfg_t _di_dsi_host_mode_config[] = {
+	{DSI_TRIGGER, 0},
+	{DSI_CONTROL, 0},
+	{DSI_SOL_DELAY, 6},
+	{DSI_MAX_THRESHOLD, 480},
+	{DSI_POWER_CONTROL, DSI_POWER_CONTROL_ENABLE},
+	{DSI_CONTROL, DSI_CONTROL_HS_CLK_CTRL | DSI_CONTROL_FORMAT(3) | DSI_CONTROL_LANES(3) | DSI_CONTROL_VIDEO_ENABLE},
+	{DSI_HOST_CONTROL, DSI_HOST_CONTROL_HS | DSI_HOST_CONTROL_FIFO_SEL | DSI_HOST_CONTROL_CS | DSI_HOST_CONTROL_ECC},
+	{DSI_CONTROL, DSI_CONTROL_HS_CLK_CTRL | DSI_CONTROL_FORMAT(3) | DSI_CONTROL_LANES(3) | DSI_CONTROL_VIDEO_ENABLE},
+	{DSI_HOST_CONTROL, DSI_HOST_CONTROL_TX_TRIG_SOL | DSI_HOST_CONTROL_CS | DSI_HOST_CONTROL_ECC},
+	{DSI_HOST_CONTROL, DSI_HOST_CONTROL_HS | DSI_HOST_CONTROL_TX_TRIG_SOL | DSI_HOST_CONTROL_CS | DSI_HOST_CONTROL_ECC}
+};
+
+// MIPI CAL config.
+static const reg_cfg_t _di_mipi_pad_cal_config[] = {
+	{MIPI_CAL_MIPI_BIAS_PAD_CFG2,  0},
+	{MIPI_CAL_CIL_MIPI_CAL_STATUS, 0xF3F10000},
+	{MIPI_CAL_MIPI_BIAS_PAD_CFG0,  0},
+	{MIPI_CAL_MIPI_BIAS_PAD_CFG2,  0}
+};
+
+// DSI pad config.
+static const reg_cfg_t _di_dsi_pad_cal_config_t210[] = {
+	{DSI_PAD_CONTROL_1, 0},
+	{DSI_PAD_CONTROL_2, 0},
+	{DSI_PAD_CONTROL_3, DSI_PAD_PREEMP_PD_CLK(0x3) | DSI_PAD_PREEMP_PU_CLK(0x3) | DSI_PAD_PREEMP_PD(0x03) | DSI_PAD_PREEMP_PU(0x3)},
+	{DSI_PAD_CONTROL_4, 0}
+};
+static const reg_cfg_t _di_dsi_pad_cal_config_t210b01[] = {
+	{DSI_PAD_CONTROL_1,     0},
+	{DSI_PAD_CONTROL_2,     0},
+	{DSI_PAD_CONTROL_3,     0},
+	{DSI_PAD_CONTROL_4,     0x77777},
+	{DSI_PAD_CONTROL_5_B01, 0x77777},
+	{DSI_PAD_CONTROL_6_B01, DSI_PAD_PREEMP_PD_CLK(0x1) | DSI_PAD_PREEMP_PU_CLK(0x1) | DSI_PAD_PREEMP_PD(0x01) | DSI_PAD_PREEMP_PU(0x1)},
+	{DSI_PAD_CONTROL_7_B01, 0}
+};
+
+// MIPI CAL config.
+static const reg_cfg_t _di_mipi_dsi_cal_prod_config_t210[] = {
+	{MIPI_CAL_DSIA_MIPI_CAL_CONFIG,   0x200200},
+	{MIPI_CAL_DSIB_MIPI_CAL_CONFIG,   0x200200},
+	{MIPI_CAL_DSIA_MIPI_CAL_CONFIG_2, 0x200002},
+	{MIPI_CAL_DSIB_MIPI_CAL_CONFIG_2, 0x200002}
+};
+static const reg_cfg_t _di_mipi_dsi_cal_prod_config_t210b01[] = {
+	{MIPI_CAL_DSIA_MIPI_CAL_CONFIG,   0x200006},
+	{MIPI_CAL_DSIB_MIPI_CAL_CONFIG,   0x200006},
+	{MIPI_CAL_DSIA_MIPI_CAL_CONFIG_2, 0x260000},
+	{MIPI_CAL_DSIB_MIPI_CAL_CONFIG_2, 0x260000}
+};
+static const reg_cfg_t _di_mipi_dsi_cal_unused_config[] = {
+	{MIPI_CAL_CILA_MIPI_CAL_CONFIG,   0},
+	{MIPI_CAL_CILB_MIPI_CAL_CONFIG,   0},
+	{MIPI_CAL_CILC_MIPI_CAL_CONFIG,   0},
+	{MIPI_CAL_CILD_MIPI_CAL_CONFIG,   0},
+	{MIPI_CAL_CILE_MIPI_CAL_CONFIG,   0},
+	{MIPI_CAL_CILF_MIPI_CAL_CONFIG,   0},
+	{MIPI_CAL_DSIC_MIPI_CAL_CONFIG,   0},
+	{MIPI_CAL_DSID_MIPI_CAL_CONFIG,   0},
+	{MIPI_CAL_DSIB_MIPI_CAL_CONFIG_2, 0},
+	{MIPI_CAL_DSIC_MIPI_CAL_CONFIG_2, 0},
+	{MIPI_CAL_DSID_MIPI_CAL_CONFIG_2, 0}
+};
+
+// Display A enable config.
+static const reg_cfg_t _di_dc_video_enable_config[] = {
+	/* Set panel timings */
+	{DC_DISP_DISP_TIMING_OPTIONS, VSYNC_H_POSITION(0)},
+	{DC_DISP_REF_TO_SYNC, V_REF_TO_SYNC(1)    | H_REF_TO_SYNC(0)},
+	{DC_DISP_SYNC_WIDTH,  V_SYNC_WIDTH(1)     | H_SYNC_WIDTH(72)},
+	{DC_DISP_BACK_PORCH,  V_BACK_PORCH(9)     | H_BACK_PORCH(72)},
+	{DC_DISP_FRONT_PORCH, V_FRONT_PORCH(10)   | H_FRONT_PORCH(136)},
+	{DC_DISP_ACTIVE,      V_DISP_ACTIVE(1280) | H_DISP_ACTIVE(720)},
+	/* End of Display timings */
+
+	{DC_DISP_SHIFT_CLOCK_OPTIONS, SC1_H_QUALIFIER_NONE | SC0_H_QUALIFIER_NONE},
+	{DC_COM_PIN_OUTPUT_ENABLE(1), 0},
+	{DC_DISP_DATA_ENABLE_OPTIONS, DE_SELECT_ACTIVE | DE_CONTROL_NORMAL},
+	{DC_DISP_DISP_CLOCK_CONTROL, 0},
+
+	/* Start continuous display. */
+	{DC_CMD_DISPLAY_COMMAND, DISP_CTRL_MODE_C_DISPLAY},
+	{DC_CMD_STATE_CONTROL, GENERAL_UPDATE},
+	{DC_CMD_STATE_CONTROL, GENERAL_ACT_REQ},
+	{DC_CMD_STATE_CONTROL, GENERAL_UPDATE},
+	{DC_CMD_STATE_CONTROL, GENERAL_ACT_REQ},
+	{DC_CMD_GENERAL_INCR_SYNCPT, SYNCPT_GENERAL_COND(COND_REG_WR_SAFE) | SYNCPT_GENERAL_INDX(1)},
+	{DC_CMD_GENERAL_INCR_SYNCPT, SYNCPT_GENERAL_COND(COND_REG_WR_SAFE) | SYNCPT_GENERAL_INDX(1)},
+	{DC_CMD_STATE_CONTROL, GENERAL_UPDATE},
+	{DC_CMD_STATE_CONTROL, GENERAL_ACT_REQ},
+
+	{DC_DISP_DISP_CLOCK_CONTROL, PIXEL_CLK_DIVIDER_PCD1 | SHIFT_CLK_DIVIDER(4)}, // 4: div3.
+};
+
+// Display A disable config.
+static const reg_cfg_t _di_dc_video_disable_config[] = {
+	{DC_CMD_INT_MASK, 0},
+	{DC_CMD_STATE_ACCESS, READ_MUX_ASSEMBLY | WRITE_MUX_ASSEMBLY},
+	{DC_CMD_INT_ENABLE, 0},
+	{DC_CMD_CONT_SYNCPT_VSYNC, 0},
+
+	/* Stop display. */
+	{DC_CMD_DISPLAY_COMMAND, DISP_CTRL_MODE_STOP},
+	{DC_CMD_STATE_CONTROL, GENERAL_UPDATE},
+	{DC_CMD_STATE_CONTROL, GENERAL_ACT_REQ},
+	{DC_CMD_STATE_CONTROL, GENERAL_UPDATE},
+	{DC_CMD_STATE_CONTROL, GENERAL_ACT_REQ},
+	{DC_CMD_GENERAL_INCR_SYNCPT, SYNCPT_GENERAL_COND(COND_REG_WR_SAFE) | SYNCPT_GENERAL_INDX(1)},
+	{DC_CMD_GENERAL_INCR_SYNCPT, SYNCPT_GENERAL_COND(COND_REG_WR_SAFE) | SYNCPT_GENERAL_INDX(1)},
+	{DC_CMD_STATE_CONTROL, GENERAL_UPDATE},
+	{DC_CMD_STATE_CONTROL, GENERAL_ACT_REQ},
+	// TODO: LCD panels should sleep for 40ms here.
+	{DC_CMD_DISPLAY_POWER_CONTROL, 0},
+	{DC_CMD_STATE_CONTROL, GENERAL_UPDATE},
+	{DC_CMD_STATE_CONTROL, GENERAL_ACT_REQ},
+};
+
+// DSI deinit config.
+static const reg_cfg_t _di_dsi_timing_deinit_config[] = {
+	{DSI_POWER_CONTROL, 0},
+	{DSI_PAD_CONTROL_1, 0},
+
+	/* DSI PHY timings */
+	{DSI_PHY_TIMING_0, 0x6070603},
+	{DSI_PHY_TIMING_1, 0x40A0E05},
+	{DSI_PHY_TIMING_2, 0x30118},
+	{DSI_BTA_TIMING,   0x190A14},
+	/* DSI timeout */
+	{DSI_TIMEOUT_0, DSI_TIMEOUT_LRX(0x2000) | DSI_TIMEOUT_HTX(0xFFFF)},
+	{DSI_TIMEOUT_1, DSI_TIMEOUT_PR(0x1343)  | DSI_TIMEOUT_TA(0x2000)},
+	{DSI_TO_TALLY, 0},
+
+	{DSI_HOST_CONTROL, DSI_HOST_CONTROL_CRC_RESET | DSI_HOST_CONTROL_TX_TRIG_HOST | DSI_HOST_CONTROL_CS | DSI_HOST_CONTROL_ECC},
+	{DSI_CONTROL, DSI_CONTROL_LANES(3) | DSI_CONTROL_HOST_ENABLE},
+	{DSI_POWER_CONTROL, DSI_POWER_CONTROL_ENABLE},
+	{DSI_MAX_THRESHOLD, 64},
+	{DSI_TRIGGER, 0},
+	{DSI_TX_CRC, 0},
+	{DSI_INIT_SEQ_CONTROL, 0}
+};
+
+// DSI panel JDI deinit config.
+static const reg_cfg_t _di_dsi_panel_deinit_config_jdi[] = {
+	{DSI_WR_DATA, 0x439},      // MIPI_DSI_DCS_LONG_WRITE: 4 bytes.
+	{DSI_WR_DATA, 0x9483FFB9}, // MIPI_DCS_PRIV_SET_EXTC. (Pass: FF 83 94).
+	{DSI_TRIGGER, DSI_TRIGGER_HOST},
+	{DSI_WR_DATA, 0x2139},     // MIPI_DSI_DCS_LONG_WRITE: 33 bytes.
+	{DSI_WR_DATA, 0x191919D5}, // Register: 0xD5.
+	{DSI_WR_DATA, 0x19191919},
+	{DSI_WR_DATA, 0x19191919},
+	{DSI_WR_DATA, 0x19191919},
+	{DSI_WR_DATA, 0x19191919},
+	{DSI_WR_DATA, 0x19191919},
+	{DSI_WR_DATA, 0x19191919},
+	{DSI_WR_DATA, 0x19191919},
+	{DSI_WR_DATA, 0x19},
+	{DSI_TRIGGER, DSI_TRIGGER_HOST},
+	{DSI_WR_DATA, 0xB39},      // MIPI_DSI_DCS_LONG_WRITE: 11 bytes.
+	{DSI_WR_DATA, 0x4F0F41B1}, // MIPI_DCS_PRIV_SET_POWER_CONTROL.
+	{DSI_WR_DATA, 0xF179A433},
+	{DSI_WR_DATA, 0x002D81},
+	{DSI_TRIGGER, DSI_TRIGGER_HOST},
+	{DSI_WR_DATA, 0x439},      // MIPI_DSI_DCS_LONG_WRITE: 4 bytes.
+	{DSI_WR_DATA, 0x000000B9}, // MIPI_DCS_PRIV_SET_EXTC. Disable.
+	{DSI_TRIGGER, DSI_TRIGGER_HOST}
+};
+
+// DSI panel AUO deinit config.
+static const reg_cfg_t _di_dsi_panel_deinit_config_auo[] = {
+	{DSI_WR_DATA, 0x439},      // MIPI_DSI_DCS_LONG_WRITE: 4 bytes.
+	{DSI_WR_DATA, 0x9483FFB9}, // MIPI_DCS_PRIV_SET_EXTC. (Pass: FF 83 94).
+	{DSI_TRIGGER, DSI_TRIGGER_HOST},
+	{DSI_WR_DATA, 0x2C39},     // MIPI_DSI_DCS_LONG_WRITE: 44 bytes.
+	{DSI_WR_DATA, 0x191919D5}, // Register: 0xD5.
+	{DSI_WR_DATA, 0x19191919},
+	{DSI_WR_DATA, 0x19191919},
+	{DSI_WR_DATA, 0x19191919},
+	{DSI_WR_DATA, 0x19191919},
+	{DSI_WR_DATA, 0x19191919},
+	{DSI_WR_DATA, 0x19191919},
+	{DSI_WR_DATA, 0x19191919},
+	{DSI_WR_DATA, 0x19191919},
+	{DSI_WR_DATA, 0x19191919},
+	{DSI_WR_DATA, 0x19191919},
+	{DSI_TRIGGER, DSI_TRIGGER_HOST},
+	{DSI_WR_DATA, 0x2C39},     // MIPI_DSI_DCS_LONG_WRITE: 44 bytes.
+	{DSI_WR_DATA, 0x191919D6}, // Register: 0xD6.
+	{DSI_WR_DATA, 0x19191919},
+	{DSI_WR_DATA, 0x19191919},
+	{DSI_WR_DATA, 0x19191919},
+	{DSI_WR_DATA, 0x19191919},
+	{DSI_WR_DATA, 0x19191919},
+	{DSI_WR_DATA, 0x19191919},
+	{DSI_WR_DATA, 0x19191919},
+	{DSI_WR_DATA, 0x19191919},
+	{DSI_WR_DATA, 0x19191919},
+	{DSI_WR_DATA, 0x19191919},
+	{DSI_TRIGGER, DSI_TRIGGER_HOST},
+	{DSI_WR_DATA, 0xB39},      // MIPI_DSI_DCS_LONG_WRITE: 11 bytes.
+	{DSI_WR_DATA, 0x711148B1}, // MIPI_DCS_PRIV_SET_POWER_CONTROL. (Not deep standby, BT1 / XDK, VRH gamma volt adj 49 / x40).
+	// (NVRH gamma volt adj 9, Amplifier current small / x30, FS0 freq Fosc/80 / FS1 freq Fosc/32, Enter standby / PON / VCOMG).
+	{DSI_WR_DATA, 0x71143209},
+	{DSI_WR_DATA, 0x114D31},   // (Unknown).
+	{DSI_TRIGGER, DSI_TRIGGER_HOST},
+	{DSI_WR_DATA, 0x439},      // MIPI_DSI_DCS_LONG_WRITE: 4 bytes.
+	{DSI_WR_DATA, 0x000000B9}, // MIPI_DCS_PRIV_SET_EXTC. Disable.
+	{DSI_TRIGGER, DSI_TRIGGER_HOST}
+};
+
+/*
+static const reg_cfg_t _di_init_config_invert[] = {
+	{DSI_WR_DATA, 0x239},
+	{DSI_WR_DATA, 0x02C1}, // INV_EN.
+	{DSI_TRIGGER, DSI_TRIGGER_HOST},
+};
+*/
+
+// Display A Window A one color config.
+static const reg_cfg_t _di_win_one_color[] = {
+	{DC_CMD_DISPLAY_WINDOW_HEADER, WINDOW_A_SELECT | WINDOW_B_SELECT | WINDOW_C_SELECT | WINDOW_D_SELECT},
+	{DC_WIN_WIN_OPTIONS, 0},
+	{DC_DISP_DISP_WIN_OPTIONS, DSI_ENABLE},
+	{DC_CMD_DISPLAY_COMMAND, DISP_CTRL_MODE_C_DISPLAY} // Continuous display.
+};
+
+// Display A Window A linear pitch config.
+static const reg_cfg_t _di_winA_pitch[] = {
+	{DC_CMD_DISPLAY_WINDOW_HEADER, WINDOW_A_SELECT},
+	{DC_WIN_WIN_OPTIONS, 0},
+	{DC_DISP_DISP_WIN_OPTIONS, DSI_ENABLE},
+	{DC_WIN_COLOR_DEPTH, WIN_COLOR_DEPTH_B8G8R8A8}, // NX Default: T_A8B8G8R8, WIN_COLOR_DEPTH_R8G8B8A8.
+	{DC_WIN_POSITION, 0}, //(0,0)
+	{DC_WIN_H_INITIAL_DDA, 0},
+	{DC_WIN_V_INITIAL_DDA, 0},
+	{DC_WIN_PRESCALED_SIZE, V_PRESCALED_SIZE(1280)  | H_PRESCALED_SIZE(720 * 4)},
+	{DC_WIN_DDA_INC,        V_DDA_INC(0x1000)       | H_DDA_INC(0x1000)}, // 1.0x.
+	{DC_WIN_SIZE,           V_SIZE(1280)            | H_SIZE(720)},
+	{DC_WIN_LINE_STRIDE,    UV_LINE_STRIDE(720 * 2) | LINE_STRIDE(720 * 4)}, // 720*2x720*4 (= 0x600 x 0xC00) bytes, see TRM for alignment requirements.
+	{DC_WIN_BUFFER_CONTROL, BUFFER_CONTROL_HOST},
+	{DC_WINBUF_SURFACE_KIND, PITCH},
+	{DC_WINBUF_START_ADDR, IPL_FB_ADDRESS}, // Framebuffer address.
+	{DC_WINBUF_ADDR_H_OFFSET, 0},
+	{DC_WINBUF_ADDR_V_OFFSET, 0},
+	{DC_WIN_WIN_OPTIONS, WIN_ENABLE}, // Enable window AD.
+	{DC_CMD_DISPLAY_COMMAND, DISP_CTRL_MODE_C_DISPLAY}, // Continuous display.
+	{DC_CMD_STATE_CONTROL, GENERAL_UPDATE  | WIN_A_UPDATE},
+	{DC_CMD_STATE_CONTROL, GENERAL_ACT_REQ | WIN_A_ACT_REQ}
+};
+
+// Display A Window A linear pitch + Win D support config.
+static const reg_cfg_t _di_winA_pitch_vic[] = {
+	{DC_CMD_DISPLAY_WINDOW_HEADER, WINDOW_A_SELECT},
+	{DC_WIN_WIN_OPTIONS, 0},
+	{DC_DISP_DISP_WIN_OPTIONS, DSI_ENABLE},
+	{DC_WIN_COLOR_DEPTH, WIN_COLOR_DEPTH_B8G8R8A8}, // NX Default: T_A8B8G8R8, WIN_COLOR_DEPTH_R8G8B8A8.
+	{DC_WIN_POSITION, 0}, //(0,0)
+	{DC_WIN_H_INITIAL_DDA, 0},
+	{DC_WIN_V_INITIAL_DDA, 0},
+	{DC_WIN_PRESCALED_SIZE, V_PRESCALED_SIZE(1280)  | H_PRESCALED_SIZE(720 * 4)},
+	{DC_WIN_DDA_INC,        V_DDA_INC(0x1000)       | H_DDA_INC(0x1000)}, // 1.0x.
+	{DC_WIN_SIZE,           V_SIZE(1280)            | H_SIZE(720)},
+	{DC_WIN_LINE_STRIDE,    UV_LINE_STRIDE(720 * 2) | LINE_STRIDE(720 * 4)}, // 720*2x720*4 (= 0x600 x 0xC00) bytes, see TRM for alignment requirements.
+	{DC_WIN_BUFFER_CONTROL, BUFFER_CONTROL_HOST},
+	{DC_WINBUF_SURFACE_KIND, PITCH},
+	{DC_WINBUF_START_ADDR, NYX_FB_ADDRESS}, // Framebuffer address.
+	{DC_WINBUF_ADDR_H_OFFSET, 0},
+	{DC_WINBUF_ADDR_V_OFFSET, 0},
+	{DC_WIN_WIN_OPTIONS, WIN_ENABLE}, // Enable window AD.
+	{DC_CMD_DISPLAY_COMMAND, DISP_CTRL_MODE_C_DISPLAY}, // Continuous display.
+	{DC_CMD_STATE_CONTROL, GENERAL_UPDATE  | WIN_A_UPDATE},
+	{DC_CMD_STATE_CONTROL, GENERAL_ACT_REQ | WIN_A_ACT_REQ}
+};
+
+// Display A Window A linear pitch inverse + Win D support config.
+static const reg_cfg_t _di_winA_pitch_inv[] = {
+	{DC_CMD_DISPLAY_WINDOW_HEADER, WINDOW_A_SELECT},
+	{DC_WIN_WIN_OPTIONS, 0},
+	{DC_DISP_DISP_WIN_OPTIONS, DSI_ENABLE},
+	{DC_WIN_COLOR_DEPTH, WIN_COLOR_DEPTH_B8G8R8A8}, // NX Default: T_A8B8G8R8, WIN_COLOR_DEPTH_R8G8B8A8.
+	{DC_WIN_POSITION, 0}, //(0,0)
+	{DC_WIN_H_INITIAL_DDA, 0},
+	{DC_WIN_V_INITIAL_DDA, 0},
+	{DC_WIN_PRESCALED_SIZE, V_PRESCALED_SIZE(1280)  | H_PRESCALED_SIZE(720 * 4)},
+	{DC_WIN_DDA_INC,        V_DDA_INC(0x1000)       | H_DDA_INC(0x1000)}, // 1.0x.
+	{DC_WIN_SIZE,           V_SIZE(1280)            | H_SIZE(720)},
+	{DC_WIN_LINE_STRIDE,    UV_LINE_STRIDE(720 * 2) | LINE_STRIDE(720 * 4)}, // 720*2x720*4 (= 0x600 x 0xC00) bytes, see TRM for alignment requirements.
+	{DC_WIN_BUFFER_CONTROL, BUFFER_CONTROL_HOST},
+	{DC_WINBUF_SURFACE_KIND, PITCH},
+	{DC_WINBUF_START_ADDR, NYX_FB_ADDRESS}, // Framebuffer address.
+	{DC_WINBUF_ADDR_H_OFFSET, 0}, // Linear: 0x383FFC, Block: 0x3813FC.
+	{DC_WINBUF_ADDR_V_OFFSET, 1279}, // Linear: 1279, Block: 0.
+	{DC_WIN_WIN_OPTIONS, WIN_ENABLE | V_DIRECTION}, // Enable window AD.
+	{DC_CMD_DISPLAY_COMMAND, DISP_CTRL_MODE_C_DISPLAY}, // Continuous display.
+	{DC_CMD_STATE_CONTROL, GENERAL_UPDATE  | WIN_A_UPDATE},
+	{DC_CMD_STATE_CONTROL, GENERAL_ACT_REQ | WIN_A_ACT_REQ}
+};
+
+// Display A Window A block linear config.
+static const reg_cfg_t _di_winA_block[] = {
+	{DC_CMD_DISPLAY_WINDOW_HEADER, WINDOW_A_SELECT},
+	{DC_WIN_WIN_OPTIONS, 0},
+	{DC_DISP_DISP_WIN_OPTIONS, DSI_ENABLE},
+	{DC_WIN_COLOR_DEPTH, WIN_COLOR_DEPTH_B8G8R8A8}, // NX Default: T_A8B8G8R8, WIN_COLOR_DEPTH_R8G8B8A8.
+	{DC_WIN_POSITION, 0}, //(0,0)
+	{DC_WIN_H_INITIAL_DDA, 0},
+	{DC_WIN_V_INITIAL_DDA, 0},
+	{DC_WIN_PRESCALED_SIZE, V_PRESCALED_SIZE(1280)   | H_PRESCALED_SIZE(720 * 4)},
+	{DC_WIN_DDA_INC,        V_DDA_INC(0x1000)        | H_DDA_INC(0x1000)}, // 1.0x.
+	{DC_WIN_SIZE,           V_SIZE(1280)             | H_SIZE(720)},
+	{DC_WIN_LINE_STRIDE,    UV_LINE_STRIDE(1280 * 2) | LINE_STRIDE(1280 * 4)}, //720*2x720*4 (= 0x600 x 0xC00) bytes, see TRM for alignment requirements.
+	{DC_WIN_BUFFER_CONTROL, BUFFER_CONTROL_HOST},
+	{DC_WINBUF_SURFACE_KIND, BLOCK_HEIGHT(4) | BLOCK},
+	{DC_WINBUF_START_ADDR, NYX_FB_ADDRESS}, // Framebuffer address.
+	{DC_WINBUF_ADDR_H_OFFSET, 0x3813FC}, // Linear: 0x383FFC, Block: 0x3813FC. Block in HOS: 0x13FF.
+	{DC_WINBUF_ADDR_V_OFFSET, 0}, // Linear: 1279, Block: 0.
+	{DC_WIN_WIN_OPTIONS, WIN_ENABLE | SCAN_COLUMN | H_DIRECTION}, // Enable window AD. | SCAN_COLUMN | H_DIRECTION.
+	{DC_CMD_DISPLAY_COMMAND, DISP_CTRL_MODE_C_DISPLAY}, // Continuous display.
+	{DC_CMD_STATE_CONTROL, GENERAL_UPDATE  | WIN_A_UPDATE},
+	{DC_CMD_STATE_CONTROL, GENERAL_ACT_REQ | WIN_A_ACT_REQ}
+};
+
+// Display A Window D config.
+static const reg_cfg_t _di_winD_log[] = {
+	{DC_CMD_DISPLAY_WINDOW_HEADER, WINDOW_D_SELECT},
+	{DC_WIN_WIN_OPTIONS, 0},
+	{DC_WIN_COLOR_DEPTH, WIN_COLOR_DEPTH_B8G8R8A8},
+	{DC_WIN_POSITION, 0}, //(0,0)
+	{DC_WIN_H_INITIAL_DDA, 0},
+	{DC_WIN_V_INITIAL_DDA, 0},
+	{DC_WIN_PRESCALED_SIZE, V_PRESCALED_SIZE(1280)  | H_PRESCALED_SIZE(656 * 4)},
+	{DC_WIN_DDA_INC,        V_DDA_INC(0x1000)       | H_DDA_INC(0x1000)}, // 1.0x.
+	{DC_WIN_SIZE,           V_SIZE(1280)            | H_SIZE(656)},
+	{DC_WIN_LINE_STRIDE,    UV_LINE_STRIDE(656 * 2) | LINE_STRIDE(656 * 4)}, //656*2x656*4 (= 0x600 x 0xC00) bytes, see TRM for alignment requirements.
+	{DC_WIN_BUFFER_CONTROL, BUFFER_CONTROL_HOST},
+	{DC_WINBUF_SURFACE_KIND, PITCH},
+	{DC_WINBUF_START_ADDR, LOG_FB_ADDRESS}, // Framebuffer address.
+	{DC_WINBUF_ADDR_H_OFFSET, 0},
+	{DC_WINBUF_ADDR_V_OFFSET, 0},
+	{DC_WINBUF_BLEND_LAYER_CONTROL, WIN_BLEND_ENABLE | WIN_K1(200) | WIN_BLEND_DEPTH(0)},
+	{DC_WINBUF_BLEND_MATCH_SELECT, WIN_BLEND_FACT_SRC_COLOR_MATCH_SEL_K1 | WIN_BLEND_FACT_DST_COLOR_MATCH_SEL_NEG_K1},
+	{DC_CMD_STATE_CONTROL, GENERAL_UPDATE  | WIN_D_UPDATE},
+	{DC_CMD_STATE_CONTROL, GENERAL_ACT_REQ | WIN_D_ACT_REQ},
+};

bdk/display/vic.c

@@ -0,0 +1,560 @@
+/*
+ * VIC driver for Tegra X1
+ *
+ * Copyright (c) 2018-2024 CTCaer
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <string.h>
+
+#include "vic.h"
+#include <mem/heap.h>
+#include <soc/bpmp.h>
+#include <soc/clock.h>
+#include <soc/timer.h>
+#include <soc/t210.h>
+#include <utils/types.h>
+
+/* VIC Private registers */
+#define PVIC_FALCON_PA_OFFSET 0x1000
+#define PVIC_FALCON_ADDR      0x10AC
+#define PVIC_FALCON_IDLESTATE 0x104C
+
+/* VIC Control and Status registers. */
+/* Fetch Control registers. */
+#define VIC_FC_COMPOSE                         0x10000
+#define  COMPOSE_START                          BIT(0)
+
+#define VIC_FC_CFG_STRUCT_SLOT_INDEX           0x10B00
+
+#define VIC_FC_CFG_STRUCT_SLOT_CFG0            0x10B04
+#define  SLOT_ENABLE                            BIT(0)
+#define  FIELD_CURRENT_ENABLE                   BIT(8)
+
+#define VIC_FC_CFG_STRUCT_SLOT_CFG2            0x10B0C
+#define  CACHE_WIDTH(n) ((n) << 16)
+#define  CACHE_WIDTH_16BX16                     0 // Block Linear.
+#define  CACHE_WIDTH_32BX8                      1 // Block Linear. Recommended for Block Linear.
+#define  CACHE_WIDTH_64BX4                      2 // Block Linear, Pitch. Recommended for Pitch.
+#define  CACHE_WIDTH_128BX2                     3 // Block Linear, Pitch.
+#define  OUTPUT_FLIP_X                          BIT(20)
+#define  OUTPUT_FLIP_Y                          BIT(21)
+#define  OUTPUT_TRANSPOSE                       BIT(22)
+
+#define VIC_FC_CFG_STRUCT_SLOT_SFC_SIZE        0x10B10
+#define VIC_FC_CFG_STRUCT_SLOT_LUMA_SIZE       0x10B14
+#define VIC_FC_CFG_STRUCT_SLOT_CHROMA_SIZE     0x10B18
+#define VIC_FC_CFG_STRUCT_SLOT_SRC_RECT_LR     0x10B1C
+#define VIC_FC_CFG_STRUCT_SLOT_SRC_RECT_TB     0x10B20
+#define VIC_FC_CFG_STRUCT_SLOT_DST_RECT_LR     0x10B30
+#define VIC_FC_CFG_STRUCT_SLOT_DST_RECT_TB     0x10B34
+#define VIC_FC_CFG_STRUCT_TGT_RECT_LR          0x10B38
+#define VIC_FC_CFG_STRUCT_TGT_RECT_TB          0x10B3C
+#define VIC_FC_SLOT_MAP                        0x10C00
+
+#define VIC_FC_FCE_CTRL                        0x11000
+#define  START_TRIGGER                          BIT(0)
+#define  HALT_TRIGGER                           BIT(1)
+#define  CLEAR_ERROR                            BIT(8)
+
+#define VIC_FC_FCE_UCODE_ADDR                  0x11200
+#define VIC_FC_FCE_UCODE_INST                  0x11300
+
+/* Surface List registers. */
+#define VIC_SL_CFG_STRUCT_SLOT_INDEX           0x12100
+#define VIC_SL_CFG_STRUCT_SLOT_DST_RECT_LR     0x12200
+#define VIC_SL_CFG_STRUCT_SLOT_DST_RECT_TB     0x12300
+#define VIC_SL_CFG_STRUCT_TGT_RECT_LR          0x12400
+#define VIC_SL_CFG_STRUCT_TGT_RECT_TB          0x12500
+#define VIC_SL_CFG_STRUCT_SLOT_CFG0            0x12600
+
+/* Surface Cache registers. */
+#define VIC_SC_PRAMBASE                        0x14000
+#define VIC_SC_PRAMSIZE                        0x14100
+#define VIC_SC_SFC0_BASE_LUMA(n)               (0x14300 + (n) * 0x100)
+
+/* Blending Output registers. */
+#define VIC_BL_TARGET_BASADR                   0x22000
+#define VIC_BL_CONFIG                          0x22800
+#define  SUBPARTITION_MODE                      BIT(0)
+#define  PROCESS_CFG_STRUCT_TRIGGER             BIT(2)
+#define  SLOTMASK(n) ((n) << 8)
+
+#define VIC_BL_CFG_STRUCT_CFG0                 0x22C00
+#define VIC_BL_CFG_STRUCT_SFC_SIZE             0x22C04
+#define VIC_BL_CFG_STRUCT_LUMA_SIZE            0x22C08
+#define VIC_BL_CFG_STRUCT_CHROMA_SIZE          0x22C0C
+#define VIC_BL_CFG_STRUCT_TGT_RECT_LR          0x22C10
+#define VIC_BL_CFG_STRUCT_TGT_RECT_TB          0x22C14
+
+// VIC_FC_CFG_STRUCT_SLOT_CFG2 & VIC_BL_CFG_STRUCT_CFG0.
+#define BLK_KIND(n)    ((n) << 8)
+#define  BLK_KIND_PITCH          0
+#define  BLK_KIND_GENERIC_16BX2  1
+#define BLK_HEIGHT(n)  ((n) << 12)
+#define  BLK_HEIGHT_ONE_GOB      0
+#define  BLK_HEIGHT_SIXTEEN_GOBS 4
+
+// Generic size macros.
+#define SIZE_WIDTH(n)  (((n) - 1) << 0)
+#define SIZE_HEIGHT(n) (((n) - 1) << 16)
+#define RECT_LEFT(n)   ((n) << 0)
+#define RECT_RIGHT(n)  (((n) - 1) << 16)
+#define RECT_TOP(n)    ((n) << 0)
+#define RECT_BOTTOM(n) (((n) - 1) << 16)
+
+#define FORMAT_PROGRESSIVE 0
+#define SOFT_CLAMP_MIN     0
+#define SOFT_CLAMP_MAX     0x3FFu
+#define ALPHA_1_0          0x3FFu
+
+typedef struct _OutputConfig {
+	u64 AlphaFillMode:3;
+	u64 AlphaFillSlot:3;
+	u64 BackgroundAlpha:10;
+	u64 BackgroundR:10;
+	u64 BackgroundG:10;
+	u64 BackgroundB:10;
+	u64 RegammaMode:2;
+	u64 OutputFlipX:1;
+	u64 OutputFlipY:1;
+	u64 OutputTranspose:1;
+	u64 rsvd1:1;
+	u64 rsvd2:12;
+	u64 TargetRectLeft:14;
+	u64 rsvd3:2;
+	u64 TargetRectRight:14;
+	u64 rsvd4:2;
+	u64 TargetRectTop:14;
+	u64 rsvd5:2;
+	u64 TargetRectBottom:14;
+	u64 rsvd6:2;
+} OutputConfig;
+
+typedef struct _OutputSurfaceConfig {
+	u64 OutPixelFormat:7;
+	u64 OutChromaLocHoriz:2;
+	u64 OutChromaLocVert:2;
+	u64 OutBlkKind:4;
+	u64 OutBlkHeight:4;
+	u64 rsvd0:3;
+	u64 rsvd1:10;
+	u64 OutSurfaceWidth:14;
+	u64 OutSurfaceHeight:14;
+	u64 rsvd2:4;
+	u64 OutLumaWidth:14;
+	u64 OutLumaHeight:14;
+	u64 rsvd3:4;
+	u64 OutChromaWidth:14;
+	u64 OutChromaHeight:14;
+	u64 rsvd4:4;
+} OutputSurfaceConfig;
+
+typedef struct _SlotConfig {
+	u64 SlotEnable:1;
+	u64 DeNoise:1;
+	u64 AdvancedDenoise:1;
+	u64 CadenceDetect:1;
+	u64 MotionMap:1;
+	u64 MMapCombine:1;
+	u64 IsEven:1;
+	u64 ChromaEven:1;
+	u64 CurrentFieldEnable:1;
+	u64 PrevFieldEnable:1;
+	u64 NextFieldEnable:1;
+	u64 NextNrFieldEnable:1;
+	u64 CurMotionFieldEnable:1;
+	u64 PrevMotionFieldEnable:1;
+	u64 PpMotionFieldEnable:1;
+	u64 CombMotionFieldEnable:1;
+	u64 FrameFormat:4;
+	u64 FilterLengthY:2;
+	u64 FilterLengthX:2;
+	u64 Panoramic:12;
+	u64 rsvd1:22;
+	u64 DetailFltClamp:6;
+	u64 FilterNoise:10;
+	u64 FilterDetail:10;
+	u64 ChromaNoise:10;
+	u64 ChromaDetail:10;
+	u64 DeinterlaceMode:4;
+	u64 MotionAccumWeight:3;
+	u64 NoiseIir:11;
+	u64 LightLevel:4;
+	u64 rsvd4:2;
+	u64 SoftClampLow:10;
+	u64 SoftClampHigh:10;
+	u64 rsvd5:3;
+	u64 rsvd6:9;
+	u64 PlanarAlpha:10;
+	u64 ConstantAlpha:1;
+	u64 StereoInterleave:3;
+	u64 ClipEnabled:1;
+	u64 ClearRectMask:8;
+	u64 DegammaMode:2;
+	u64 rsvd7:1;
+	u64 DecompressEnable:1;
+	u64 rsvd9:5;
+	u64 DecompressCtbCount:8;
+	u64 DecompressZbcColor:32;
+	u64 rsvd12:24;
+	u64 SourceRectLeft:30;
+	u64 rsvd14:2;
+	u64 SourceRectRight:30;
+	u64 rsvd15:2;
+	u64 SourceRectTop:30;
+	u64 rsvd16:2;
+	u64 SourceRectBottom:30;
+	u64 rsvd17:2;
+	u64 DestRectLeft:14;
+	u64 rsvd18:2;
+	u64 DestRectRight:14;
+	u64 rsvd19:2;
+	u64 DestRectTop:14;
+	u64 rsvd20:2;
+	u64 DestRectBottom:14;
+	u64 rsvd21:2;
+	u64 rsvd22:32;
+	u64 rsvd23:32;
+} SlotConfig;
+
+typedef struct _SlotSurfaceConfig {
+	u64 SlotPixelFormat:7;
+	u64 SlotChromaLocHoriz:2;
+	u64 SlotChromaLocVert:2;
+	u64 SlotBlkKind:4;
+	u64 SlotBlkHeight:4;
+	u64 SlotCacheWidth:3;
+	u64 rsvd0:10;
+	u64 SlotSurfaceWidth:14;
+	u64 SlotSurfaceHeight:14;
+	u64 rsvd1:4;
+	u64 SlotLumaWidth:14;
+	u64 SlotLumaHeight:14;
+	u64 rsvd2:4;
+	u64 SlotChromaWidth:14;
+	u64 SlotChromaHeight:14;
+	u64 rsvd3:4;
+} SlotSurfaceConfig;
+
+typedef struct _SlotStruct {
+	SlotConfig slot_cfg;
+	SlotSurfaceConfig slot_sfc_cfg;
+
+	// No need to configure. Reset to zeros.
+	u8 lumaKeyStruct[0x10];
+	u8 colorMatrixStruct[0x20];
+	u8 gamutMatrixStruct[0x20];
+	u8 blendingSlotStruct[0x10];
+} SlotStruct;
+
+typedef struct _vic_config_t {
+	// No need to configure. Reset to zeros.
+	u8 pipeConfig[0x10];
+
+	OutputConfig out_cfg;
+	OutputSurfaceConfig out_sfc_cfg;
+
+	// No need to configure. Reset to zeros.
+	u8 out_color_matrix[0x20];
+	u8 clear_rect[0x10 * 4];
+
+	SlotStruct slots[8];
+} vic_config_t;
+
+// VIC Fetch Control Engine microcode. Dumped from L4T r33.
+u8 vic_fce_ucode[] = {
+	0x66, 0x00, 0x00, 0x00, 0x60, 0x07, 0x00, 0x00, 0x42, 0x40, 0x10, 0x00, 0x4E, 0x01, 0x40, 0x00,
+	0x6A, 0x07, 0x00, 0x00, 0x6E, 0x23, 0x04, 0x00, 0x6C, 0x00, 0x00, 0x00, 0x4E, 0x01, 0x04, 0x00,
+	0x6A, 0x0B, 0x00, 0x00, 0x6E, 0x1F, 0x04, 0x00, 0x6C, 0x00, 0x00, 0x00, 0x4E, 0x01, 0x10, 0x00,
+	0x6A, 0x0F, 0x00, 0x00, 0x6E, 0x1F, 0x04, 0x00, 0x6C, 0x00, 0x00, 0x00, 0x48, 0x80, 0x02, 0x00,
+	0x0E, 0x11, 0x00, 0x00, 0x6A, 0x14, 0x00, 0x00, 0x6E, 0x08, 0x06, 0x00, 0x6C, 0x00, 0x00, 0x00,
+	0x4E, 0x01, 0x08, 0x00, 0x6A, 0x18, 0x00, 0x00, 0x6E, 0x26, 0x04, 0x00, 0x6C, 0x00, 0x00, 0x00,
+	0x4E, 0x01, 0x20, 0x00, 0x6A, 0x1C, 0x00, 0x00, 0x6E, 0x26, 0x04, 0x00, 0x6C, 0x00, 0x00, 0x00,
+	0x4E, 0x01, 0x02, 0x00, 0x6A, 0x20, 0x00, 0x00, 0x6E, 0x24, 0x00, 0x00, 0x6C, 0x00, 0x00, 0x00,
+	0x56, 0x00, 0x10, 0x00, 0x56, 0x40, 0x10, 0x00, 0x22, 0x41, 0x01, 0x00, 0x6C, 0x00, 0x00, 0x00,
+	0x62, 0x80, 0x01, 0x00, 0x60, 0x47, 0x00, 0x00, 0x60, 0x87, 0x00, 0x00, 0x01, 0x4A, 0x00, 0x00,
+	0x55, 0xC0, 0x20, 0x00, 0x00, 0x59, 0x00, 0x00, 0x60, 0x87, 0x00, 0x00, 0x60, 0xC7, 0x00, 0x00,
+	0x01, 0x93, 0x00, 0x00, 0x40, 0x82, 0x02, 0x00, 0x4E, 0x02, 0x00, 0x00, 0x6B, 0x34, 0x00, 0x00,
+	0x43, 0xC1, 0x10, 0x00, 0x42, 0x02, 0x03, 0x00, 0x00, 0x23, 0x01, 0x00, 0x24, 0xD4, 0x00, 0x00,
+	0x56, 0x40, 0x3D, 0x00, 0x04, 0xEB, 0x00, 0x00, 0x60, 0x07, 0x01, 0x00, 0x60, 0x47, 0x00, 0x00,
+	0x6A, 0x3E, 0x00, 0x00, 0x55, 0xC0, 0x30, 0x00, 0x48, 0x00, 0x01, 0x00, 0x48, 0x40, 0x01, 0x00,
+	0x48, 0x80, 0x01, 0x00, 0x6B, 0x28, 0x02, 0x00, 0x56, 0x40, 0x09, 0x00, 0x04, 0x4D, 0x01, 0x00,
+	0x06, 0x4D, 0x00, 0x00, 0x42, 0xC0, 0x03, 0x00, 0x56, 0x80, 0x09, 0x00, 0x04, 0xFE, 0x01, 0x00,
+	0x00, 0xF9, 0x01, 0x00, 0x4E, 0x02, 0x00, 0x00, 0x6B, 0x32, 0x02, 0x00, 0x55, 0x40, 0x2F, 0x00,
+	0x56, 0x80, 0x0D, 0x00, 0x4F, 0x00, 0x00, 0x00, 0x6A, 0x0D, 0x02, 0x00, 0x55, 0x40, 0x31, 0x00,
+	0x56, 0x80, 0x0B, 0x00, 0x0C, 0x2B, 0x00, 0x00, 0x6A, 0x13, 0x02, 0x00, 0x43, 0x45, 0x03, 0x00,
+	0x42, 0x86, 0x03, 0x00, 0x4D, 0x06, 0x02, 0x00, 0x6A, 0x0D, 0x02, 0x00, 0x42, 0x86, 0x03, 0x00,
+	0x22, 0x7E, 0x01, 0x00, 0x4E, 0x04, 0x00, 0x00, 0x6B, 0x32, 0x02, 0x00, 0x55, 0x40, 0x17, 0x00,
+	0x0D, 0x2C, 0x00, 0x00, 0x56, 0xC0, 0x09, 0x00, 0x6A, 0x1E, 0x02, 0x00, 0x48, 0xC0, 0x01, 0x00,
+	0x43, 0x04, 0x03, 0x00, 0x6C, 0x20, 0x02, 0x00, 0x55, 0x40, 0x19, 0x00, 0x01, 0x2C, 0x01, 0x00,
+	0x65, 0x23, 0x01, 0x00, 0x42, 0x42, 0x03, 0x00, 0x00, 0x2C, 0x01, 0x00, 0x24, 0x14, 0x01, 0x00,
+	0x00, 0x2C, 0x01, 0x00, 0x24, 0x14, 0x01, 0x00, 0x00, 0x3C, 0x01, 0x00, 0x42, 0x04, 0x09, 0x00,
+	0x42, 0xC3, 0x02, 0x00, 0x65, 0x54, 0x01, 0x00, 0x65, 0x55, 0x01, 0x00, 0x42, 0x45, 0x0D, 0x00,
+	0x62, 0x03, 0x00, 0x00, 0x62, 0x44, 0x00, 0x00, 0x62, 0x85, 0x00, 0x00, 0x62, 0xC2, 0x00, 0x00,
+	0x22, 0x48, 0x1F, 0x00, 0x6F, 0x00, 0x00, 0x00, 0x48, 0x00, 0x01, 0x00, 0x6C, 0x28, 0x02, 0x00,
+	0x62, 0x80, 0x01, 0x00, 0x60, 0x07, 0x00, 0x00, 0x60, 0x47, 0x00, 0x00, 0x60, 0x87, 0x00, 0x00,
+	0x01, 0x01, 0x00, 0x00, 0x43, 0x00, 0x02, 0x00, 0x40, 0x00, 0x02, 0x00, 0x01, 0xCA, 0x01, 0x00,
+	0x60, 0x03, 0x01, 0x00, 0x01, 0xA0, 0x01, 0x00, 0x60, 0x40, 0x00, 0x00, 0x65, 0x01, 0x00, 0x00,
+	0x55, 0xC0, 0x2E, 0x00, 0x01, 0x18, 0x00, 0x00, 0x43, 0x00, 0x04, 0x00, 0x43, 0x41, 0x06, 0x00,
+	0x6F, 0x00, 0x00, 0x00, 0x61, 0xC1, 0x00, 0x00, 0x61, 0x42, 0x01, 0x00, 0x65, 0xB5, 0x00, 0x00,
+	0x65, 0x73, 0x01, 0x00, 0x65, 0x35, 0x01, 0x00, 0x65, 0x34, 0x01, 0x00, 0x42, 0x04, 0x0D, 0x00,
+	0x01, 0x14, 0x01, 0x00, 0x42, 0x04, 0x03, 0x00, 0x00, 0x20, 0x00, 0x00, 0x43, 0x03, 0x05, 0x00,
+	0x43, 0x85, 0x02, 0x00, 0x00, 0xAA, 0x00, 0x00, 0x48, 0x46, 0x01, 0x00, 0x65, 0xEB, 0x00, 0x00,
+	0x00, 0x9A, 0x00, 0x00, 0x65, 0xB2, 0x01, 0x00, 0x00, 0xA6, 0x01, 0x00, 0x42, 0x86, 0x0D, 0x00,
+	0x61, 0x42, 0x01, 0x00, 0x01, 0xAE, 0x01, 0x00, 0x00, 0x71, 0x00, 0x00, 0x42, 0x82, 0x08, 0x00,
+	0x42, 0xC3, 0x08, 0x00, 0x48, 0x40, 0x01, 0x00, 0x6F, 0x00, 0x00, 0x00, 0x6E, 0x34, 0x02, 0x00,
+	0x65, 0x79, 0x00, 0x00, 0x00, 0x48, 0x00, 0x00, 0x6C, 0x36, 0x04, 0x00, 0x6E, 0x34, 0x02, 0x00,
+	0x48, 0x7F, 0x01, 0x00, 0x6C, 0x0A, 0x06, 0x00, 0x6E, 0x34, 0x02, 0x00, 0x6E, 0x05, 0x04, 0x00,
+	0x65, 0x79, 0x00, 0x00, 0x00, 0x48, 0x00, 0x00, 0x41, 0x87, 0x03, 0x00, 0x65, 0xBA, 0x00, 0x00,
+	0x65, 0xB2, 0x00, 0x00, 0x42, 0x82, 0x02, 0x00, 0x00, 0x51, 0x00, 0x00, 0x61, 0xC1, 0x00, 0x00,
+	0x65, 0xFB, 0x00, 0x00, 0x65, 0xF3, 0x00, 0x00, 0x41, 0x87, 0x05, 0x00, 0x65, 0xF3, 0x00, 0x00,
+	0x42, 0xC3, 0x08, 0x00, 0x00, 0x59, 0x00, 0x00, 0x60, 0xC7, 0x00, 0x00, 0x60, 0xC7, 0x00, 0x00,
+	0x56, 0xC0, 0x21, 0x00, 0x04, 0xDF, 0x01, 0x00, 0x43, 0xC7, 0x15, 0x00, 0x00, 0x38, 0x00, 0x00,
+	0x00, 0x79, 0x00, 0x00, 0x42, 0xC3, 0x20, 0x00, 0x43, 0xC3, 0x04, 0x00, 0x42, 0x00, 0x30, 0x00,
+	0x42, 0x41, 0x30, 0x00, 0x00, 0x03, 0x00, 0x00, 0x00, 0x4B, 0x00, 0x00, 0x60, 0xC7, 0x01, 0x00,
+	0x22, 0x78, 0x01, 0x00, 0x22, 0x79, 0x03, 0x00, 0x22, 0x7F, 0x1F, 0x00, 0x6F, 0x00, 0x00, 0x00,
+	0x6E, 0x34, 0x02, 0x00, 0x6E, 0x05, 0x04, 0x00, 0x4B, 0x41, 0x00, 0x00, 0x60, 0xC7, 0x01, 0x00,
+	0x60, 0x87, 0x01, 0x00, 0x43, 0x86, 0x15, 0x00, 0x00, 0x30, 0x00, 0x00, 0x65, 0x39, 0x01, 0x00,
+	0x42, 0x04, 0x05, 0x00, 0x4E, 0x05, 0x7E, 0x00, 0x6A, 0x1B, 0x06, 0x00, 0x55, 0xC0, 0x3D, 0x00,
+	0x0A, 0x3C, 0x01, 0x00, 0x60, 0xC7, 0x01, 0x00, 0x22, 0x78, 0x01, 0x00, 0x22, 0x79, 0x03, 0x00,
+	0x22, 0x7C, 0x09, 0x00, 0x22, 0x7F, 0x1F, 0x00, 0x6F, 0x00, 0x00, 0x00, 0x65, 0x7A, 0x01, 0x00,
+	0x42, 0x45, 0x05, 0x00, 0x65, 0xBB, 0x01, 0x00, 0x42, 0x86, 0x05, 0x00, 0x55, 0xC0, 0x3D, 0x00,
+	0x0A, 0x7D, 0x01, 0x00, 0x0A, 0xBE, 0x01, 0x00, 0x07, 0xC7, 0x01, 0x00, 0x0B, 0x7D, 0x01, 0x00,
+	0x0B, 0xBE, 0x01, 0x00, 0x55, 0xC0, 0x3D, 0x00, 0x0A, 0x3C, 0x01, 0x00, 0x60, 0xC7, 0x01, 0x00,
+	0x22, 0x78, 0x01, 0x00, 0x22, 0x79, 0x03, 0x00, 0x22, 0x7A, 0x05, 0x00, 0x22, 0x7B, 0x07, 0x00,
+	0x22, 0x7C, 0x09, 0x00, 0x22, 0x7D, 0x0B, 0x00, 0x22, 0x7E, 0x0D, 0x00, 0x22, 0x7F, 0x1F, 0x00,
+	0x6F, 0x00, 0x00, 0x00
+};
+
+vic_config_t __attribute__((aligned (0x100))) vic_cfg = {0};
+
+u32 _vic_read_priv(u32 addr)
+{
+	u32 addr_lsb = addr & 0xFF;
+
+	// Set address LSB.
+	if (addr_lsb)
+		VIC(PVIC_FALCON_ADDR) = addr_lsb >> 2;
+
+	// Set address.
+	u32 val = VIC(PVIC_FALCON_PA_OFFSET + (addr >> 6));
+
+	// Unset address LSB.
+	if (addr_lsb)
+		VIC(PVIC_FALCON_ADDR) = 0;
+
+	return val;
+}
+
+static void _vic_write_priv(u32 addr, u32 data)
+{
+	u32 addr_lsb = addr & 0xFF;
+
+	// Set address LSB.
+	if (addr_lsb)
+		VIC(PVIC_FALCON_ADDR) = addr_lsb >> 2;
+
+	// Set address.
+	VIC(PVIC_FALCON_PA_OFFSET + (addr >> 6)) = data;
+
+	// Unset address LSB.
+	if (addr_lsb)
+		VIC(PVIC_FALCON_ADDR) = 0;
+}
+
+static int _vic_wait_idle()
+{
+	u32 timeout_count = 15000; // 150ms.
+
+	while (VIC(PVIC_FALCON_IDLESTATE))
+	{
+		usleep(10);
+
+		timeout_count--;
+		if (!timeout_count)
+			return -1;
+	};
+
+	return 0;
+}
+
+void vic_set_surface(const vic_surface_t *sfc)
+{
+	u32 flip_x  = 0;
+	u32 flip_y  = 0;
+	u32 swap_xy = 0;
+	u32 const_alpha = 0;
+
+	u32 width   = sfc->width;
+	u32 height  = sfc->height;
+	u32 pix_fmt = sfc->pix_fmt;
+	u32 src_buf = sfc->src_buf;
+	u32 dst_buf = sfc->dst_buf;
+
+	// Get format alpha type.
+	switch (sfc->pix_fmt)
+	{
+	case VIC_PIX_FORMAT_L8:
+	case VIC_PIX_FORMAT_X1B5G5R5:
+	case VIC_PIX_FORMAT_B5G5R5X1:
+	case VIC_PIX_FORMAT_X8B8G8R8:
+	case VIC_PIX_FORMAT_X8R8G8B8:
+	case VIC_PIX_FORMAT_B8G8R8X8:
+	case VIC_PIX_FORMAT_R8G8B8X8:
+		const_alpha = 1;
+		break;
+
+	case VIC_PIX_FORMAT_A8B8G8R8:
+	case VIC_PIX_FORMAT_A8R8G8B8:
+	case VIC_PIX_FORMAT_B8G8R8A8:
+	case VIC_PIX_FORMAT_R8G8B8A8:
+	default:
+		break;
+	}
+
+	// Get rotation parameters.
+	switch (sfc->rotation)
+	{
+	case VIC_ROTATION_90:
+		swap_xy = 1;
+		break;
+
+	case VIC_ROTATION_180:
+		flip_x  = 1;
+		flip_y  = 1;
+		break;
+
+	case VIC_ROTATION_270:
+		flip_x  = 1;
+		swap_xy = 1;
+		break;
+
+	case VIC_ROTATION_0:
+	default:
+		break;
+	}
+
+	// Set output surface format.
+	vic_cfg.out_sfc_cfg.OutPixelFormat = pix_fmt;
+	vic_cfg.out_sfc_cfg.OutBlkKind     = BLK_KIND_PITCH;
+	vic_cfg.out_sfc_cfg.OutBlkHeight   = 0;
+
+	// Set output rotation/flip.
+	vic_cfg.out_cfg.OutputFlipX     = flip_x;
+	vic_cfg.out_cfg.OutputFlipY     = flip_y;
+	vic_cfg.out_cfg.OutputTranspose = swap_xy;
+
+	// Set output surface resolution.
+	vic_cfg.out_sfc_cfg.OutSurfaceWidth  = width  - 1;
+	vic_cfg.out_sfc_cfg.OutSurfaceHeight = height - 1;
+	vic_cfg.out_sfc_cfg.OutLumaWidth     = width  - 1;
+	vic_cfg.out_sfc_cfg.OutLumaHeight    = height - 1;
+
+	// Set output destination rectangle. Anything outside will not be touched at output buffer.
+	vic_cfg.out_cfg.TargetRectLeft   = 0;
+	vic_cfg.out_cfg.TargetRectRight  = width - 1;
+	vic_cfg.out_cfg.TargetRectTop    = 0;
+	vic_cfg.out_cfg.TargetRectBottom = height - 1;
+
+	// Initialize slot parameters.
+	vic_cfg.slots[0].slot_cfg.SlotEnable    = 1;
+	vic_cfg.slots[0].slot_cfg.SoftClampLow  = SOFT_CLAMP_MIN;
+	vic_cfg.slots[0].slot_cfg.SoftClampHigh = SOFT_CLAMP_MAX;
+	vic_cfg.slots[0].slot_cfg.PlanarAlpha   = ALPHA_1_0;
+	vic_cfg.slots[0].slot_cfg.ConstantAlpha = const_alpha;
+	vic_cfg.slots[0].slot_cfg.FrameFormat   = FORMAT_PROGRESSIVE;
+
+	// Set input source rectangle.
+	vic_cfg.slots[0].slot_cfg.SourceRectLeft   = 0;
+	vic_cfg.slots[0].slot_cfg.SourceRectRight  = (width  - 1) << 16;
+	vic_cfg.slots[0].slot_cfg.SourceRectTop    = 0;
+	vic_cfg.slots[0].slot_cfg.SourceRectBottom = (height - 1) << 16;
+
+	// Set input destination rectangle.
+	vic_cfg.slots[0].slot_cfg.DestRectLeft   = 0;
+	vic_cfg.slots[0].slot_cfg.DestRectRight  = (width  - 1);
+	vic_cfg.slots[0].slot_cfg.DestRectTop    = 0;
+	vic_cfg.slots[0].slot_cfg.DestRectBottom = (height - 1);
+
+	// Set input surface format.
+	vic_cfg.slots[0].slot_sfc_cfg.SlotPixelFormat = pix_fmt;
+	vic_cfg.slots[0].slot_sfc_cfg.SlotBlkKind     = BLK_KIND_PITCH;
+	vic_cfg.slots[0].slot_sfc_cfg.SlotBlkHeight   = 0;
+	vic_cfg.slots[0].slot_sfc_cfg.SlotCacheWidth  = CACHE_WIDTH_64BX4;
+
+	// Set input surface resolution.
+	vic_cfg.slots[0].slot_sfc_cfg.SlotSurfaceWidth  = width  - 1;
+	vic_cfg.slots[0].slot_sfc_cfg.SlotSurfaceHeight = height - 1;
+	vic_cfg.slots[0].slot_sfc_cfg.SlotLumaWidth     = width  - 1;
+	vic_cfg.slots[0].slot_sfc_cfg.SlotLumaHeight    = height - 1;
+
+	// Flush data.
+	bpmp_mmu_maintenance(BPMP_MMU_MAINT_CLEAN_WAY, false);
+
+	// Set parameters base and size. Causes a parse by surface cache.
+	_vic_write_priv(VIC_SC_PRAMBASE, (u32)&vic_cfg >> 8);
+	_vic_write_priv(VIC_SC_PRAMSIZE, sizeof(vic_config_t) >> 6);
+
+	// Wait for surface cache to get ready.
+	_vic_wait_idle();
+
+	// Set slot mapping.
+	_vic_write_priv(VIC_FC_SLOT_MAP, 0xFFFFFFF0);
+
+	// Set input surface buffer.
+	_vic_write_priv(VIC_SC_SFC0_BASE_LUMA(0), src_buf >> 8);
+
+	// Set output surface buffer.
+	_vic_write_priv(VIC_BL_TARGET_BASADR, dst_buf >> 8);
+
+	// Set blending config and push changes to surface cache.
+	_vic_write_priv(VIC_BL_CONFIG, SLOTMASK(0x1F) | PROCESS_CFG_STRUCT_TRIGGER | SUBPARTITION_MODE);
+
+	// Wait for surface cache to get ready.
+	_vic_wait_idle();
+}
+
+int vic_compose()
+{
+	// Wait for surface cache to get ready. Otherwise VIC will hang.
+	int res = _vic_wait_idle();
+
+	// Start composition of a single frame.
+	_vic_write_priv(VIC_FC_COMPOSE, COMPOSE_START);
+
+	return res;
+}
+
+int vic_init()
+{
+	clock_enable_vic();
+
+	// Load Fetch Control Engine microcode.
+	for (u32 i = 0; i < sizeof(vic_fce_ucode) / sizeof(u32); i++)
+	{
+		_vic_write_priv(VIC_FC_FCE_UCODE_ADDR, (i * sizeof(u32)));
+		_vic_write_priv(VIC_FC_FCE_UCODE_INST, *(u32 *)&vic_fce_ucode[i * sizeof(u32)]);
+	}
+
+	// Start Fetch Control Engine.
+	_vic_write_priv(VIC_FC_FCE_CTRL, START_TRIGGER);
+
+	return _vic_wait_idle();
+}
+
+void vic_end()
+{
+	clock_disable_vic();
+}

bdk/display/vic.h

@@ -0,0 +1,66 @@
+/*
+ * VIC driver for Tegra X1
+ *
+ * Copyright (c) 2018-2019 CTCaer
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef _VIC_H_
+#define _VIC_H_
+
+#include <utils/types.h>
+
+#define VIC_THI_SLCG_OVERRIDE_LOW_A 0x8C
+
+typedef enum _vic_rotation_t
+{
+	VIC_ROTATION_0   = 0,
+	VIC_ROTATION_90  = 1,
+	VIC_ROTATION_180 = 2,
+	VIC_ROTATION_270 = 3,
+} vic_rotation_t;
+
+typedef enum _vic_pix_format_t
+{
+	VIC_PIX_FORMAT_L8       =  1, //  8-bit LUT.
+	VIC_PIX_FORMAT_X1B5G5R5 = 21, // 16-bit XBGR.
+	VIC_PIX_FORMAT_B5G5R5X1 = 23, // 16-bit BGRX.
+
+	VIC_PIX_FORMAT_A8B8G8R8 = 31, // 32-bit ABGR.
+	VIC_PIX_FORMAT_A8R8G8B8 = 32, // 32-bit ARGB.
+	VIC_PIX_FORMAT_B8G8R8A8 = 33, // 32-bit BGRA.
+	VIC_PIX_FORMAT_R8G8B8A8 = 34, // 32-bit RGBA.
+
+	VIC_PIX_FORMAT_X8B8G8R8 = 35, // 32-bit XBGR.
+	VIC_PIX_FORMAT_X8R8G8B8 = 36, // 32-bit XRGB.
+	VIC_PIX_FORMAT_B8G8R8X8 = 37, // 32-bit BGRX.
+	VIC_PIX_FORMAT_R8G8B8X8 = 38, // 32-bit RGBX.
+} vic_pix_format_t;
+
+typedef struct _vic_surface_t
+{
+	u32 src_buf;
+	u32 dst_buf;
+	u32 width;
+	u32 height;
+	u32 pix_fmt;
+	u32 rotation;
+} vic_surface_t;
+
+void vic_set_surface(const vic_surface_t *sfc);
+int  vic_compose();
+int  vic_init();
+void vic_end();
+
+#endif

bdk/exception_handlers.S

@@ -0,0 +1,239 @@
+/*
+ * Copyright (c) 2019 CTCaer
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * Armv7tdmi Status register.
+ *
+ * bit0: Mode 0.
+ * bit1: Mode 1.
+ * bit2: Mode 2.
+ * bit3: Mode 3.
+ * bit4: Mode 4.
+ * bit5: Thumb state.
+ * bit6: FIQ disable.
+ * bit7: IRQ disable.
+ * bit8-27: Reserved.
+ * bit28: Overflow condition.
+ * bit29: Carry/Borrow/Extend condition.
+ * bit30: Zero condition.
+ * bit31: Negative/Less than condition.
+ *
+ * M[4:0] | Mode | Visible Thumb-state registers             | Visible ARM-state registers
+ * 10000  | USER | r0–r7, SP,     LR,     PC, CPSR           | r0–r14,                   PC, CPSR
+ * 10001  | FIQ  | r0–r7, SP_fiq, LR_fiq, PC, CPSR, SPSR_fiq | r0–r7,  r8_fiq–r14_fiq,   PC, CPSR, SPSR_fiq
+ * 10010  | IRQ  | r0–r7, SP_irq, LR_irq, PC, CPSR, SPSR_irq | r0–r12, r13_irq, r14_irq, PC, CPSR, SPSR_irq
+ * 10011  | SVC  | r0–r7, SP_svc, LR_svc, PC, CPSR, SPSR_svc | r0–r12, r13_svc, r14_svc, PC, CPSR, SPSR_svc
+ * 10111  | ABRT | r0–r7, SP_abt, LR_abt, PC, CPSR, SPSR_abt | r0–r12, r13_abt, r14_abt, PC, CPSR, SPSR_abt
+ * 11011  | UNDF | r0–r7, SP_und, LR_und, PC, CPSR, SPSR_und | r0–r12, r13_und, r14_und, PC, CPSR, SPSR_und
+ * 11111  | SYS  | r0–r7, SP,     LR,     PC, CPSR           | r0–r14,                   PC, CPSR
+ */
+
+#define EXCP_EN_ADDR   0x4003FFFC
+#define EXCP_TYPE_ADDR 0x4003FFF8
+#define EXCP_LR_ADDR   0x4003FFF4
+
+#define EXCP_VEC_BASE  0x6000F000
+#define EVP_COP_RESET_VECTOR          0x200
+#define EVP_COP_UNDEF_VECTOR          0x204
+#define EVP_COP_SWI_VECTOR            0x208
+#define EVP_COP_PREFETCH_ABORT_VECTOR 0x20C
+#define EVP_COP_DATA_ABORT_VECTOR     0x210
+#define EVP_COP_RSVD_VECTOR           0x214
+#define EVP_COP_IRQ_VECTOR            0x218
+#define EVP_COP_FIQ_VECTOR            0x21C
+
+#define MODE_USR  0x10
+#define MODE_FIQ  0x11
+#define MODE_IRQ  0x12
+#define MODE_SVC  0x13
+#define MODE_ABT  0x17
+#define MODE_UDF  0x1B
+#define MODE_SYS  0x1F
+#define MODE_MASK 0x1F
+
+#define FIQ 0x40
+#define IRQ 0x80
+
+.section .text._irq_setup
+.arm
+
+.extern ipl_main
+.type ipl_main, %function
+
+.extern svc_handler
+.type svc_handler, %function
+
+.extern irq_handler
+.type irq_handler, %function
+
+.extern fiq_setup
+.type fiq_setup, %function
+
+.extern fiq_handler
+.type fiq_handler, %function
+
+.globl _irq_setup
+.type _irq_setup, %function
+_irq_setup:
+	MRS R0, CPSR
+	BIC R0, R0, #MODE_MASK              /* Clear mode bits */
+	ORR R0, R0, #(MODE_SVC | IRQ | FIQ) /* SUPERVISOR mode, IRQ/FIQ disabled */
+	MSR CPSR, R0
+
+	/* Setup IRQ stack pointer */
+	MSR CPSR, #(MODE_IRQ | IRQ | FIQ) /* IRQ mode, IRQ/FIQ disabled */
+	LDR SP, =0x40040000
+
+	/* Setup FIQ stack pointer */
+	MSR CPSR, #(MODE_FIQ | IRQ | FIQ) /* FIQ mode, IRQ/FIQ disabled */
+	LDR SP, =0x40040000
+
+	/* Setup SYS stack pointer */
+	MSR CPSR, #(MODE_SYS | IRQ | FIQ) /* SYSTEM mode, IRQ/FIQ disabled */
+	LDR SP, =0x4003FF00               /* Will be changed later to DRAM */
+
+	MOV LR, PC
+	BL setup_vectors
+	/*BL fiq_setup*/
+
+	/* Enable interrupts */
+	BL irq_enable_cpu_irq_exceptions
+
+	B ipl_main
+	B .
+
+.globl excp_reset
+.type excp_reset, %function
+excp_reset:
+	LDR R0, =EXCP_EN_ADDR
+	LDR R1, =0x30505645 /* EVP0 */
+	STR R1, [R0]        /* EVP0 in EXCP_EN_ADDR */
+	LDR R0, =EXCP_LR_ADDR
+	MOV R1, LR
+	STR R1, [R0]        /* Save LR in EXCP_LR_ADDR */
+	LDR R0, =__bss_start
+	EOR R1, R1, R1
+	LDR R2, =__bss_end
+	SUB R2, R2, R0
+	BL memset
+	B _irq_setup
+
+_reset_handler:
+	LDR R0, =EXCP_TYPE_ADDR
+	LDR R1, =0x545352   /* RST */
+	STR R1, [R0]        /* RST in EXCP_TYPE_ADDR */
+	B excp_reset
+
+_undefined_handler:
+	LDR R0, =EXCP_TYPE_ADDR
+	LDR R1, =0x464455   /* UDF */
+	STR R1, [R0]        /* UDF in EXCP_TYPE_ADDR */
+	B excp_reset
+
+_prefetch_abort_handler:
+	LDR R0, =EXCP_TYPE_ADDR
+	LDR R1, =0x54424150 /* PABT */
+	STR R1, [R0]        /* PABT in EXCP_TYPE_ADDR */
+	B excp_reset
+
+_data_abort_handler:
+	LDR R0, =EXCP_TYPE_ADDR
+	LDR R1, =0x54424144 /* DABT */
+	STR R1, [R0]        /* DABT in EXCP_TYPE_ADDR */
+	B excp_reset
+
+.globl irq_enable_cpu_irq_exceptions
+.type irq_enable_cpu_irq_exceptions, %function
+irq_enable_cpu_irq_exceptions:
+	MRS R12, CPSR
+	BIC R12, R12, #(IRQ | FIQ) /* IRQ/FIQ enabled */
+	MSR CPSR, R12
+	BX LR
+
+.globl irq_disable_cpu_irq_exceptions
+.type irq_disable_cpu_irq_exceptions, %function
+irq_disable_cpu_irq_exceptions:
+	MRS R12, CPSR
+	ORR R12, R12, #(IRQ | FIQ) /* IRQ/FIQ disabled */
+	MSR CPSR, R12
+	BX LR
+
+_irq_handler:
+	MOV R13, R0    /* Save R0 in R13_IRQ */
+	SUB R0, LR, #4 /* Put return address in R0_SYS */
+	MOV LR, R1     /* Save R1 in R14_IRQ (LR) */
+	MRS R1, SPSR   /* Put the SPSR in R1_SYS */
+
+	MSR CPSR_c, #(MODE_SYS | IRQ)  /* SYSTEM mode, IRQ disabled */
+	STMFD SP!, {R0, R1}            /* SPSR and PC */
+	STMFD SP!, {R2-R3, R12, LR}    /* AAPCS-clobbered registers */
+	MOV R0, SP                     /* Make SP_SYS visible to IRQ mode */
+	SUB SP, SP, #8                 /* Make room for stacking R0 and R1 */
+
+	MSR CPSR_c, #(MODE_IRQ | IRQ) /* IRQ mode, IRQ disabled */
+	STMFD R0!, {R13, R14}         /* Finish saving the context (R0, R1) */
+
+	MSR CPSR_c, #(MODE_SYS | IRQ) /* SYSTEM mode, IRQ disabled */
+	LDR R12, =irq_handler
+	MOV LR, PC                    /* Copy the return address to link register */
+	BX R12                        /* Call the C IRQ handler (ARM/THUMB) */
+
+	MSR CPSR_c, #(MODE_SYS | IRQ | FIQ) /* SYSTEM mode, IRQ/FIQ disabled */
+	MOV R0, SP                          /* Make SP_SYS visible to IRQ mode */
+	ADD SP, SP, #32                     /* Fake unstacking 8 registers from SP_SYS */
+
+	MSR CPSR_c, #(MODE_IRQ | IRQ | FIQ) /* IRQ mode, IRQ/FIQ disabled */
+	MOV SP, R0                          /* Copy SP_SYS to SP_IRQ */
+	LDR R0, [SP, #28]                   /* Load the saved SPSR from the stack */
+	MSR SPSR_cxsf, R0                   /* Copy it into SPSR_IRQ */
+
+	LDMFD SP, {R0-R3, R12, LR}^ /* Unstack all saved USER/SYSTEM registers */
+	NOP                         /* Cant access barked registers immediately */
+	LDR LR, [SP, #24]           /* Load return address from the SYS stack */
+	MOVS PC, LR                 /* Return restoring CPSR from SPSR */
+
+_fiq_handler:
+	BL fiq_handler
+
+setup_vectors:
+	/* Setup vectors */
+	LDR R0, =EXCP_VEC_BASE
+
+	LDR R1, =_reset_handler
+	STR R1, [R0, #EVP_COP_RESET_VECTOR]
+
+	LDR R1, =_undefined_handler
+	STR R1, [R0, #EVP_COP_UNDEF_VECTOR]
+
+	LDR R1, =_reset_handler
+	STR R1, [R0, #EVP_COP_SWI_VECTOR]
+
+	LDR R1, =_prefetch_abort_handler
+	STR R1, [R0, #EVP_COP_PREFETCH_ABORT_VECTOR]
+
+	LDR R1, =_data_abort_handler
+	STR R1, [R0, #EVP_COP_DATA_ABORT_VECTOR]
+
+	LDR R1, =_reset_handler
+	STR R1, [R0, #EVP_COP_RSVD_VECTOR]
+
+	LDR R1, =_irq_handler
+	STR R1, [R0, #EVP_COP_IRQ_VECTOR]
+
+	LDR R1, =_fiq_handler
+	STR R1, [R0, #EVP_COP_FIQ_VECTOR]
+
+	BX LR

bdk/fatfs_cfg.h

@@ -1,5 +1,5 @@
 /*
- * Copyright (c) 2018 naehrwert
+ * Copyright (c) 2020 CTCaer
  *
  * This program is free software; you can redistribute it and/or modify it
  * under the terms and conditions of the GNU General Public License,
@@ -14,14 +14,15 @@
  * along with this program.  If not, see <http://www.gnu.org/licenses/>.
  */
 
-#ifndef _SDRAM_H_
-#define _SDRAM_H_
+#ifndef _FATFS_CFG_H_
+#define _FATFS_CFG_H_
 
-#include "sdram_param_t210.h"
-
-void sdram_init();
-sdram_params_t *sdram_get_params();
-sdram_params_t *sdram_get_params_patched();
-void sdram_lp0_save_params(const void *params);
+// define FFCFG_INC in a project to use a specific FatFS configuration.
+// Example: FFCFG_INC := '"../$(PROJECT_DIR)/libs/fatfs/ffconf.h"'
+#ifdef FFCFG_INC
+#include FFCFG_INC
+#else
+#include "fatfs_conf.h"
+#endif
 
 #endif

bdk/fatfs_conf.h

@@ -0,0 +1,305 @@
+/*---------------------------------------------------------------------------/
+/  FatFs Functional Configurations
+/---------------------------------------------------------------------------*/
+
+#define FFCONF_DEF	86604	/* Revision ID */
+
+/*---------------------------------------------------------------------------/
+/ Function Configurations
+/---------------------------------------------------------------------------*/
+
+#define FF_FS_READONLY	0
+/* This option switches read-only configuration. (0:Read/Write or 1:Read-only)
+/  Read-only configuration removes writing API functions, f_write(), f_sync(),
+/  f_unlink(), f_mkdir(), f_chmod(), f_rename(), f_truncate(), f_getfree()
+/  and optional writing functions as well. */
+
+
+#define FF_FS_MINIMIZE	0
+/* This option defines minimization level to remove some basic API functions.
+/
+/   0: Basic functions are fully enabled.
+/   1: f_stat(), f_getfree(), f_unlink(), f_mkdir(), f_truncate() and f_rename()
+/      are removed.
+/   2: f_opendir(), f_readdir() and f_closedir() are removed in addition to 1.
+/   3: f_lseek() function is removed in addition to 2. */
+
+
+#define FF_USE_STRFUNC	2
+/* This option switches string functions, f_gets(), f_putc(), f_puts() and f_printf().
+/
+/  0: Disable string functions.
+/  1: Enable without LF-CRLF conversion.
+/  2: Enable with LF-CRLF conversion. */
+
+
+#define FF_USE_FIND		1
+/* This option switches filtered directory read functions, f_findfirst() and
+/  f_findnext(). (0:Disable, 1:Enable 2:Enable with matching altname[] too) */
+
+
+#define FF_USE_MKFS		0
+/* This option switches f_mkfs() function. (0:Disable or 1:Enable) */
+
+#if FF_USE_MKFS
+#define FF_MKFS_LABEL "SWITCH SD  "
+#endif
+/* This sets FAT/FAT32 label. Exactly 11 characters, all caps. */
+
+
+#define FF_USE_FASTSEEK	0
+/* This option switches fast seek function. (0:Disable or 1:Enable) */
+
+#define FF_FASTFS 0
+#if FF_FASTFS
+#undef FF_USE_FASTSEEK
+#define FF_USE_FASTSEEK	1
+#endif
+/* This option switches fast access to chained clusters. (0:Disable or 1:Enable) */
+
+
+#define FF_SIMPLE_GPT 1
+/* This option switches support for the first GPT partition. (0:Disable or 1:Enable) */
+
+
+#define FF_USE_EXPAND	0
+/* This option switches f_expand function. (0:Disable or 1:Enable) */
+
+
+#define FF_USE_CHMOD	1
+/* This option switches attribute manipulation functions, f_chmod() and f_utime().
+/  (0:Disable or 1:Enable) Also FF_FS_READONLY needs to be 0 to enable this option. */
+
+
+#define FF_USE_LABEL	0
+/* This option switches volume label functions, f_getlabel() and f_setlabel().
+/  (0:Disable or 1:Enable) */
+
+
+#define FF_USE_FORWARD	0
+/* This option switches f_forward() function. (0:Disable or 1:Enable) */
+
+
+/*---------------------------------------------------------------------------/
+/ Locale and Namespace Configurations
+/---------------------------------------------------------------------------*/
+
+#define FF_CODE_PAGE	850
+/* This option specifies the OEM code page to be used on the target system.
+/  Incorrect code page setting can cause a file open failure.
+/
+/   437 - U.S.
+/   720 - Arabic
+/   737 - Greek
+/   771 - KBL
+/   775 - Baltic
+/   850 - Latin 1
+/   852 - Latin 2
+/   855 - Cyrillic
+/   857 - Turkish
+/   860 - Portuguese
+/   861 - Icelandic
+/   862 - Hebrew
+/   863 - Canadian French
+/   864 - Arabic
+/   865 - Nordic
+/   866 - Russian
+/   869 - Greek 2
+/   932 - Japanese (DBCS)
+/   936 - Simplified Chinese (DBCS)
+/   949 - Korean (DBCS)
+/   950 - Traditional Chinese (DBCS)
+/     0 - Include all code pages above and configured by f_setcp()
+*/
+
+
+#define FF_USE_LFN		3
+#define FF_MAX_LFN		255
+/* The FF_USE_LFN switches the support for LFN (long file name).
+/
+/   0: Disable LFN. FF_MAX_LFN has no effect.
+/   1: Enable LFN with static working buffer on the BSS. Always NOT thread-safe.
+/   2: Enable LFN with dynamic working buffer on the STACK.
+/   3: Enable LFN with dynamic working buffer on the HEAP.
+/
+/  To enable the LFN, ffunicode.c needs to be added to the project. The LFN function
+/  requiers certain internal working buffer occupies (FF_MAX_LFN + 1) * 2 bytes and
+/  additional (FF_MAX_LFN + 44) / 15 * 32 bytes when exFAT is enabled.
+/  The FF_MAX_LFN defines size of the working buffer in UTF-16 code unit and it can
+/  be in range of 12 to 255. It is recommended to be set 255 to fully support LFN
+/  specification.
+/  When use stack for the working buffer, take care on stack overflow. When use heap
+/  memory for the working buffer, memory management functions, ff_memalloc() and
+/  ff_memfree() in ffsystem.c, need to be added to the project. */
+
+
+#define FF_LFN_UNICODE	0
+/* This option switches the character encoding on the API when LFN is enabled.
+/
+/   0: ANSI/OEM in current CP (TCHAR = char)
+/   1: Unicode in UTF-16 (TCHAR = WCHAR)
+/   2: Unicode in UTF-8 (TCHAR = char)
+/   3: Unicode in UTF-32 (TCHAR = DWORD)
+/
+/  Also behavior of string I/O functions will be affected by this option.
+/  When LFN is not enabled, this option has no effect. */
+
+
+#define FF_LFN_BUF		255
+#define FF_SFN_BUF		12
+/* This set of options defines size of file name members in the FILINFO structure
+/  which is used to read out directory items. These values should be suffcient for
+/  the file names to read. The maximum possible length of the read file name depends
+/  on character encoding. When LFN is not enabled, these options have no effect. */
+
+
+#define FF_STRF_ENCODE	0
+/* When FF_LFN_UNICODE >= 1 with LFN enabled, string I/O functions, f_gets(),
+/  f_putc(), f_puts and f_printf() convert the character encoding in it.
+/  This option selects assumption of character encoding ON THE FILE to be
+/  read/written via those functions.
+/
+/   0: ANSI/OEM in current CP
+/   1: Unicode in UTF-16LE
+/   2: Unicode in UTF-16BE
+/   3: Unicode in UTF-8
+*/
+
+
+#define FF_FS_RPATH		0
+/* This option configures support for relative path.
+/
+/   0: Disable relative path and remove related functions.
+/   1: Enable relative path. f_chdir() and f_chdrive() are available.
+/   2: f_getcwd() function is available in addition to 1.
+*/
+
+
+/*---------------------------------------------------------------------------/
+/ Drive/Volume Configurations
+/---------------------------------------------------------------------------*/
+
+#define FF_VOLUMES		1
+/* Number of volumes (logical drives) to be used. (1-10) */
+
+
+#define FF_STR_VOLUME_ID	0
+#define FF_VOLUME_STRS		"sd"
+/* FF_STR_VOLUME_ID switches support for volume ID in arbitrary strings.
+/  When FF_STR_VOLUME_ID is set to 1 or 2, arbitrary strings can be used as drive
+/  number in the path name. FF_VOLUME_STRS defines the volume ID strings for each
+/  logical drives. Number of items must not be less than FF_VOLUMES. Valid
+/  characters for the volume ID strings are A-Z, a-z and 0-9, however, they are
+/  compared in case-insensitive. If FF_STR_VOLUME_ID >= 1 and FF_VOLUME_STRS is
+/  not defined, a user defined volume string table needs to be defined as:
+/
+/  const char* VolumeStr[FF_VOLUMES] = {"ram","flash","sd","usb",...
+/  Order is important. Any change to order, must also be reflected to diskio drive enum.
+*/
+
+
+#define FF_MULTI_PARTITION	0
+/* This option switches support for multiple volumes on the physical drive.
+/  By default (0), each logical drive number is bound to the same physical drive
+/  number and only an FAT volume found on the physical drive will be mounted.
+/  When this function is enabled (1), each logical drive number can be bound to
+/  arbitrary physical drive and partition listed in the VolToPart[]. Also f_fdisk()
+/  funciton will be available. */
+
+
+#define FF_MIN_SS		512
+#define FF_MAX_SS		512
+/* This set of options configures the range of sector size to be supported. (512,
+/  1024, 2048 or 4096) Always set both 512 for most systems, generic memory card and
+/  harddisk. But a larger value may be required for on-board flash memory and some
+/  type of optical media. When FF_MAX_SS is larger than FF_MIN_SS, FatFs is configured
+/  for variable sector size mode and disk_ioctl() function needs to implement
+/  GET_SECTOR_SIZE command. */
+
+
+#define FF_USE_TRIM		0
+/* This option switches support for ATA-TRIM. (0:Disable or 1:Enable)
+/  To enable Trim function, also CTRL_TRIM command should be implemented to the
+/  disk_ioctl() function. */
+
+
+#define FF_FS_NOFSINFO	1
+/* If you need to know correct free space on the FAT32 volume, set bit 0 of this
+/  option, and f_getfree() function at first time after volume mount will force
+/  a full FAT scan. Bit 1 controls the use of last allocated cluster number.
+/
+/  bit0=0: Use free cluster count in the FSINFO if available.
+/  bit0=1: Do not trust free cluster count in the FSINFO.
+/  bit1=0: Use last allocated cluster number in the FSINFO if available.
+/  bit1=1: Do not trust last allocated cluster number in the FSINFO.
+*/
+
+
+
+/*---------------------------------------------------------------------------/
+/ System Configurations
+/---------------------------------------------------------------------------*/
+
+#define FF_FS_TINY		0
+/* This option switches tiny buffer configuration. (0:Normal or 1:Tiny)
+/  At the tiny configuration, size of file object (FIL) is shrinked FF_MAX_SS bytes.
+/  Instead of private sector buffer eliminated from the file object, common sector
+/  buffer in the filesystem object (FATFS) is used for the file data transfer. */
+
+
+#define FF_FS_EXFAT		1
+/* This option switches support for exFAT filesystem. (0:Disable or 1:Enable)
+/  To enable exFAT, also LFN needs to be enabled. (FF_USE_LFN >= 1)
+/  Note that enabling exFAT discards ANSI C (C89) compatibility. */
+
+
+#define FF_FS_NORTC		1
+#define FF_NORTC_MON	1
+#define FF_NORTC_MDAY	1
+#define FF_NORTC_YEAR	2022
+/* The option FF_FS_NORTC switches timestamp function. If the system does not have
+/  any RTC function or valid timestamp is not needed, set FF_FS_NORTC = 1 to disable
+/  the timestamp function. Every object modified by FatFs will have a fixed timestamp
+/  defined by FF_NORTC_MON, FF_NORTC_MDAY and FF_NORTC_YEAR in local time.
+/  To enable timestamp function (FF_FS_NORTC = 0), get_fattime() function need to be
+/  added to the project to read current time form real-time clock. FF_NORTC_MON,
+/  FF_NORTC_MDAY and FF_NORTC_YEAR have no effect.
+/  These options have no effect at read-only configuration (FF_FS_READONLY = 1). */
+
+
+#define FF_FS_LOCK		0
+/* The option FF_FS_LOCK switches file lock function to control duplicated file open
+/  and illegal operation to open objects. This option must be 0 when FF_FS_READONLY
+/  is 1.
+/
+/  0:  Disable file lock function. To avoid volume corruption, application program
+/      should avoid illegal open, remove and rename to the open objects.
+/  >0: Enable file lock function. The value defines how many files/sub-directories
+/      can be opened simultaneously under file lock control. Note that the file
+/      lock control is independent of re-entrancy. */
+
+
+/* #include <somertos.h>	// O/S definitions */
+#define FF_FS_REENTRANT	0
+#define FF_FS_TIMEOUT	1000
+#define FF_SYNC_t		HANDLE
+/* The option FF_FS_REENTRANT switches the re-entrancy (thread safe) of the FatFs
+/  module itself. Note that regardless of this option, file access to different
+/  volume is always re-entrant and volume control functions, f_mount(), f_mkfs()
+/  and f_fdisk() function, are always not re-entrant. Only file/directory access
+/  to the same volume is under control of this function.
+/
+/   0: Disable re-entrancy. FF_FS_TIMEOUT and FF_SYNC_t have no effect.
+/   1: Enable re-entrancy. Also user provided synchronization handlers,
+/      ff_req_grant(), ff_rel_grant(), ff_del_syncobj() and ff_cre_syncobj()
+/      function, must be added to the project. Samples are available in
+/      option/syscall.c.
+/
+/  The FF_FS_TIMEOUT defines timeout period in unit of time tick.
+/  The FF_SYNC_t defines O/S dependent sync object type. e.g. HANDLE, ID, OS_EVENT*,
+/  SemaphoreHandle_t and etc. A header file for O/S definitions needs to be
+/  included somewhere in the scope of ff.h. */
+
+
+
+/*--- End of configuration options ---*/

bdk/gfx_utils.h

@@ -1,5 +1,5 @@
 /*
- * Copyright (c) 2018 naehrwert
+ * Copyright (c) 2020 CTCaer
  *
  * This program is free software; you can redistribute it and/or modify it
  * under the terms and conditions of the GNU General Public License,
@@ -14,11 +14,11 @@
  * along with this program.  If not, see <http://www.gnu.org/licenses/>.
  */
 
-#ifndef _CLUSTER_H_
-#define _CLUSTER_H_
+#ifndef _GFX_UTILS_H_
+#define _GFX_UTILS_H_
 
-#include "../utils/types.h"
-
-void cluster_boot_cpu0(u32 entry);
+#ifdef GFX_INC
+#include GFX_INC
+#endif
 
 #endif

bdk/ianos/elfload/elf.h

@@ -29,33 +29,34 @@
 
 #ifndef ELF_H
 #define ELF_H
-#include <stdint.h>
 
-typedef uint8_t Elf_Byte;
+#include <utils/types.h>
 
-typedef uint32_t Elf32_Addr; /* Unsigned program address */
-typedef uint32_t Elf32_Off;  /* Unsigned file offset */
-typedef int32_t Elf32_Sword; /* Signed large integer */
-typedef uint32_t Elf32_Word; /* Unsigned large integer */
-typedef uint16_t Elf32_Half; /* Unsigned medium integer */
+typedef u8 Elf_Byte;
 
-typedef uint64_t Elf64_Addr;
-typedef uint64_t Elf64_Off;
-typedef int32_t Elf64_Shalf;
+typedef u32 Elf32_Addr; /* Unsigned program address */
+typedef u32 Elf32_Off;  /* Unsigned file offset */
+typedef s32 Elf32_Sword; /* Signed large integer */
+typedef u32 Elf32_Word; /* Unsigned large integer */
+typedef u16 Elf32_Half; /* Unsigned medium integer */
+
+typedef u64 Elf64_Addr;
+typedef u64 Elf64_Off;
+typedef s32 Elf64_Shalf;
 
 #ifdef __alpha__
-typedef int64_t Elf64_Sword;
-typedef uint64_t Elf64_Word;
+typedef s64 Elf64_Sword;
+typedef u64 Elf64_Word;
 #else
-typedef int32_t Elf64_Sword;
-typedef uint32_t Elf64_Word;
+typedef s32 Elf64_Sword;
+typedef u32 Elf64_Word;
 #endif
 
-typedef int64_t Elf64_Sxword;
-typedef uint64_t Elf64_Xword;
+typedef s64 Elf64_Sxword;
+typedef u64 Elf64_Xword;
 
-typedef uint32_t Elf64_Half;
-typedef uint16_t Elf64_Quarter;
+typedef u32 Elf64_Half;
+typedef u16 Elf64_Quarter;
 
 /*
  * e_ident[] identification indexes
@@ -376,7 +377,7 @@ typedef struct
 
 #define ELF64_R_SYM(info) ((info) >> 32)
 #define ELF64_R_TYPE(info) ((info)&0xFFFFFFFF)
-#define ELF64_R_INFO(s, t) (((s) << 32) + (__uint32_t)(t))
+#define ELF64_R_INFO(s, t) (((s) << 32) + (u32)(t))
 
 #if defined(__mips64__) && defined(__MIPSEL__)
 /*
@@ -389,7 +390,7 @@ typedef struct
 #undef ELF64_R_INFO
 #define ELF64_R_TYPE(info) (swap32((info) >> 32))
 #define ELF64_R_SYM(info) ((info)&0xFFFFFFFF)
-#define ELF64_R_INFO(s, t) (((__uint64_t)swap32(t) << 32) + (__uint32_t)(s))
+#define ELF64_R_INFO(s, t) (((u64)swap32(t) << 32) + (u32)(s))
 #endif /* __mips64__ && __MIPSEL__ */
 
 /* Program Header */
@@ -444,7 +445,7 @@ typedef struct
 /* Dynamic structure */
 typedef struct
 {
-    Elf32_Sword d_tag; /* controls meaning of d_val */
+    Elf32_Word d_tag; /* controls meaning of d_val */
     union {
         Elf32_Word d_val; /* Multiple meanings - see d_tag */
         Elf32_Addr d_ptr; /* program virtual address */

bdk/ianos/elfload/elfload.c

@@ -25,7 +25,7 @@ el_status el_pread(el_ctx *ctx, void *def, size_t nb, size_t offset)
 }
 
 #define EL_PHOFF(ctx, num) (((ctx)->ehdr.e_phoff + (num) *(ctx)->ehdr.e_phentsize))
-el_status el_findphdr(el_ctx *ctx, Elf_Phdr *phdr, uint32_t type, unsigned *i)
+el_status el_findphdr(el_ctx *ctx, Elf_Phdr *phdr, u32 type, unsigned *i)
 {
 	el_status rv = EL_OK;
 	for (; *i < ctx->ehdr.e_phnum; (*i)++)
@@ -44,7 +44,7 @@ el_status el_findphdr(el_ctx *ctx, Elf_Phdr *phdr, uint32_t type, unsigned *i)
 }
 
 #define EL_SHOFF(ctx, num) (((ctx)->ehdr.e_shoff + (num) *(ctx)->ehdr.e_shentsize))
-el_status el_findshdr(el_ctx *ctx, Elf_Shdr *shdr, uint32_t type, unsigned *i)
+el_status el_findshdr(el_ctx *ctx, Elf_Shdr *shdr, u32 type, unsigned *i)
 {
 	el_status rv = EL_OK;
 
@@ -213,7 +213,7 @@ el_status el_load(el_ctx *ctx, el_alloc_cb alloc)
 	return rv;
 }
 
-el_status el_finddyn(el_ctx *ctx, Elf_Dyn *dyn, uint32_t tag)
+el_status el_finddyn(el_ctx *ctx, Elf_Dyn *dyn, u32 tag)
 {
 	el_status rv = EL_OK;
 	size_t ndyn = ctx->dynsize / sizeof(Elf_Dyn);
@@ -231,7 +231,7 @@ el_status el_finddyn(el_ctx *ctx, Elf_Dyn *dyn, uint32_t tag)
 	return EL_OK;
 }
 
-el_status el_findrelocs(el_ctx *ctx, el_relocinfo *ri, uint32_t type)
+el_status el_findrelocs(el_ctx *ctx, el_relocinfo *ri, u32 type)
 {
 	el_status rv = EL_OK;
 

bdk/ianos/elfload/elfload.h

@@ -22,10 +22,8 @@
 #include "elfarch.h"
 #include "elf.h"
 
-#include "../../utils/types.h"
-
 #ifdef DEBUG
-#include "../../gfx/gfx.h"
+#include <gfx_utils.h>
 #define EL_DEBUG(format, ...) \
 	gfx_printf(format __VA_OPT__(, ) __VA_ARGS__)
 #else
@@ -100,7 +98,7 @@ el_status el_load(el_ctx *ctx, el_alloc_cb alloccb);
  * If the end of the phdrs table was reached, *i is set to -1 and the contents
  * of *phdr are undefined
  */
-el_status el_findphdr(el_ctx *ctx, Elf_Phdr *phdr, uint32_t type, unsigned *i);
+el_status el_findphdr(el_ctx *ctx, Elf_Phdr *phdr, u32 type, unsigned *i);
 
 /* Relocate the loaded executable */
 el_status el_relocate(el_ctx *ctx);
@@ -108,7 +106,7 @@ el_status el_relocate(el_ctx *ctx);
 /* find a dynamic table entry
  * returns the entry on success, dyn->d_tag = DT_NULL on failure
  */
-el_status el_finddyn(el_ctx *ctx, Elf_Dyn *dyn, uint32_t type);
+el_status el_finddyn(el_ctx *ctx, Elf_Dyn *dyn, u32 type);
 
 typedef struct
 {
@@ -122,6 +120,6 @@ typedef struct
  * pass DT_REL or DT_RELA for type
  * sets ri->entrysize = 0 if not found
  */
-el_status el_findrelocs(el_ctx *ctx, el_relocinfo *ri, uint32_t type);
+el_status el_findrelocs(el_ctx *ctx, el_relocinfo *ri, u32 type);
 
 #endif

bdk/ianos/elfload/elfreloc_aarch64.c

@@ -23,9 +23,9 @@
 
 el_status el_applyrela(el_ctx *ctx, Elf_RelA *rel)
 {
-	uintptr_t *p = (uintptr_t *)(rel->r_offset + ctx->base_load_paddr);
-	uint32_t type = ELF_R_TYPE(rel->r_info);
-	uint32_t sym = ELF_R_SYM(rel->r_info);
+	uptr *p = (uptr *)(rel->r_offset + ctx->base_load_paddr);
+	u32 type = ELF_R_TYPE(rel->r_info);
+	u32 sym = ELF_R_SYM(rel->r_info);
 
 	switch (type)
 	{
@@ -53,9 +53,9 @@ el_status el_applyrela(el_ctx *ctx, Elf_RelA *rel)
 
 el_status el_applyrel(el_ctx *ctx, Elf_Rel *rel)
 {
-	uintptr_t *p = (uintptr_t *)(rel->r_offset + ctx->base_load_paddr);
-	uint32_t type = ELF_R_TYPE(rel->r_info);
-	uint32_t sym = ELF_R_SYM(rel->r_info);
+	uptr *p = (uptr *)(rel->r_offset + ctx->base_load_paddr);
+	u32 type = ELF_R_TYPE(rel->r_info);
+	u32 sym = ELF_R_SYM(rel->r_info);
 
 	switch (type)
 	{

bdk/ianos/elfload/elfreloc_arm.c

@@ -20,9 +20,9 @@
 
 el_status el_applyrel(el_ctx *ctx, Elf_Rel *rel)
 {
-	uint32_t sym = ELF_R_SYM(rel->r_info);                              // Symbol offset
-	uint32_t type = ELF_R_TYPE(rel->r_info);                            // Relocation Type
-	uintptr_t *p = (uintptr_t *)(rel->r_offset + ctx->base_load_paddr); // Target Addr
+	u32 sym = ELF_R_SYM(rel->r_info);                              // Symbol offset
+	u32 type = ELF_R_TYPE(rel->r_info);                            // Relocation Type
+	uptr *p = (uptr *)(rel->r_offset + ctx->base_load_paddr); // Target Addr
 
 #if 0 // For later symbol usage
 	Elf32_Sym *elfSym;

bdk/ianos/ianos.c

@@ -18,33 +18,36 @@
 #include <string.h>
 
 #include "ianos.h"
-#include "../utils/types.h"
-#include "../libs/elfload/elfload.h"
-#include "../../common/common_module.h"
-#include "../mem/heap.h"
-#include "../gfx/gfx.h"
+#include "elfload/elfload.h"
+#include <module.h>
+#include <mem/heap.h>
+#include <power/max7762x.h>
+#include <storage/sd.h>
+#include <utils/types.h>
+
+#include <gfx_utils.h>
 
 #define IRAM_LIB_ADDR 0x4002B000
 #define DRAM_LIB_ADDR 0xE0000000
 
 extern heap_t _heap;
 
-extern void *sd_file_read(const char *path, u32 *fsize);
-extern bool sd_mount();
-extern void sd_unmount();
-
 void *elfBuf = NULL;
 void *fileBuf = NULL;
 
 static void _ianos_call_ep(moduleEntrypoint_t entrypoint, void *moduleConfig)
 {
 	bdkParams_t bdkParameters = (bdkParams_t)malloc(sizeof(struct _bdkParams_t));
-	bdkParameters->gfxCon = &gfx_con;
-	bdkParameters->gfxCtx = &gfx_ctxt;
+	bdkParameters->gfxCon = (void *)&gfx_con;
+	bdkParameters->gfxCtx = (void *)&gfx_ctxt;
 	bdkParameters->memcpy = (memcpy_t)&memcpy;
 	bdkParameters->memset = (memset_t)&memset;
 	bdkParameters->sharedHeap = &_heap;
 
+	// Extra functions.
+	bdkParameters->extension_magic = IANOS_EXT0;
+	bdkParameters->reg_voltage_set = (reg_voltage_set_t)&max7762x_regulator_set_voltage;
+
 	entrypoint(moduleConfig, bdkParameters);
 }
 
@@ -66,30 +69,21 @@ static bool _ianos_read_cb(el_ctx *ctx, void *dest, size_t numberBytes, size_t o
 }
 
 //TODO: Support shared libraries.
-uintptr_t ianos_loader(bool sdmount, char *path, elfType_t type, void *moduleConfig)
+uintptr_t ianos_loader(char *path, elfType_t type, void *moduleConfig)
 {
+	el_ctx ctx;
 	uintptr_t epaddr = 0;
 
-	if (sdmount)
-	{
-		if (!sd_mount())
-			goto elfLoadFinalOut;
-	}
-
+	// Read library.
 	fileBuf = sd_file_read(path, NULL);
 
-	if (sdmount)
-		sd_unmount();
-
 	if (!fileBuf)
-		goto elfLoadFinalOut;
+		goto out;
 
-
-	el_ctx ctx;
 	ctx.pread = _ianos_read_cb;
 
 	if (el_init(&ctx))
-		goto elfLoadFinalOut;
+		goto out;
 
 	// Set our relocated library's buffer.
 	switch (type & 0xFFFF)
@@ -97,22 +91,21 @@ uintptr_t ianos_loader(bool sdmount, char *path, elfType_t type, void *moduleCon
 	case EXEC_ELF:
 	case AR64_ELF:
 		elfBuf = (void *)DRAM_LIB_ADDR;
-		sd_unmount();
 		break;
 	default:
 		elfBuf = malloc(ctx.memsz); // Aligned to 0x10 by default.
 	}
 
 	if (!elfBuf)
-		goto elfLoadFinalOut;
+		goto out;
 
 	// Load and relocate library.
 	ctx.base_load_vaddr = ctx.base_load_paddr = (uintptr_t)elfBuf;
 	if (el_load(&ctx, _ianos_alloc_cb))
-		goto elfFreeOut;
+		goto out_free;
 
 	if (el_relocate(&ctx))
-		goto elfFreeOut;
+		goto out_free;
 
 	// Launch.
 	epaddr = ctx.ehdr.e_entry + (uintptr_t)elfBuf;
@@ -120,12 +113,11 @@ uintptr_t ianos_loader(bool sdmount, char *path, elfType_t type, void *moduleCon
 
 	_ianos_call_ep(ep, moduleConfig);
 
-elfFreeOut:
+out_free:
 	free(fileBuf);
 	elfBuf = NULL;
 	fileBuf = NULL;
 
-elfLoadFinalOut:
-
+out:
 	return epaddr;
 }

bdk/ianos/ianos.h

@@ -18,7 +18,7 @@
 #ifndef IANOS_H
 #define IANOS_H
 
-#include "../utils/types.h"
+#include <utils/types.h>
 
 typedef enum
 {
@@ -29,6 +29,6 @@ typedef enum
 	KEEP_IN_RAM = (1 << 31)  // Shared library mask.
 } elfType_t;
 
-uintptr_t ianos_loader(bool sdmount, char *path, elfType_t type, void* config);
+uintptr_t ianos_loader(char *path, elfType_t type, void* config);
 
 #endif

bdk/input/als.c

@@ -0,0 +1,156 @@
+/*
+ * Ambient light sensor driver for Nintendo Switch's Rohm BH1730
+ *
+ * Copyright (c) 2018 CTCaer
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include "als.h"
+#include <power/max7762x.h>
+#include <soc/clock.h>
+#include <soc/i2c.h>
+#include <soc/pinmux.h>
+#include <utils/util.h>
+
+#define BH1730_DEFAULT_GAIN        BH1730_GAIN_64X
+#define BH1730_DEFAULT_ICYCLE       38
+
+#define BH1730_INTERNAL_CLOCK_NS   2800
+#define BH1730_ADC_CALC_DELAY_US   2000 /* BH1730_INTERNAL_CLOCK_MS * 714 */
+#define BH1730_ITIME_CYCLE_TO_US   2700 /* BH1730_INTERNAL_CLOCK_MS * 964 */
+
+#define BH1730_DEFAULT_ITIME_MS	   100
+
+#define BH1730_LUX_MULTIPLIER      3600
+#define BH1730_LUX_MULTIPLIER_AULA 1410
+
+#define BH1730_LUX_MAX            100000
+
+typedef struct _opt_win_cal_t
+{
+	u32 rc;
+	u32 cv;
+	u32 ci;
+} opt_win_cal_t;
+
+// Nintendo Switch Icosa/Iowa Optical Window calibration.
+static const opt_win_cal_t opt_win_cal_default[] = {
+	{  500, 5002, 7502 },
+	{  754, 2250, 2000 },
+	{ 1029, 1999, 1667 },
+	{ 1373,  884,  583 },
+	{ 1879,  309,  165 }
+};
+
+// Nintendo Switch Aula Optical Window calibration.
+static const opt_win_cal_t opt_win_cal_aula[] = {
+	{  231, 9697, 30300 },
+	{  993, 3333,  2778 },
+	{ 1478, 1621,  1053 },
+	{ 7500,   81,    10 }
+};
+
+static const u32 als_gain_idx_tbl[4] = { 1, 2, 64, 128 };
+
+void set_als_cfg(als_ctxt_t *als_ctxt, u8 gain, u8 cycle)
+{
+	if (gain > BH1730_GAIN_128X)
+		gain = BH1730_GAIN_128X;
+
+	if (!cycle)
+		cycle = 1;
+	else if (cycle > 255)
+		cycle = 255;
+
+	i2c_send_byte(I2C_2, BH1730_I2C_ADDR, BH1730_ADDR(BH1730_GAIN_REG),   gain);
+	i2c_send_byte(I2C_2, BH1730_I2C_ADDR, BH1730_ADDR(BH1730_TIMING_REG), (256 - cycle));
+
+	als_ctxt->gain = gain;
+	als_ctxt->cycle = cycle;
+}
+
+void get_als_lux(als_ctxt_t *als_ctxt)
+{
+	u32 data[2];
+	u32 vi_light;
+	u32 ir_light;
+	u64 lux = 0;
+	u32 itime_us = BH1730_ITIME_CYCLE_TO_US * als_ctxt->cycle;
+
+	// Get visible and ir light raw data. Mode is continuous so waiting for new values doesn't matter.
+	data[0] = i2c_recv_byte(I2C_2, BH1730_I2C_ADDR, BH1730_ADDR(BH1730_DATA0LOW_REG)) +
+		     (i2c_recv_byte(I2C_2, BH1730_I2C_ADDR, BH1730_ADDR(BH1730_DATA0HIGH_REG)) << 8);
+	data[1] = i2c_recv_byte(I2C_2, BH1730_I2C_ADDR, BH1730_ADDR(BH1730_DATA1LOW_REG)) +
+		     (i2c_recv_byte(I2C_2, BH1730_I2C_ADDR, BH1730_ADDR(BH1730_DATA1HIGH_REG)) << 8);
+
+	vi_light = data[0];
+	ir_light = data[1];
+
+	als_ctxt->vi_light = vi_light;
+	als_ctxt->ir_light = ir_light;
+	als_ctxt->over_limit = vi_light > 65534 || ir_light > 65534;
+
+	if (!vi_light)
+	{
+		als_ctxt->lux = 0;
+
+		return;
+	}
+
+	// Set calibration parameters.
+	u32 lux_multiplier = BH1730_LUX_MULTIPLIER;
+	u32 opt_win_cal_count = ARRAY_SIZE(opt_win_cal_default);
+	const opt_win_cal_t *opt_win_cal = opt_win_cal_default;
+
+	// Apply optical window calibration coefficients.
+	for (u32 i = 0; i < opt_win_cal_count; i++)
+	{
+		if (1000 * ir_light / vi_light < opt_win_cal[i].rc)
+		{
+			lux = ((u64)opt_win_cal[i].cv * data[0]) - (opt_win_cal[i].ci * data[1]);
+			break;
+		}
+	}
+
+	lux *= BH1730_DEFAULT_ITIME_MS * lux_multiplier;
+	lux /= als_gain_idx_tbl[als_ctxt->gain] * itime_us;
+	lux /= 1000;
+
+	if (lux > BH1730_LUX_MAX)
+		lux = BH1730_LUX_MAX;
+
+	als_ctxt->lux = lux;
+}
+
+u8 als_power_on(als_ctxt_t *als_ctxt)
+{
+	// Enable power to ALS IC.
+	max7762x_regulator_set_voltage(REGULATOR_LDO6, 2900000);
+	max7762x_regulator_enable(REGULATOR_LDO6, true);
+
+	// Init I2C2.
+	pinmux_config_i2c(I2C_2);
+	clock_enable_i2c(I2C_2);
+	i2c_init(I2C_2);
+
+	// Initialize ALS.
+	u8 id = i2c_recv_byte(I2C_2, BH1730_I2C_ADDR, BH1730_ADDR(0x12));
+	i2c_send_byte(I2C_2, BH1730_I2C_ADDR, BH1730_SPEC(BH1730_SPECCMD_RESET), 0);
+
+	set_als_cfg(als_ctxt, BH1730_DEFAULT_GAIN, BH1730_DEFAULT_ICYCLE);
+
+	i2c_send_byte(I2C_2, BH1730_I2C_ADDR, BH1730_ADDR(BH1730_CONTROL_REG), BH1730_CTL_POWER_ON | BH1730_CTL_ADC_EN);
+
+	return id;
+}

bdk/input/als.h

@@ -19,7 +19,7 @@
 #ifndef __ALS_H_
 #define __ALS_H_
 
-#include "../utils/types.h"
+#include <utils/types.h>
 
 #define BH1730_I2C_ADDR 0x29
 
@@ -45,21 +45,21 @@
 #define BH1730_DATA1LOW_REG  0x16
 #define BH1730_DATA1HIGH_REG 0x17
 
-#define BH1730_ADDR(reg) (BH1730_CMD_MAGIC | BH1730_CMD_SETADDR | reg)
-#define BH1730_SPEC(cmd) (BH1730_CMD_MAGIC | BH1730_CMD_SPECCMD | cmd)
+#define BH1730_ADDR(reg) (BH1730_CMD_MAGIC | BH1730_CMD_SETADDR | (reg))
+#define BH1730_SPEC(cmd) (BH1730_CMD_MAGIC | BH1730_CMD_SPECCMD | (cmd))
 
-typedef struct _als_table_t
+typedef struct _als_ctxt_t
 {
-	float lux;
+	u32  lux;
 	bool over_limit;
-	u32 vi_light;
-	u32 ir_light;
-	u8 gain;
-	u8 itime;
-} als_table_t;
+	u32  vi_light;
+	u32  ir_light;
+	u8   gain;
+	u8   cycle;
+} als_ctxt_t;
 
-void set_als_cfg(als_table_t *als_val, u8 gain, u8 itime);
-void get_als_lux(als_table_t *als_val);
-u8 als_init(als_table_t *als_val);
+void set_als_cfg(als_ctxt_t *als_ctxt, u8 gain, u8 cycle);
+void get_als_lux(als_ctxt_t *als_ctxt);
+u8   als_power_on(als_ctxt_t *als_ctxt);
 
 #endif /* __ALS_H_ */

bdk/input/joycon.h

@@ -0,0 +1,108 @@
+/*
+ * Ambient light sensor driver for Nintendo Switch's Rohm BH1730
+ *
+ * Copyright (c) 2018 CTCaer
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef __JOYCON_H_
+#define __JOYCON_H_
+
+#include <utils/types.h>
+
+#define JC_BTNS_DIRECTION_PAD 0xF0000
+#define JC_BTNS_PREV_NEXT     0x800080
+#define JC_BTNS_ENTER         0x400008
+#define JC_BTNS_ESC           0x4
+
+#define JC_BTNS_ALL (JC_BTNS_PREV_NEXT | JC_BTNS_ENTER | JC_BTNS_DIRECTION_PAD | JC_BTNS_ESC)
+
+typedef struct _jc_bt_conn_t
+{
+	u8 type;
+	u8 mac[6];
+	u8 host_mac[6];
+	u8 ltk[16];
+} jc_bt_conn_t;
+
+typedef struct _jc_gamepad_rpt_t
+{
+	union
+	{
+		struct
+		{
+			// Joy-Con (R).
+/*00*/		u32 y:1;
+/*01*/		u32 x:1;
+/*02*/		u32 b:1;
+/*03*/		u32 a:1;
+/*04*/		u32 sr_r:1;
+/*05*/		u32 sl_r:1;
+/*06*/		u32 r:1;
+/*07*/		u32 zr:1;
+
+			// Shared
+/*08*/		u32 minus:1;
+/*09*/		u32 plus:1;
+/*10*/		u32 r3:1;
+/*11*/		u32 l3:1;
+/*12*/		u32 home:1;
+/*13*/		u32 cap:1;
+/*14*/		u32 pad:1;
+/*15*/		u32 wired:1;
+
+			// Joy-Con (L).
+/*16*/		u32 down:1;
+/*17*/		u32 up:1;
+/*18*/		u32 right:1;
+/*19*/		u32 left:1;
+/*20*/		u32 sr_l:1;
+/*21*/		u32 sl_l:1;
+/*22*/		u32 l:1;
+/*23*/		u32 zl:1;
+		};
+		u32 buttons;
+	};
+
+	u16 lstick_x;
+	u16 lstick_y;
+	u16 rstick_x;
+	u16 rstick_y;
+	bool center_stick_l;
+	bool center_stick_r;
+	bool conn_l;
+	bool conn_r;
+	bool sio_mode;
+	u8 batt_info_l; // Also Sio Connected status.
+	u8 batt_info_r; // Also Sio IRQ.
+	jc_bt_conn_t bt_conn_l;
+	jc_bt_conn_t bt_conn_r;
+} jc_gamepad_rpt_t;
+
+typedef struct _jc_calib_t
+{
+	u16 x_max:12;
+	u16 y_max:12;
+	u16 x_center:12;
+	u16 y_center:12;
+	u16 x_min:12;
+	u16 y_min:12;
+} __attribute__((packed)) jc_calib_t;
+
+void jc_init_hw();
+void jc_deinit();
+jc_gamepad_rpt_t *joycon_poll();
+jc_gamepad_rpt_t *jc_get_bt_pairing_info(bool *is_l_hos, bool *is_r_hos);
+
+#endif

bdk/input/touch.c

@@ -0,0 +1,461 @@
+/*
+ * Touch driver for Nintendo Switch's STM FingerTip S (4CD60D) touch controller
+ *
+ * Copyright (c) 2018 langerhans
+ * Copyright (c) 2018-2023 CTCaer
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <string.h>
+
+#include <soc/clock.h>
+#include <soc/i2c.h>
+#include <soc/pinmux.h>
+#include <power/max7762x.h>
+#include <soc/gpio.h>
+#include <soc/timer.h>
+#include <soc/t210.h>
+#include <utils/btn.h>
+#include "touch.h"
+
+
+#include <gfx_utils.h>
+#define DPRINTF(...) gfx_printf(__VA_ARGS__)
+
+static touch_panel_info_t _panels[] =
+{
+	{  0,  1, 1, 1,  "NISSHA NFT-K12D" },// 0.
+	{  1,  0, 1, 1,  "GiS GGM6 B2X"    },// 1.
+	{  2,  0, 0, 0,  "NISSHA NBF-K9A"  },// 3.
+	{  3,  1, 0, 0,  "GiS 5.5\""       },// 4.
+	{  4,  0, 0, 1,  "Samsung TSP"     },// 5?
+	{ -1,  1, 0, 1,  "GiS VA 6.2\""    } // 2.
+};
+
+static int touch_command(u8 cmd, u8 *buf, u8 size)
+{
+	int res = i2c_send_buf_small(I2C_3, STMFTS_I2C_ADDR, cmd, buf, size);
+	if (!res)
+		return 1;
+	return 0;
+}
+
+static int touch_read_reg(u8 *cmd, u32 csize, u8 *buf, u32 size)
+{
+	int res = i2c_send_buf_small(I2C_3, STMFTS_I2C_ADDR, cmd[0], &cmd[1], csize - 1);
+	if (res)
+		res = i2c_recv_buf(buf, size, I2C_3, STMFTS_I2C_ADDR);
+	if (!res)
+		return 1;
+
+	return 0;
+}
+
+static int touch_wait_event(u8 event, u8 status, u32 timeout, u8 *buf)
+{
+	u32 timer = get_tmr_ms() + timeout;
+	while (true)
+	{
+		u8 tmp[8] = {0};
+		i2c_recv_buf_small(tmp, 8, I2C_3, STMFTS_I2C_ADDR, STMFTS_READ_ONE_EVENT);
+		if (tmp[1] == event && tmp[2] == status)
+		{
+			if (buf)
+				memcpy(buf, &tmp[3], 5);
+			return 0;
+		}
+
+		if (get_tmr_ms() > timer)
+			return 1;
+	}
+}
+
+#define X_REAL_MAX 1264
+#define Y_REAL_MAX 704
+#define EDGE_OFFSET 15
+
+static void _touch_compensate_limits(touch_event *event, bool touching)
+{
+	event->x  = MAX(event->x, EDGE_OFFSET);
+	event->x  = MIN(event->x, X_REAL_MAX);
+	event->x -= EDGE_OFFSET;
+	u32 x_adj = (1280 * 1000) / (X_REAL_MAX - EDGE_OFFSET);
+	event->x  = ((u32)event->x * x_adj) / 1000;
+
+	if (touching)
+	{
+		event->y  = MAX(event->y, EDGE_OFFSET);
+		event->y  = MIN(event->y, Y_REAL_MAX);
+		event->y -= EDGE_OFFSET;
+		u32 y_adj = (720 * 1000) / (Y_REAL_MAX - EDGE_OFFSET);
+		event->y  = ((u32)event->y * y_adj) / 1000;
+	}
+}
+
+static void _touch_process_contact_event(touch_event *event, bool touching)
+{
+	event->x = (event->raw[2] << 4) | ((event->raw[4] & STMFTS_MASK_Y_LSB) >> 4);
+
+	// Normally, GUI elements have bigger horizontal estate.
+	// Avoid parsing y axis when finger is removed to minimize touch noise.
+	if (touching)
+	{
+		event->y = (event->raw[3] << 4) | (event->raw[4] & STMFTS_MASK_X_MSB);
+
+		event->z = event->raw[5] | (event->raw[6] << 8);
+		event->z = event->z << 6;
+
+		u16 tmp = 0x40;
+		if ((event->raw[7] & 0x3F) != 1 && (event->raw[7] & 0x3F) != 0x3F)
+			tmp = event->raw[7] & 0x3F;
+		event->z /= tmp + 0x40;
+
+		event->fingers = ((event->raw[1] & STMFTS_MASK_TOUCH_ID) >> 4) + 1;
+	}
+	else
+		event->fingers = 0;
+
+	_touch_compensate_limits(event, touching);
+}
+
+static void _touch_parse_event(touch_event *event)
+{
+	event->type = event->raw[1] & STMFTS_MASK_EVENT_ID;
+
+	switch (event->type)
+	{
+	case STMFTS_EV_MULTI_TOUCH_ENTER:
+	case STMFTS_EV_MULTI_TOUCH_MOTION:
+		_touch_process_contact_event(event, true);
+		if (event->z < 255) // Reject palm rest.
+			event->touch = true;
+		else
+		{
+			event->touch = false;
+			event->type = STMFTS_EV_MULTI_TOUCH_LEAVE;
+		}
+		break;
+	case STMFTS_EV_MULTI_TOUCH_LEAVE:
+		event->touch = false;
+		_touch_process_contact_event(event, false);
+		break;
+	case STMFTS_EV_NO_EVENT:
+		if (event->touch)
+			event->type = STMFTS_EV_MULTI_TOUCH_MOTION;
+		break;
+	default:
+		if (event->touch && event->raw[0] == STMFTS_EV_MULTI_TOUCH_MOTION)
+			event->type = STMFTS_EV_MULTI_TOUCH_MOTION;
+		else
+			event->type = STMFTS_EV_MULTI_TOUCH_LEAVE;
+	}
+
+	// gfx_con_setpos(0, 300);
+	// DPRINTF("x = %d    \ny = %d    \nz = %d  \n", event->x, event->y, event->z);
+	// DPRINTF("0 = %02X\n1 = %02X\n2 = %02X\n3 = %02X\n", event->raw[0], event->raw[1], event->raw[2], event->raw[3]);
+	// DPRINTF("4 = %02X\n5 = %02X\n6 = %02X\n7 = %02X\n", event->raw[4], event->raw[5], event->raw[6], event->raw[7]);
+}
+
+void touch_poll(touch_event *event)
+{
+	i2c_recv_buf_small(event->raw, 8, I2C_3, STMFTS_I2C_ADDR, STMFTS_LATEST_EVENT);
+
+	_touch_parse_event(event);
+}
+
+touch_event touch_poll_wait()
+{
+	touch_event event;
+	do
+	{
+		touch_poll(&event);
+	} while (event.type != STMFTS_EV_MULTI_TOUCH_LEAVE);
+
+	return event;
+}
+
+touch_info touch_get_info()
+{
+	touch_info info;
+	u8 buf[8];
+	memset(&buf, 0, 8);
+	i2c_recv_buf_small(buf, 8, I2C_3, STMFTS_I2C_ADDR, STMFTS_READ_INFO);
+
+	info.chip_id = buf[0] << 8 | buf[1];
+	info.fw_ver = buf[2] << 8 | buf[3];
+	info.config_id = buf[4];
+	info.config_ver = buf[5];
+
+	//DPRINTF("ID: %04X, FW Ver: %d.%02d\nCfg ID: %02X, Cfg Ver: %d\n",
+	//	info.chip_id, info.fw_ver >> 8, info.fw_ver & 0xFF, info.config_id, info.config_ver);
+
+	return info;
+}
+
+touch_panel_info_t *touch_get_panel_vendor()
+{
+	u8 buf[5] = {0};
+	u8 cmd = STMFTS_VENDOR_GPIO_STATE;
+	static touch_panel_info_t panel_info = { -2,  0, 0, 0,  ""};
+
+	if (touch_command(STMFTS_VENDOR, &cmd, 1))
+		return NULL;
+
+	if (touch_wait_event(STMFTS_EV_VENDOR, STMFTS_VENDOR_GPIO_STATE, 2000, buf))
+		return NULL;
+
+	for (u32 i = 0; i < ARRAY_SIZE(_panels); i++)
+	{
+		touch_panel_info_t *panel = &_panels[i];
+		if (buf[0] == panel->gpio0 && buf[1] == panel->gpio1 && buf[2] == panel->gpio2)
+			return panel;
+	}
+
+	// Touch panel not found, return current gpios.
+	panel_info.gpio0 = buf[0];
+	panel_info.gpio1 = buf[1];
+	panel_info.gpio2 = buf[2];
+
+	return &panel_info;
+}
+
+int touch_get_fw_info(touch_fw_info_t *fw)
+{
+	u8 buf[8] = {0};
+
+	memset(fw, 0, sizeof(touch_fw_info_t));
+
+	// Get fw address info.
+	u8 cmd[3] = { STMFTS_RW_FRAMEBUFFER_REG, 0, 0x60 };
+	int res = touch_read_reg(cmd, 3, buf, 3);
+	if (!res)
+	{
+		// Get fw info.
+		cmd[1] = buf[2]; cmd[2] = buf[1];
+		res = touch_read_reg(cmd, 3, buf, 8);
+		if (!res)
+		{
+			fw->fw_id   = (buf[1] << 24) | (buf[2] << 16) | (buf[3] << 8) | buf[4];
+			fw->ftb_ver = (buf[6] << 8) | buf[5];
+		}
+
+		cmd[2]++;
+		res = touch_read_reg(cmd, 3, buf, 8);
+		if (!res)
+			fw->fw_rev = (buf[7] << 8) | buf[6];
+	}
+
+	return res;
+}
+
+int touch_sys_reset()
+{
+	u8 cmd[3] = { 0, 0x28, 0x80 }; // System reset cmd.
+	for (u8 retries = 0; retries < 3; retries++)
+	{
+		if (touch_command(STMFTS_WRITE_REG, cmd, 3))
+		{
+			msleep(10);
+			continue;
+		}
+		msleep(10);
+		if (touch_wait_event(STMFTS_EV_CONTROLLER_READY, 0, 20, NULL))
+			continue;
+		else
+			return 0;
+	}
+
+	return 1;
+}
+
+int touch_panel_ito_test(u8 *err)
+{
+	int res = 0;
+
+	// Reset touchscreen module.
+	if (touch_sys_reset())
+		return res;
+
+	// Do ITO Production test.
+	u8 cmd[2] = { 1, 0 };
+	if (touch_command(STMFTS_ITO_CHECK, cmd, 2))
+		return res;
+
+	u32 timer = get_tmr_ms() + 2000;
+	while (true)
+	{
+		u8 tmp[8] = {0};
+		i2c_recv_buf_small(tmp, 8, I2C_3, STMFTS_I2C_ADDR, STMFTS_READ_ONE_EVENT);
+		if (tmp[1] == 0xF && tmp[2] == 0x5)
+		{
+			if (err)
+			{
+				err[0] = tmp[3];
+				err[1] = tmp[4];
+			}
+
+			res = 1;
+			break;
+		}
+
+		if (get_tmr_ms() > timer)
+			break;
+	}
+
+	// Reset touchscreen module.
+	touch_sys_reset();
+
+	return res;
+}
+
+int touch_get_fb_info(u8 *buf)
+{
+	u8 tmp[5];
+
+	u8 cmd[3] = { STMFTS_RW_FRAMEBUFFER_REG, 0, 0 };
+	int res = 0;
+
+
+	for (u32 i = 0; i < 0x10000; i += 4)
+	{
+		if (!res)
+		{
+			cmd[1] = (i >> 8) & 0xFF;
+			cmd[2] = i & 0xFF;
+			memset(tmp, 0xCC, 5);
+			res = touch_read_reg(cmd, 3, tmp, 5);
+			memcpy(&buf[i], tmp + 1, 4);
+		}
+	}
+
+	return res;
+}
+
+int touch_sense_enable()
+{
+	// Switch sense mode and enable multi-touch sensing.
+	u8 cmd = STMFTS_FINGER_MODE;
+	if (touch_command(STMFTS_SWITCH_SENSE_MODE, &cmd, 1))
+		return 0;
+
+	if (touch_command(STMFTS_MS_MT_SENSE_ON, NULL, 0))
+		return 0;
+
+	if (touch_command(STMFTS_CLEAR_EVENT_STACK, NULL, 0))
+		return 0;
+
+	return 1;
+}
+
+int touch_execute_autotune()
+{
+	// Reset touchscreen module.
+	if (touch_sys_reset())
+		return 0;
+
+	// Trim low power oscillator.
+	if (touch_command(STMFTS_LP_TIMER_CALIB, NULL, 0))
+		return 0;
+	msleep(200);
+
+	// Apply Mutual Sense Compensation tuning.
+	if (touch_command(STMFTS_MS_CX_TUNING, NULL, 0))
+		return 0;
+	if (touch_wait_event(STMFTS_EV_STATUS, STMFTS_EV_STATUS_MS_CX_TUNING_DONE, 2000, NULL))
+		return 0;
+
+	// Apply Self Sense Compensation tuning.
+	if (touch_command(STMFTS_SS_CX_TUNING, NULL, 0))
+		return 0;
+	if (touch_wait_event(STMFTS_EV_STATUS, STMFTS_EV_STATUS_SS_CX_TUNING_DONE, 2000, NULL))
+		return 0;
+
+	// Save Compensation data to EEPROM.
+	if (touch_command(STMFTS_SAVE_CX_TUNING, NULL, 0))
+		return 0;
+	if (touch_wait_event(STMFTS_EV_STATUS, STMFTS_EV_STATUS_WRITE_CX_TUNE_DONE, 2000, NULL))
+		return 0;
+
+	return touch_sense_enable();
+}
+
+static int touch_init()
+{
+	// Initialize touchscreen module.
+	if (touch_sys_reset())
+		return 0;
+
+	return touch_sense_enable();
+}
+
+int touch_power_on()
+{
+	// Configure Touscreen and GCAsic shared GPIO.
+	PINMUX_AUX(PINMUX_AUX_CAM_I2C_SDA) = PINMUX_LPDR | PINMUX_INPUT_ENABLE | PINMUX_TRISTATE | PINMUX_PULL_UP | 2;
+	PINMUX_AUX(PINMUX_AUX_CAM_I2C_SCL) = PINMUX_IO_HV | PINMUX_LPDR | PINMUX_TRISTATE | PINMUX_PULL_DOWN | 2; // Unused.
+	gpio_config(GPIO_PORT_S, GPIO_PIN_3, GPIO_MODE_GPIO); // GC detect.
+
+	// Configure touchscreen Touch Reset pin.
+	PINMUX_AUX(PINMUX_AUX_DAP4_SCLK) = PINMUX_PULL_DOWN | 1;
+	gpio_direction_output(GPIO_PORT_J, GPIO_PIN_7, GPIO_LOW);
+	usleep(20);
+
+	// Enable LDO6 for touchscreen AVDD and DVDD supply.
+	max7762x_regulator_set_voltage(REGULATOR_LDO6, 2900000);
+	max7762x_regulator_enable(REGULATOR_LDO6, true);
+
+	// Initialize I2C3.
+	pinmux_config_i2c(I2C_3);
+	clock_enable_i2c(I2C_3);
+	i2c_init(I2C_3);
+	usleep(1000);
+
+	// Set Touch Reset pin.
+	gpio_write(GPIO_PORT_J, GPIO_PIN_7, GPIO_HIGH);
+	usleep(10000);
+
+	// Wait for the touchscreen module to get ready.
+	touch_wait_event(STMFTS_EV_CONTROLLER_READY, 0, 20, NULL);
+
+	// Check for forced boot time calibration.
+	if (btn_read_vol() == (BTN_VOL_UP | BTN_VOL_DOWN))
+	{
+		u8 err[2];
+		if (touch_panel_ito_test(err))
+			if (!err[0] && !err[1])
+				return touch_execute_autotune();
+	}
+
+	// Initialize touchscreen.
+	u32 retries = 3;
+	while (retries)
+	{
+		if (touch_init())
+			return 1;
+		retries--;
+	}
+
+	return 0;
+}
+
+void touch_power_off()
+{
+	// Disable touchscreen power.
+	gpio_write(GPIO_PORT_J, GPIO_PIN_7, GPIO_LOW);
+
+	// Disables LDO6 for touchscreen VDD, AVDD supply
+	max7762x_regulator_enable(REGULATOR_LDO6, false);
+
+	clock_disable_i2c(I2C_3);
+}

bdk/input/touch.h

@@ -1,8 +1,8 @@
 /*
- * Touch driver for Nintendo Switch's STMicroelectronics FingerTip S touch controller
+ * Touch driver for Nintendo Switch's STM FingerTip S (4CD60D) touch controller
  *
  * Copyright (c) 2018 langerhans
- * Copyright (c) 2018 CTCaer
+ * Copyright (c) 2018-2020 CTCaer
  *
  * This program is free software; you can redistribute it and/or modify it
  * under the terms and conditions of the GNU General Public License,
@@ -20,7 +20,7 @@
 #ifndef __TOUCH_H_
 #define __TOUCH_H_
 
-#include "../utils/types.h"
+#include <utils/types.h>
 
 #define STMFTS_I2C_ADDR 0x49
 
@@ -44,20 +44,30 @@
 #define STMFTS_FULL_FORCE_CALIBRATION  0xA2
 #define STMFTS_MS_CX_TUNING            0xA3
 #define STMFTS_SS_CX_TUNING            0xA4
+#define STMFTS_ITO_CHECK               0xA7
 #define STMFTS_RELEASEINFO             0xAA
 #define STMFTS_WRITE_REG               0xB6
+#define STMFTS_SWITCH_SENSE_MODE       0xC3
 #define STMFTS_NOISE_WRITE             0xC7
 #define STMFTS_NOISE_READ              0xC8
-#define STMFTS_RW_FB_REG               0xD0 // read data
+#define STMFTS_RW_FRAMEBUFFER_REG      0xD0
 #define STMFTS_SAVE_CX_TUNING          0xFC
 
-#define STMFTS_UNK0 0xB8 //Request compensation
-#define STMFTS_UNK1 0xCF
-#define STMFTS_UNK2 0xF7
-#define STMFTS_UNK3 0xFA
-#define STMFTS_UNK4 0xF9
+#define STMFTS_DETECTION_CONFIG        0xB0
+#define STMFTS_REQU_COMP_DATA          0xB8
+#define STMFTS_VENDOR                  0xCF
+#define STMFTS_FLASH_UNLOCK            0xF7
+#define STMFTS_FLASH_WRITE_64K         0xF8
+#define STMFTS_FLASH_STATUS            0xF9
+#define STMFTS_FLASH_OP                0xFA
 #define STMFTS_UNK5 0x62
 
+/* cmd parameters */
+#define STMFTS_VENDOR_GPIO_STATE       0x01
+#define STMFTS_VENDOR_SENSE_MODE       0x02
+#define STMFTS_STYLUS_MODE             0x00
+#define STMFTS_FINGER_MODE             0x01
+#define STMFTS_HOVER_MODE              0x02
 
 /* events */
 #define STMFTS_EV_NO_EVENT             0x00
@@ -72,12 +82,16 @@
 #define STMFTS_EV_ERROR                0x0f
 #define STMFTS_EV_NOISE_READ           0x17
 #define STMFTS_EV_NOISE_WRITE          0x18
+#define STMFTS_EV_VENDOR               0x20
 
 #define STMFTS_EV_CONTROLLER_READY     0x10
-#define STMFTS_EV_SLEEP_OUT_CONTROLLER_READY 0x11
 #define STMFTS_EV_STATUS               0x16
 #define STMFTS_EV_DEBUG                0xDB
 
+#define STMFTS_EV_STATUS_MS_CX_TUNING_DONE  1
+#define STMFTS_EV_STATUS_SS_CX_TUNING_DONE  2
+#define STMFTS_EV_STATUS_WRITE_CX_TUNE_DONE 4
+
 /* multi touch related event masks */
 #define STMFTS_MASK_EVENT_ID   0x0F
 #define STMFTS_MASK_TOUCH_ID   0xF0
@@ -95,16 +109,46 @@
 #define STMFTS_DATA_MAX_SIZE (STMFTS_EVENT_SIZE * STMFTS_STACK_DEPTH)
 #define STMFTS_MAX_FINGERS   10
 
+typedef enum _touch_ito_error {
+	ITO_NO_ERROR = 0,
+	ITO_FORCE_OPEN,
+	ITO_SENSE_OPEN,
+	ITO_FORCE_SHRT_GND,
+	ITO_SENSE_SHRT_GND,
+	ITO_FORCE_SHRT_VCM,
+	ITO_SENSE_SHRT_VCM,
+	ITO_FORCE_SHRT_FORCE,
+	ITO_SENSE_SHRT_SENSE,
+	ITO_F2E_SENSE,
+	ITO_FPC_FORCE_OPEN,
+	ITO_FPC_SENSE_OPEN,
+	ITO_KEY_FORCE_OPEN,
+	ITO_KEY_SENSE_OPEN,
+	ITO_RESERVED0,
+	ITO_RESERVED1,
+	ITO_RESERVED2,
+	ITO_MAX_ERR_REACHED = 0xFF
+} touch_ito_error;
+
 typedef struct _touch_event {
 	u8   raw[8];
 	u16  type; // Event type.
 	u16  x;    // Horizontal coordinates.
 	u16  y;    // Vertical coordinates.
-	u8   z;
+	u32  z;
 	u8   fingers;
 	bool touch;
 } touch_event;
 
+typedef struct _touch_panel_info_t
+{
+	u8 idx;
+	u8 gpio0;
+	u8 gpio1;
+	u8 gpio2;
+	char *vendor;
+} touch_panel_info_t;
+
 typedef struct _touch_info {
 	u16 chip_id;
 	u16 fw_ver;
@@ -112,10 +156,21 @@ typedef struct _touch_info {
 	u16 config_ver;
 } touch_info;
 
-int touch_power_on();
-void touch_power_off();
+typedef struct _touch_fw_info_t {
+	u32 fw_id;
+	u16 ftb_ver;
+	u16 fw_rev;
+} touch_fw_info_t;
+
 void touch_poll(touch_event *event);
 touch_event touch_poll_wait();
+touch_panel_info_t *touch_get_panel_vendor();
+int touch_get_fw_info(touch_fw_info_t *fw);
 touch_info touch_get_info();
+int touch_panel_ito_test(u8 *err);
+int touch_execute_autotune();
+int touch_sense_enable();
+int touch_power_on();
+void touch_power_off();
 
 #endif /* __TOUCH_H_ */

bdk/libs/compr/blz.c

@@ -0,0 +1,101 @@
+/*
+ * Copyright (c) 2018 rajkosto
+ * Copyright (c) 2018 SciresM
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <stdlib.h>
+#include <string.h>
+
+#include "blz.h"
+
+const blz_footer *blz_get_footer(const u8 *comp_data, u32 comp_data_size, blz_footer *out_footer)
+{
+	if (comp_data_size < sizeof(blz_footer))
+		return NULL;
+
+	const blz_footer *src_footer = (const blz_footer *)&comp_data[comp_data_size - sizeof(blz_footer)];
+	if (out_footer)
+		memcpy(out_footer, src_footer, sizeof(blz_footer)); // Must be a memcpy because no unaligned accesses on ARMv4.
+
+	return src_footer;
+}
+
+// From https://github.com/SciresM/hactool/blob/master/kip.c which is exactly how kernel does it, thanks SciresM!
+int blz_uncompress_inplace(u8 *data, u32 comp_size, const blz_footer *footer)
+{
+	u32 addl_size = footer->addl_size;
+	u32 header_size = footer->header_size;
+	u32 cmp_and_hdr_size = footer->cmp_and_hdr_size;
+
+	u8 *cmp_start = &data[comp_size] - cmp_and_hdr_size;
+	u32 cmp_ofs = cmp_and_hdr_size - header_size;
+	u32 out_ofs = cmp_and_hdr_size + addl_size;
+
+	while (out_ofs)
+	{
+		u8 control = cmp_start[--cmp_ofs];
+		for (u32 i = 0; i < 8; i++)
+		{
+			if (control & 0x80)
+			{
+				if (cmp_ofs < 2)
+					return 0; // Out of bounds.
+
+				cmp_ofs -= 2;
+				u16 seg_val = ((u32)(cmp_start[cmp_ofs + 1]) << 8) | cmp_start[cmp_ofs];
+				u32 seg_size = ((seg_val >> 12) & 0xF) + 3;
+				u32 seg_ofs = (seg_val & 0x0FFF) + 3;
+
+				// Kernel restricts segment copy to stay in bounds.
+				if (out_ofs < seg_size)
+					seg_size = out_ofs;
+
+				out_ofs -= seg_size;
+
+				for (u32 j = 0; j < seg_size; j++)
+					cmp_start[out_ofs + j] = cmp_start[out_ofs + j + seg_ofs];
+			}
+			else // Copy directly.
+			{
+				if (cmp_ofs < 1)
+					return 0; // Out of bounds.
+
+				cmp_start[--out_ofs] = cmp_start[--cmp_ofs];
+			}
+
+			control <<= 1;
+
+			if (!out_ofs) // Blz works backwards, so if it reaches byte 0, it's done.
+				return 1;
+		}
+	}
+
+	return 1;
+}
+
+int blz_uncompress_srcdest(const u8 *comp_data, u32 comp_data_size, u8 *dst_data, u32 dst_size)
+{
+	blz_footer footer;
+	const blz_footer *comp_footer = blz_get_footer(comp_data, comp_data_size, &footer);
+	if (!comp_footer)
+		return 0;
+
+	// Decompression happens in-place, so need to copy the relevant compressed data first.
+	u32 comp_bytes = (const u8 *)comp_footer - comp_data;
+	memcpy(dst_data, comp_data, comp_bytes);
+	memset(&dst_data[comp_bytes], 0, dst_size - comp_bytes);
+
+	return blz_uncompress_inplace(dst_data, comp_data_size, &footer);
+}

bdk/libs/compr/blz.h

@@ -17,7 +17,7 @@
 #ifndef _BLZ_H_
 #define _BLZ_H_
 
-#include "../../utils/types.h"
+#include <utils/types.h>
 
 typedef struct _blz_footer
 {
@@ -26,11 +26,11 @@ typedef struct _blz_footer
 	u32 addl_size;
 } blz_footer;
 
-// Returns pointer to footer in compData if present, additionally copies it to outFooter if not NULL.
-const blz_footer *blz_get_footer(const unsigned char *compData, unsigned int compDataLen, blz_footer *outFooter);
+// Returns pointer to footer in comp_data if present, additionally copies it to out_footer if not NULL.
+const blz_footer *blz_get_footer(const u8 *comp_data, u32 comp_data_size, blz_footer *out_footer);
 // Returns 0 on failure.
-int blz_uncompress_inplace(unsigned char *dataBuf, unsigned int compSize, const blz_footer *footer);
+int blz_uncompress_inplace(u8 *data, u32 comp_size, const blz_footer *footer);
 // Returns 0 on failure.
-int blz_uncompress_srcdest(const unsigned char *compData, unsigned int compDataLen, unsigned char *dstData, unsigned int dstSize);
+int blz_uncompress_srcdest(const u8 *comp_data, u32 comp_data_size, u8 *dst_data, u32 dst_size);
 
 #endif

bdk/libs/compr/lz.c

@@ -125,7 +125,7 @@ static int _LZ_ReadVarSize( unsigned int * x, const unsigned char * buf )
 *  insize  - Number of input bytes.
 *************************************************************************/
 
-void LZ_Uncompress( const unsigned char *in, unsigned char *out,
+unsigned int LZ_Uncompress( const unsigned char *in, unsigned char *out,
     unsigned int insize )
 {
     unsigned char marker, symbol;
@@ -134,7 +134,7 @@ void LZ_Uncompress( const unsigned char *in, unsigned char *out,
     /* Do we have anything to uncompress? */
     if( insize < 1 )
     {
-        return;
+        return 0;
     }
 
     /* Get marker symbol from input stream */
@@ -176,4 +176,6 @@ void LZ_Uncompress( const unsigned char *in, unsigned char *out,
         }
     }
     while( inpos < insize );
+
+    return outpos;
 }

bdk/libs/compr/lz.h

@@ -41,7 +41,7 @@ extern "C" {
 * Function prototypes
 *************************************************************************/
 
-void LZ_Uncompress( const unsigned char *in, unsigned char *out,
+unsigned int LZ_Uncompress( const unsigned char *in, unsigned char *out,
                     unsigned int insize );
 
 

bdk/libs/compr/lz4.h

@@ -0,0 +1,569 @@
+/*
+ *  LZ4 - Fast LZ compression algorithm
+ *  Header File
+ *  Copyright (C) 2011-2017, Yann Collet.
+
+   BSD 2-Clause License (http://www.opensource.org/licenses/bsd-license.php)
+
+   Redistribution and use in source and binary forms, with or without
+   modification, are permitted provided that the following conditions are
+   met:
+
+       * Redistributions of source code must retain the above copyright
+   notice, this list of conditions and the following disclaimer.
+       * Redistributions in binary form must reproduce the above
+   copyright notice, this list of conditions and the following disclaimer
+   in the documentation and/or other materials provided with the
+   distribution.
+
+   THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+   "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+   LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+   A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+   OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+   SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+   LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+   DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+   THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+   (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+   OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+
+   You can contact the author at :
+    - LZ4 homepage : http://www.lz4.org
+    - LZ4 source repository : https://github.com/lz4/lz4
+*/
+#if defined (__cplusplus)
+extern "C" {
+#endif
+
+#ifndef LZ4_H_2983827168210
+#define LZ4_H_2983827168210
+
+/* --- Dependency --- */
+#include <stddef.h>   /* size_t */
+
+
+/**
+  Introduction
+
+  LZ4 is lossless compression algorithm, providing compression speed at 400 MB/s per core,
+  scalable with multi-cores CPU. It features an extremely fast decoder, with speed in
+  multiple GB/s per core, typically reaching RAM speed limits on multi-core systems.
+
+  The LZ4 compression library provides in-memory compression and decompression functions.
+  Compression can be done in:
+    - a single step (described as Simple Functions)
+    - a single step, reusing a context (described in Advanced Functions)
+    - unbounded multiple steps (described as Streaming compression)
+
+  lz4.h provides block compression functions. It gives full buffer control to user.
+  Decompressing an lz4-compressed block also requires metadata (such as compressed size).
+  Each application is free to encode such metadata in whichever way it wants.
+
+  An additional format, called LZ4 frame specification (doc/lz4_Frame_format.md),
+  take care of encoding standard metadata alongside LZ4-compressed blocks.
+  If your application requires interoperability, it's recommended to use it.
+  A library is provided to take care of it, see lz4frame.h.
+*/
+
+/*^***************************************************************
+*  Export parameters
+*****************************************************************/
+/*
+*  LZ4_DLL_EXPORT :
+*  Enable exporting of functions when building a Windows DLL
+*  LZ4LIB_VISIBILITY :
+*  Control library symbols visibility.
+*/
+#ifndef LZ4LIB_VISIBILITY
+#  if defined(__GNUC__) && (__GNUC__ >= 4)
+#    define LZ4LIB_VISIBILITY __attribute__ ((visibility ("default")))
+#  else
+#    define LZ4LIB_VISIBILITY
+#  endif
+#endif
+#if defined(LZ4_DLL_EXPORT) && (LZ4_DLL_EXPORT==1)
+#  define LZ4LIB_API __declspec(dllexport) LZ4LIB_VISIBILITY
+#elif defined(LZ4_DLL_IMPORT) && (LZ4_DLL_IMPORT==1)
+#  define LZ4LIB_API __declspec(dllimport) LZ4LIB_VISIBILITY /* It isn't required but allows to generate better code, saving a function pointer load from the IAT and an indirect jump.*/
+#else
+#  define LZ4LIB_API LZ4LIB_VISIBILITY
+#endif
+
+/*------   Version   ------*/
+#define LZ4_VERSION_MAJOR    1    /* for breaking interface changes  */
+#define LZ4_VERSION_MINOR    8    /* for new (non-breaking) interface capabilities */
+#define LZ4_VERSION_RELEASE  2    /* for tweaks, bug-fixes, or development */
+
+#define LZ4_VERSION_NUMBER (LZ4_VERSION_MAJOR *100*100 + LZ4_VERSION_MINOR *100 + LZ4_VERSION_RELEASE)
+
+#define LZ4_LIB_VERSION LZ4_VERSION_MAJOR.LZ4_VERSION_MINOR.LZ4_VERSION_RELEASE
+#define LZ4_QUOTE(str) #str
+#define LZ4_EXPAND_AND_QUOTE(str) LZ4_QUOTE(str)
+#define LZ4_VERSION_STRING LZ4_EXPAND_AND_QUOTE(LZ4_LIB_VERSION)
+
+LZ4LIB_API int LZ4_versionNumber (void);  /**< library version number; useful to check dll version */
+LZ4LIB_API const char* LZ4_versionString (void);   /**< library version string; unseful to check dll version */
+
+
+/*-************************************
+*  Tuning parameter
+**************************************/
+/*!
+ * LZ4_MEMORY_USAGE :
+ * Memory usage formula : N->2^N Bytes (examples : 10 -> 1KB; 12 -> 4KB ; 16 -> 64KB; 20 -> 1MB; etc.)
+ * Increasing memory usage improves compression ratio
+ * Reduced memory usage may improve speed, thanks to cache effect
+ * Default value is 14, for 16KB, which nicely fits into Intel x86 L1 cache
+ */
+#ifndef LZ4_MEMORY_USAGE
+# define LZ4_MEMORY_USAGE 14
+#endif
+
+/*-************************************
+*  Simple Functions
+**************************************/
+/*! LZ4_compress_default() :
+    Compresses 'srcSize' bytes from buffer 'src'
+    into already allocated 'dst' buffer of size 'dstCapacity'.
+    Compression is guaranteed to succeed if 'dstCapacity' >= LZ4_compressBound(srcSize).
+    It also runs faster, so it's a recommended setting.
+    If the function cannot compress 'src' into a more limited 'dst' budget,
+    compression stops *immediately*, and the function result is zero.
+    Note : as a consequence, 'dst' content is not valid.
+    Note 2 : This function is protected against buffer overflow scenarios (never writes outside 'dst' buffer, nor read outside 'source' buffer).
+        srcSize : max supported value is LZ4_MAX_INPUT_SIZE.
+        dstCapacity : size of buffer 'dst' (which must be already allocated)
+        return  : the number of bytes written into buffer 'dst' (necessarily <= dstCapacity)
+                  or 0 if compression fails */
+LZ4LIB_API int LZ4_compress_default(const char* src, char* dst, int srcSize, int dstCapacity);
+
+/*! LZ4_decompress_safe() :
+    compressedSize : is the exact complete size of the compressed block.
+    dstCapacity : is the size of destination buffer, which must be already allocated.
+    return : the number of bytes decompressed into destination buffer (necessarily <= dstCapacity)
+             If destination buffer is not large enough, decoding will stop and output an error code (negative value).
+             If the source stream is detected malformed, the function will stop decoding and return a negative result.
+             This function is protected against malicious data packets.
+*/
+LZ4LIB_API int LZ4_decompress_safe (const char* src, char* dst, int compressedSize, int dstCapacity);
+
+
+/*-************************************
+*  Advanced Functions
+**************************************/
+#define LZ4_MAX_INPUT_SIZE        0x7E000000   /* 2 113 929 216 bytes */
+#define LZ4_COMPRESSBOUND(isize)  ((unsigned)(isize) > (unsigned)LZ4_MAX_INPUT_SIZE ? 0 : (isize) + ((isize)/255) + 16)
+
+/*!
+LZ4_compressBound() :
+    Provides the maximum size that LZ4 compression may output in a "worst case" scenario (input data not compressible)
+    This function is primarily useful for memory allocation purposes (destination buffer size).
+    Macro LZ4_COMPRESSBOUND() is also provided for compilation-time evaluation (stack memory allocation for example).
+    Note that LZ4_compress_default() compresses faster when dstCapacity is >= LZ4_compressBound(srcSize)
+        inputSize  : max supported value is LZ4_MAX_INPUT_SIZE
+        return : maximum output size in a "worst case" scenario
+              or 0, if input size is incorrect (too large or negative)
+*/
+LZ4LIB_API int LZ4_compressBound(int inputSize);
+
+/*!
+LZ4_compress_fast() :
+    Same as LZ4_compress_default(), but allows selection of "acceleration" factor.
+    The larger the acceleration value, the faster the algorithm, but also the lesser the compression.
+    It's a trade-off. It can be fine tuned, with each successive value providing roughly +~3% to speed.
+    An acceleration value of "1" is the same as regular LZ4_compress_default()
+    Values <= 0 will be replaced by ACCELERATION_DEFAULT (currently == 1, see lz4.c).
+*/
+LZ4LIB_API int LZ4_compress_fast (const char* src, char* dst, int srcSize, int dstCapacity, int acceleration);
+
+
+/*!
+LZ4_compress_fast_extState() :
+    Same compression function, just using an externally allocated memory space to store compression state.
+    Use LZ4_sizeofState() to know how much memory must be allocated,
+    and allocate it on 8-bytes boundaries (using malloc() typically).
+    Then, provide it as 'void* state' to compression function.
+*/
+LZ4LIB_API int LZ4_sizeofState(void);
+LZ4LIB_API int LZ4_compress_fast_extState (void* state, const char* src, char* dst, int srcSize, int dstCapacity, int acceleration);
+
+
+/*!
+LZ4_compress_destSize() :
+    Reverse the logic : compresses as much data as possible from 'src' buffer
+    into already allocated buffer 'dst' of size 'targetDestSize'.
+    This function either compresses the entire 'src' content into 'dst' if it's large enough,
+    or fill 'dst' buffer completely with as much data as possible from 'src'.
+        *srcSizePtr : will be modified to indicate how many bytes where read from 'src' to fill 'dst'.
+                      New value is necessarily <= old value.
+        return : Nb bytes written into 'dst' (necessarily <= targetDestSize)
+                 or 0 if compression fails
+*/
+LZ4LIB_API int LZ4_compress_destSize (const char* src, char* dst, int* srcSizePtr, int targetDstSize);
+
+
+/*!
+LZ4_decompress_fast() : **unsafe!**
+This function is a bit faster than LZ4_decompress_safe(),
+but doesn't provide any security guarantee.
+    originalSize : is the uncompressed size to regenerate
+                   Destination buffer must be already allocated, and its size must be >= 'originalSize' bytes.
+    return : number of bytes read from source buffer (== compressed size).
+             If the source stream is detected malformed, the function stops decoding and return a negative result.
+    note : This function respects memory boundaries for *properly formed* compressed data.
+           However, it does not provide any protection against malicious input.
+           It also doesn't know 'src' size, and implies it's >= compressed size.
+           Use this function in trusted environment **only**.
+*/
+LZ4LIB_API int LZ4_decompress_fast (const char* src, char* dst, int originalSize);
+
+/*!
+LZ4_decompress_safe_partial() :
+    This function decompress a compressed block of size 'srcSize' at position 'src'
+    into destination buffer 'dst' of size 'dstCapacity'.
+    The function will decompress a minimum of 'targetOutputSize' bytes, and stop after that.
+    However, it's not accurate, and may write more than 'targetOutputSize' (but always <= dstCapacity).
+   @return : the number of bytes decoded in the destination buffer (necessarily <= dstCapacity)
+        Note : this number can also be < targetOutputSize, if compressed block contains less data.
+            Therefore, always control how many bytes were decoded.
+            If source stream is detected malformed, function returns a negative result.
+            This function is protected against malicious data packets.
+*/
+LZ4LIB_API int LZ4_decompress_safe_partial (const char* src, char* dst, int srcSize, int targetOutputSize, int dstCapacity);
+
+
+/*-*********************************************
+*  Streaming Compression Functions
+***********************************************/
+typedef union LZ4_stream_u LZ4_stream_t;  /* incomplete type (defined later) */
+
+/*! LZ4_createStream() and LZ4_freeStream() :
+ *  LZ4_createStream() will allocate and initialize an `LZ4_stream_t` structure.
+ *  LZ4_freeStream() releases its memory.
+ */
+LZ4LIB_API LZ4_stream_t* LZ4_createStream(void);
+LZ4LIB_API int           LZ4_freeStream (LZ4_stream_t* streamPtr);
+
+/*! LZ4_resetStream() :
+ *  An LZ4_stream_t structure can be allocated once and re-used multiple times.
+ *  Use this function to start compressing a new stream.
+ */
+LZ4LIB_API void LZ4_resetStream (LZ4_stream_t* streamPtr);
+
+/*! LZ4_loadDict() :
+ *  Use this function to load a static dictionary into LZ4_stream_t.
+ *  Any previous data will be forgotten, only 'dictionary' will remain in memory.
+ *  Loading a size of 0 is allowed, and is the same as reset.
+ * @return : dictionary size, in bytes (necessarily <= 64 KB)
+ */
+LZ4LIB_API int LZ4_loadDict (LZ4_stream_t* streamPtr, const char* dictionary, int dictSize);
+
+/*! LZ4_compress_fast_continue() :
+ *  Compress 'src' content using data from previously compressed blocks, for better compression ratio.
+ *  'dst' buffer must be already allocated.
+ *  If dstCapacity >= LZ4_compressBound(srcSize), compression is guaranteed to succeed, and runs faster.
+ *
+ *  Important : The previous 64KB of compressed data is assumed to remain present and unmodified in memory!
+ *
+ *  Special 1 : When input is a double-buffer, they can have any size, including < 64 KB.
+ *              Make sure that buffers are separated by at least one byte.
+ *              This way, each block only depends on previous block.
+ *  Special 2 : If input buffer is a ring-buffer, it can have any size, including < 64 KB.
+ *
+ * @return : size of compressed block
+ *           or 0 if there is an error (typically, cannot fit into 'dst').
+ *  After an error, the stream status is invalid, it can only be reset or freed.
+ */
+LZ4LIB_API int LZ4_compress_fast_continue (LZ4_stream_t* streamPtr, const char* src, char* dst, int srcSize, int dstCapacity, int acceleration);
+
+/*! LZ4_saveDict() :
+ *  If last 64KB data cannot be guaranteed to remain available at its current memory location,
+ *  save it into a safer place (char* safeBuffer).
+ *  This is schematically equivalent to a memcpy() followed by LZ4_loadDict(),
+ *  but is much faster, because LZ4_saveDict() doesn't need to rebuild tables.
+ * @return : saved dictionary size in bytes (necessarily <= maxDictSize), or 0 if error.
+ */
+LZ4LIB_API int LZ4_saveDict (LZ4_stream_t* streamPtr, char* safeBuffer, int maxDictSize);
+
+
+/*-**********************************************
+*  Streaming Decompression Functions
+*  Bufferless synchronous API
+************************************************/
+typedef union LZ4_streamDecode_u LZ4_streamDecode_t;   /* incomplete type (defined later) */
+
+/*! LZ4_createStreamDecode() and LZ4_freeStreamDecode() :
+ *  creation / destruction of streaming decompression tracking structure.
+ *  A tracking structure can be re-used multiple times sequentially. */
+LZ4LIB_API LZ4_streamDecode_t* LZ4_createStreamDecode(void);
+LZ4LIB_API int                 LZ4_freeStreamDecode (LZ4_streamDecode_t* LZ4_stream);
+
+/*! LZ4_setStreamDecode() :
+ *  An LZ4_streamDecode_t structure can be allocated once and re-used multiple times.
+ *  Use this function to start decompression of a new stream of blocks.
+ *  A dictionary can optionnally be set. Use NULL or size 0 for a reset order.
+ * @return : 1 if OK, 0 if error
+ */
+LZ4LIB_API int LZ4_setStreamDecode (LZ4_streamDecode_t* LZ4_streamDecode, const char* dictionary, int dictSize);
+
+/*! LZ4_decompress_*_continue() :
+ *  These decoding functions allow decompression of consecutive blocks in "streaming" mode.
+ *  A block is an unsplittable entity, it must be presented entirely to a decompression function.
+ *  Decompression functions only accept one block at a time.
+ *  The last 64KB of previously decoded data *must* remain available and unmodified at the memory position where they were decoded.
+ *  If less than 64KB of data has been decoded all the data must be present.
+ *
+ *  Special : if application sets a ring buffer for decompression, it must respect one of the following conditions :
+ *  - Exactly same size as encoding buffer, with same update rule (block boundaries at same positions)
+ *    In which case, the decoding & encoding ring buffer can have any size, including very small ones ( < 64 KB).
+ *  - Larger than encoding buffer, by a minimum of maxBlockSize more bytes.
+ *    maxBlockSize is implementation dependent. It's the maximum size of any single block.
+ *    In which case, encoding and decoding buffers do not need to be synchronized,
+ *    and encoding ring buffer can have any size, including small ones ( < 64 KB).
+ *  - _At least_ 64 KB + 8 bytes + maxBlockSize.
+ *    In which case, encoding and decoding buffers do not need to be synchronized,
+ *    and encoding ring buffer can have any size, including larger than decoding buffer.
+ *  Whenever these conditions are not possible, save the last 64KB of decoded data into a safe buffer,
+ *  and indicate where it is saved using LZ4_setStreamDecode() before decompressing next block.
+*/
+LZ4LIB_API int LZ4_decompress_safe_continue (LZ4_streamDecode_t* LZ4_streamDecode, const char* src, char* dst, int srcSize, int dstCapacity);
+LZ4LIB_API int LZ4_decompress_fast_continue (LZ4_streamDecode_t* LZ4_streamDecode, const char* src, char* dst, int originalSize);
+
+
+/*! LZ4_decompress_*_usingDict() :
+ *  These decoding functions work the same as
+ *  a combination of LZ4_setStreamDecode() followed by LZ4_decompress_*_continue()
+ *  They are stand-alone, and don't need an LZ4_streamDecode_t structure.
+ */
+LZ4LIB_API int LZ4_decompress_safe_usingDict (const char* src, char* dst, int srcSize, int dstCapcity, const char* dictStart, int dictSize);
+LZ4LIB_API int LZ4_decompress_fast_usingDict (const char* src, char* dst, int originalSize, const char* dictStart, int dictSize);
+
+
+/*^**********************************************
+ * !!!!!!   STATIC LINKING ONLY   !!!!!!
+ ***********************************************/
+
+/*-************************************
+ *  Unstable declarations
+ **************************************
+ * Declarations in this section should be considered unstable.
+ * Use at your own peril, etc., etc.
+ * They may be removed in the future.
+ * Their signatures may change.
+ **************************************/
+
+#ifdef LZ4_STATIC_LINKING_ONLY
+
+/*! LZ4_resetStream_fast() :
+ *  When an LZ4_stream_t is known to be in a internally coherent state,
+ *  it can often be prepared for a new compression with almost no work, only
+ *  sometimes falling back to the full, expensive reset that is always required
+ *  when the stream is in an indeterminate state (i.e., the reset performed by
+ *  LZ4_resetStream()).
+ *
+ *  LZ4_streams are guaranteed to be in a valid state when:
+ *  - returned from LZ4_createStream()
+ *  - reset by LZ4_resetStream()
+ *  - memset(stream, 0, sizeof(LZ4_stream_t))
+ *  - the stream was in a valid state and was reset by LZ4_resetStream_fast()
+ *  - the stream was in a valid state and was then used in any compression call
+ *    that returned success
+ *  - the stream was in an indeterminate state and was used in a compression
+ *    call that fully reset the state (LZ4_compress_fast_extState()) and that
+ *    returned success
+ */
+LZ4LIB_API void LZ4_resetStream_fast (LZ4_stream_t* streamPtr);
+
+/*! LZ4_compress_fast_extState_fastReset() :
+ *  A variant of LZ4_compress_fast_extState().
+ *
+ *  Using this variant avoids an expensive initialization step. It is only safe
+ *  to call if the state buffer is known to be correctly initialized already
+ *  (see above comment on LZ4_resetStream_fast() for a definition of "correctly
+ *  initialized"). From a high level, the difference is that this function
+ *  initializes the provided state with a call to LZ4_resetStream_fast() while
+ *  LZ4_compress_fast_extState() starts with a call to LZ4_resetStream().
+ */
+LZ4LIB_API int LZ4_compress_fast_extState_fastReset (void* state, const char* src, char* dst, int srcSize, int dstCapacity, int acceleration);
+
+/*! LZ4_attach_dictionary() :
+ *  This is an experimental API that allows for the efficient use of a
+ *  static dictionary many times.
+ *
+ *  Rather than re-loading the dictionary buffer into a working context before
+ *  each compression, or copying a pre-loaded dictionary's LZ4_stream_t into a
+ *  working LZ4_stream_t, this function introduces a no-copy setup mechanism,
+ *  in which the working stream references the dictionary stream in-place.
+ *
+ *  Several assumptions are made about the state of the dictionary stream.
+ *  Currently, only streams which have been prepared by LZ4_loadDict() should
+ *  be expected to work.
+ *
+ *  Alternatively, the provided dictionary stream pointer may be NULL, in which
+ *  case any existing dictionary stream is unset.
+ *
+ *  If a dictionary is provided, it replaces any pre-existing stream history.
+ *  The dictionary contents are the only history that can be referenced and
+ *  logically immediately precede the data compressed in the first subsequent
+ *  compression call.
+ *
+ *  The dictionary will only remain attached to the working stream through the
+ *  first compression call, at the end of which it is cleared. The dictionary
+ *  stream (and source buffer) must remain in-place / accessible / unchanged
+ *  through the completion of the first compression call on the stream.
+ */
+LZ4LIB_API void LZ4_attach_dictionary(LZ4_stream_t *working_stream, const LZ4_stream_t *dictionary_stream);
+
+#endif
+
+/*-************************************
+ *  Private definitions
+ **************************************
+ * Do not use these definitions.
+ * They are exposed to allow static allocation of `LZ4_stream_t` and `LZ4_streamDecode_t`.
+ * Using these definitions will expose code to API and/or ABI break in future versions of the library.
+ **************************************/
+#define LZ4_HASHLOG   (LZ4_MEMORY_USAGE-2)
+#define LZ4_HASHTABLESIZE (1 << LZ4_MEMORY_USAGE)
+#define LZ4_HASH_SIZE_U32 (1 << LZ4_HASHLOG)       /* required as macro for static allocation */
+
+#if defined(__cplusplus) || (defined (__STDC_VERSION__) && (__STDC_VERSION__ >= 199901L) /* C99 */)
+#include <stdint.h>
+
+typedef struct LZ4_stream_t_internal LZ4_stream_t_internal;
+struct LZ4_stream_t_internal {
+    uint32_t hashTable[LZ4_HASH_SIZE_U32];
+    uint32_t currentOffset;
+    uint16_t initCheck;
+    uint16_t tableType;
+    const uint8_t* dictionary;
+    const LZ4_stream_t_internal* dictCtx;
+    uint32_t dictSize;
+};
+
+typedef struct {
+    const uint8_t* externalDict;
+    size_t extDictSize;
+    const uint8_t* prefixEnd;
+    size_t prefixSize;
+} LZ4_streamDecode_t_internal;
+
+#else
+
+typedef struct LZ4_stream_t_internal LZ4_stream_t_internal;
+struct LZ4_stream_t_internal {
+    unsigned int hashTable[LZ4_HASH_SIZE_U32];
+    unsigned int currentOffset;
+    unsigned short initCheck;
+    unsigned short tableType;
+    const unsigned char* dictionary;
+    const LZ4_stream_t_internal* dictCtx;
+    unsigned int dictSize;
+};
+
+typedef struct {
+    const unsigned char* externalDict;
+    size_t extDictSize;
+    const unsigned char* prefixEnd;
+    size_t prefixSize;
+} LZ4_streamDecode_t_internal;
+
+#endif
+
+/*!
+ * LZ4_stream_t :
+ * information structure to track an LZ4 stream.
+ * init this structure before first use.
+ * note : only use in association with static linking !
+ *        this definition is not API/ABI safe,
+ *        it may change in a future version !
+ */
+#define LZ4_STREAMSIZE_U64 ((1 << (LZ4_MEMORY_USAGE-3)) + 4)
+#define LZ4_STREAMSIZE     (LZ4_STREAMSIZE_U64 * sizeof(unsigned long long))
+union LZ4_stream_u {
+    unsigned long long table[LZ4_STREAMSIZE_U64];
+    LZ4_stream_t_internal internal_donotuse;
+} ;  /* previously typedef'd to LZ4_stream_t */
+
+
+/*!
+ * LZ4_streamDecode_t :
+ * information structure to track an LZ4 stream during decompression.
+ * init this structure  using LZ4_setStreamDecode (or memset()) before first use
+ * note : only use in association with static linking !
+ *        this definition is not API/ABI safe,
+ *        and may change in a future version !
+ */
+#define LZ4_STREAMDECODESIZE_U64  4
+#define LZ4_STREAMDECODESIZE     (LZ4_STREAMDECODESIZE_U64 * sizeof(unsigned long long))
+union LZ4_streamDecode_u {
+    unsigned long long table[LZ4_STREAMDECODESIZE_U64];
+    LZ4_streamDecode_t_internal internal_donotuse;
+} ;   /* previously typedef'd to LZ4_streamDecode_t */
+
+
+/*-************************************
+*  Obsolete Functions
+**************************************/
+
+/*! Deprecation warnings
+   Should deprecation warnings be a problem,
+   it is generally possible to disable them,
+   typically with -Wno-deprecated-declarations for gcc
+   or _CRT_SECURE_NO_WARNINGS in Visual.
+   Otherwise, it's also possible to define LZ4_DISABLE_DEPRECATE_WARNINGS */
+#ifdef LZ4_DISABLE_DEPRECATE_WARNINGS
+#  define LZ4_DEPRECATED(message)   /* disable deprecation warnings */
+#else
+#  define LZ4_GCC_VERSION (__GNUC__ * 100 + __GNUC_MINOR__)
+#  if defined (__cplusplus) && (__cplusplus >= 201402) /* C++14 or greater */
+#    define LZ4_DEPRECATED(message) [[deprecated(message)]]
+#  elif (LZ4_GCC_VERSION >= 405) || defined(__clang__)
+#    define LZ4_DEPRECATED(message) __attribute__((deprecated(message)))
+#  elif (LZ4_GCC_VERSION >= 301)
+#    define LZ4_DEPRECATED(message) __attribute__((deprecated))
+#  elif defined(_MSC_VER)
+#    define LZ4_DEPRECATED(message) __declspec(deprecated(message))
+#  else
+#    pragma message("WARNING: You need to implement LZ4_DEPRECATED for this compiler")
+#    define LZ4_DEPRECATED(message)
+#  endif
+#endif /* LZ4_DISABLE_DEPRECATE_WARNINGS */
+
+/* Obsolete compression functions */
+LZ4_DEPRECATED("use LZ4_compress_default() instead") LZ4LIB_API int LZ4_compress               (const char* source, char* dest, int sourceSize);
+LZ4_DEPRECATED("use LZ4_compress_default() instead") LZ4LIB_API int LZ4_compress_limitedOutput (const char* source, char* dest, int sourceSize, int maxOutputSize);
+LZ4_DEPRECATED("use LZ4_compress_fast_extState() instead") LZ4LIB_API int LZ4_compress_withState               (void* state, const char* source, char* dest, int inputSize);
+LZ4_DEPRECATED("use LZ4_compress_fast_extState() instead") LZ4LIB_API int LZ4_compress_limitedOutput_withState (void* state, const char* source, char* dest, int inputSize, int maxOutputSize);
+LZ4_DEPRECATED("use LZ4_compress_fast_continue() instead") LZ4LIB_API int LZ4_compress_continue                (LZ4_stream_t* LZ4_streamPtr, const char* source, char* dest, int inputSize);
+LZ4_DEPRECATED("use LZ4_compress_fast_continue() instead") LZ4LIB_API int LZ4_compress_limitedOutput_continue  (LZ4_stream_t* LZ4_streamPtr, const char* source, char* dest, int inputSize, int maxOutputSize);
+
+/* Obsolete decompression functions */
+LZ4_DEPRECATED("use LZ4_decompress_fast() instead") LZ4LIB_API int LZ4_uncompress (const char* source, char* dest, int outputSize);
+LZ4_DEPRECATED("use LZ4_decompress_safe() instead") LZ4LIB_API int LZ4_uncompress_unknownOutputSize (const char* source, char* dest, int isize, int maxOutputSize);
+
+/* Obsolete streaming functions; degraded functionality; do not use!
+ *
+ * In order to perform streaming compression, these functions depended on data
+ * that is no longer tracked in the state. They have been preserved as well as
+ * possible: using them will still produce a correct output. However, they don't
+ * actually retain any history between compression calls. The compression ratio
+ * achieved will therefore be no better than compressing each chunk
+ * independently.
+ */
+LZ4_DEPRECATED("Use LZ4_createStream() instead") LZ4LIB_API void* LZ4_create (char* inputBuffer);
+LZ4_DEPRECATED("Use LZ4_createStream() instead") LZ4LIB_API int   LZ4_sizeofStreamState(void);
+LZ4_DEPRECATED("Use LZ4_resetStream() instead") LZ4LIB_API  int   LZ4_resetStreamState(void* state, char* inputBuffer);
+LZ4_DEPRECATED("Use LZ4_saveDict() instead") LZ4LIB_API     char* LZ4_slideInputBuffer (void* state);
+
+/* Obsolete streaming decoding functions */
+LZ4_DEPRECATED("use LZ4_decompress_safe_usingDict() instead") LZ4LIB_API int LZ4_decompress_safe_withPrefix64k (const char* src, char* dst, int compressedSize, int maxDstSize);
+LZ4_DEPRECATED("use LZ4_decompress_fast_usingDict() instead") LZ4LIB_API int LZ4_decompress_fast_withPrefix64k (const char* src, char* dst, int originalSize);
+
+#endif /* LZ4_H_2983827168210 */
+
+
+#if defined (__cplusplus)
+}
+#endif

bdk/libs/fatfs/diskio.h

@@ -9,7 +9,7 @@
 extern "C" {
 #endif
 
-#include "../../utils/types.h"
+#include <utils/types.h>
 
 /* Status of Disk Functions */
 typedef BYTE	DSTATUS;
@@ -23,6 +23,14 @@ typedef enum {
 	RES_PARERR		/* 4: Invalid Parameter */
 } DRESULT;
 
+typedef enum {
+	DRIVE_SD   = 0,
+	DRIVE_RAM  = 1,
+	DRIVE_EMMC = 2,
+	DRIVE_BIS  = 3,
+	DRIVE_EMU  = 4
+} DDRIVE;
+
 
 /*---------------------------------------*/
 /* Prototypes for disk control functions */
@@ -33,6 +41,7 @@ DSTATUS disk_status (BYTE pdrv);
 DRESULT disk_read (BYTE pdrv, BYTE* buff, DWORD sector, UINT count);
 DRESULT disk_write (BYTE pdrv, const BYTE* buff, DWORD sector, UINT count);
 DRESULT disk_ioctl (BYTE pdrv, BYTE cmd, void* buff);
+DRESULT disk_set_info (BYTE pdrv, BYTE cmd, void *buff);
 
 
 /* Disk Status Bits (DSTATUS) */
@@ -47,9 +56,11 @@ DRESULT disk_ioctl (BYTE pdrv, BYTE cmd, void* buff);
 /* Generic command (Used by FatFs) */
 #define CTRL_SYNC			0	/* Complete pending write process (needed at FF_FS_READONLY == 0) */
 #define GET_SECTOR_COUNT	1	/* Get media size (needed at FF_USE_MKFS == 1) */
+#define SET_SECTOR_COUNT	1	/* Set media size (needed at FF_USE_MKFS == 1) */
 #define GET_SECTOR_SIZE		2	/* Get sector size (needed at FF_MAX_SS != FF_MIN_SS) */
 #define GET_BLOCK_SIZE		3	/* Get erase block size (needed at FF_USE_MKFS == 1) */
 #define CTRL_TRIM			4	/* Inform device that the data on the block of sectors is no longer used (needed at FF_USE_TRIM == 1) */
+#define SET_SECTOR_OFFSET	5	/* Set media logical offset */
 
 /* Generic command (Not used by FatFs) */
 #define CTRL_POWER			5	/* Get/Set power status */

bdk/libs/fatfs/ff.c

@@ -1,6 +1,6 @@
 /*
  * Copyright (c) 2018 naehrwert
- * Copyright (c) 2018-2019 CTCaer
+ * Copyright (c) 2018-2022 CTCaer
  *
  * This program is free software; you can redistribute it and/or modify it
  * under the terms and conditions of the GNU General Public License,
@@ -38,7 +38,8 @@
 
 #include "ff.h"			/* Declarations of FatFs API */
 #include "diskio.h"		/* Declarations of device I/O functions */
-#include "../../gfx/gfx.h"
+#include <storage/mbr_gpt.h>
+#include <gfx_utils.h>
 
 #define EFSPRINTF(text, ...) print_error(); gfx_printf("%k"text"%k\n", 0xFFFFFF00, 0xFFFFFFFF);
 //#define EFSPRINTF(...)
@@ -3273,7 +3274,6 @@ static FRESULT find_volume (	/* FR_OK(0): successful, !=0: an error occurred */
 		stat = disk_status(fs->pdrv);
 		if (!(stat & STA_NOINIT)) {		/* and the physical drive is kept initialized */
 			if (!FF_FS_READONLY && mode && (stat & STA_PROTECT)) {	/* Check write protection if needed */
-				EFSPRINTF("WPEN1");
 				return FR_WRITE_PROTECTED;
 			}
 			return FR_OK;				/* The filesystem object is valid */
@@ -3284,14 +3284,13 @@ static FRESULT find_volume (	/* FR_OK(0): successful, !=0: an error occurred */
 	/* Following code attempts to mount the volume. (analyze BPB and initialize the filesystem object) */
 
 	fs->fs_type = 0;					/* Clear the filesystem object */
+	fs->part_type = 0;					/* Clear the Partition object */
 	fs->pdrv = LD2PD(vol);				/* Bind the logical drive and a physical drive */
 	stat = disk_initialize(fs->pdrv);	/* Initialize the physical drive */
 	if (stat & STA_NOINIT) { 			/* Check if the initialization succeeded */
-		EFSPRINTF("MDNR");
 		return FR_NOT_READY;			/* Failed to initialize due to no medium or hard error */
 	}
 	if (!FF_FS_READONLY && mode && (stat & STA_PROTECT)) { /* Check disk write protection if needed */
-		EFSPRINTF("WPEN2");
 		return FR_WRITE_PROTECTED;
 	}
 #if FF_MAX_SS != FF_MIN_SS				/* Get sector size (multiple sector size cfg only) */
@@ -3318,6 +3317,20 @@ static FRESULT find_volume (	/* FR_OK(0): successful, !=0: an error occurred */
 		EFSPRINTF("BRNL");
 		return FR_DISK_ERR;		/* An error occured in the disk I/O layer */
 	}
+#if FF_SIMPLE_GPT
+	if (fmt >= 2) {
+		/* If GPT Check the first partition */
+		gpt_header_t *gpt_header = (gpt_header_t *)fs->win;
+		if (move_window(fs, 1) != FR_OK) return FR_DISK_ERR;
+		if (!mem_cmp(&gpt_header->signature, "EFI PART", 8)) {
+			if (move_window(fs, gpt_header->part_ent_lba) != FR_OK) return FR_DISK_ERR;
+			gpt_entry_t *gpt_entry = (gpt_entry_t *)fs->win;
+			fs->part_type = 1;
+			bsect = gpt_entry->lba_start;
+			fmt = bsect ? check_fs(fs, bsect) : 3;	/* Check the partition */
+		}
+	}
+#endif
 	if (fmt >= 2) {
 		EFSPRINTF("NOFAT");
 		return FR_NO_FILESYSTEM;	/* No FAT volume is found */
@@ -3906,11 +3919,11 @@ FRESULT f_read (
 
 
 
-#ifdef FF_FASTFS
+#if FF_FASTFS && FF_USE_FASTSEEK
 /*-----------------------------------------------------------------------*/
 /* Fast Read Aligned Sized File Without a Cache                         */
 /*-----------------------------------------------------------------------*/
-#if FF_USE_FASTSEEK
+
 FRESULT f_read_fast (
 	FIL* fp,			/* Pointer to the file object */
 	const void* buff,	/* Pointer to the data to be written */
@@ -3988,7 +4001,6 @@ FRESULT f_read_fast (
 	LEAVE_FF(fs, FR_OK);
 }
 #endif
-#endif
 
 
 
@@ -4132,11 +4144,11 @@ FRESULT f_write (
 
 
 
-#ifdef FF_FASTFS
+#if FF_FASTFS && FF_USE_FASTSEEK
 /*-----------------------------------------------------------------------*/
 /* Fast Write Aligned Sized File Without a Cache                         */
 /*-----------------------------------------------------------------------*/
-#if FF_USE_FASTSEEK
+
 FRESULT f_write_fast (
 	FIL* fp,			/* Pointer to the file object */
 	const void* buff,	/* Pointer to the data to be written */
@@ -4219,7 +4231,6 @@ FRESULT f_write_fast (
 	LEAVE_FF(fs, FR_OK);
 }
 #endif
-#endif
 
 
 
@@ -4680,8 +4691,7 @@ FRESULT f_lseek (
 
 
 
-#ifdef FF_FASTFS
-#if FF_USE_FASTSEEK
+#if FF_FASTFS && FF_USE_FASTSEEK
 /*-----------------------------------------------------------------------*/
 /* Seek File Read/Write Pointer                                          */
 /*-----------------------------------------------------------------------*/
@@ -4699,16 +4709,15 @@ DWORD *f_expand_cltbl (
 	}
 	if (f_lseek(fp, CREATE_LINKMAP)) {	/* Create cluster link table */
 		ff_memfree(fp->cltbl);
-		fp->cltbl = NULL;
+		fp->cltbl = (void *)0;
 		EFSPRINTF("CLTBLSZ");
-		return NULL;
+		return (void *)0;
 	}
 	f_lseek(fp, 0);
 
 	return fp->cltbl;
 }
 #endif
-#endif
 
 
 
@@ -5842,7 +5851,7 @@ FRESULT f_mkfs (
 	UINT len			/* Size of working buffer [byte] */
 )
 {
-	const UINT n_fats = 1;		/* Number of FATs for FAT/FAT32 volume (1 or 2) */
+	const UINT n_fats = 2;		/* Number of FATs for FAT/FAT32 volume (1 or 2) */
 	const UINT n_rootdir = 512;	/* Number of root directory entries for FAT volume */
 	static const WORD cst[] = {1, 4, 16, 64, 256, 512, 0};	/* Cluster size boundary for FAT volume (4Ks unit) */
 	static const WORD cst32[] = {1, 2, 4, 8, 16, 32, 0};	/* Cluster size boundary for FAT32 volume (128Ks unit) */
@@ -5870,7 +5879,7 @@ FRESULT f_mkfs (
 	stat = disk_initialize(pdrv);
 	if (stat & STA_NOINIT) return FR_NOT_READY;
 	if (stat & STA_PROTECT) return FR_WRITE_PROTECTED;
-	if (disk_ioctl(pdrv, GET_BLOCK_SIZE, &sz_blk) != RES_OK || !sz_blk || sz_blk > 32768 || (sz_blk & (sz_blk - 1))) sz_blk = 1;	/* Erase block to align data area */
+	if (disk_ioctl(pdrv, GET_BLOCK_SIZE, &sz_blk) != RES_OK || !sz_blk || sz_blk > 131072 || (sz_blk & (sz_blk - 1))) sz_blk = 2048;	/* Erase block to align data area. 1MB minimum */
 #if FF_MAX_SS != FF_MIN_SS		/* Get sector size of the medium if variable sector size cfg. */
 	if (disk_ioctl(pdrv, GET_SECTOR_SIZE, &ss) != RES_OK) return FR_DISK_ERR;
 	if (ss > FF_MAX_SS || ss < FF_MIN_SS || (ss & (ss - 1))) return FR_DISK_ERR;
@@ -5906,7 +5915,7 @@ FRESULT f_mkfs (
 	} else {
 		/* Create a single-partition in this function */
 		if (disk_ioctl(pdrv, GET_SECTOR_COUNT, &sz_vol) != RES_OK) LEAVE_MKFS(FR_DISK_ERR);
-		b_vol = (opt & FM_SFD) ? 0 : 63;		/* Volume start sector */
+		b_vol = (opt & FM_SFD) ? 0 : sz_blk;		/* Volume start sector */
 		if (sz_vol < b_vol) LEAVE_MKFS(FR_MKFS_ABORTED);
 		sz_vol -= b_vol;						/* Volume size */
 	}
@@ -6130,6 +6139,9 @@ FRESULT f_mkfs (
 			if (fmt == FS_FAT32) {		/* FAT32: Move FAT base */
 				sz_rsv += n; b_fat += n;
 			} else {					/* FAT: Expand FAT size */
+				if (n % n_fats) {	/* Adjust fractional error if needed */
+					n--; sz_rsv++; b_fat++;
+				}
 				sz_fat += n / n_fats;
 			}
 
@@ -6170,7 +6182,9 @@ FRESULT f_mkfs (
 #endif
 		/* Create FAT VBR */
 		mem_set(buf, 0, ss);
-		mem_cpy(buf + BS_JmpBoot, "\xEB\xFE\x90" "MSDOS5.0", 11);/* Boot jump code (x86), OEM name */
+		/* Boot jump code (x86), OEM name */
+		if (!(opt & FM_PRF2)) mem_cpy(buf + BS_JmpBoot, "\xEB\xFE\x90" "NYX1.0.0", 11);
+		else mem_cpy(buf + BS_JmpBoot, "\xEB\xE9\x90\x00\x00\x00\x00\x00\x00\x00\x00", 11);
 		st_word(buf + BPB_BytsPerSec, ss);				/* Sector size [byte] */
 		buf[BPB_SecPerClus] = (BYTE)pau;				/* Cluster size [sector] */
 		st_word(buf + BPB_RsvdSecCnt, (WORD)sz_rsv);	/* Size of reserved area */
@@ -6183,23 +6197,27 @@ FRESULT f_mkfs (
 		}
 		buf[BPB_Media] = 0xF8;							/* Media descriptor byte */
 		st_word(buf + BPB_SecPerTrk, 63);				/* Number of sectors per track (for int13) */
-		st_word(buf + BPB_NumHeads, 255);				/* Number of heads (for int13) */
+		st_word(buf + BPB_NumHeads, (opt & FM_PRF2) ? 16 : 255);	/* Number of heads (for int13) */
 		st_dword(buf + BPB_HiddSec, b_vol);				/* Volume offset in the physical drive [sector] */
 		if (fmt == FS_FAT32) {
-			st_dword(buf + BS_VolID32, GET_FATTIME());	/* VSN */
+			st_dword(buf + BS_VolID32, (opt & FM_PRF2) ? 0 : GET_FATTIME());	/* VSN */
 			st_dword(buf + BPB_FATSz32, sz_fat);		/* FAT size [sector] */
 			st_dword(buf + BPB_RootClus32, 2);			/* Root directory cluster # (2) */
 			st_word(buf + BPB_FSInfo32, 1);				/* Offset of FSINFO sector (VBR + 1) */
 			st_word(buf + BPB_BkBootSec32, 6);			/* Offset of backup VBR (VBR + 6) */
 			buf[BS_DrvNum32] = 0x80;					/* Drive number (for int13) */
 			buf[BS_BootSig32] = 0x29;					/* Extended boot signature */
-			mem_cpy(buf + BS_VolLab32, "NO NAME    " "FAT32   ", 19);	/* Volume label, FAT signature */
+			/* Volume label, FAT signature */
+			if (!(opt & FM_PRF2)) mem_cpy(buf + BS_VolLab32, FF_MKFS_LABEL "FAT32   ", 19);
+			else mem_cpy(buf + BS_VolLab32, "NO NAME    " "FAT32   ", 19);
 		} else {
 			st_dword(buf + BS_VolID, GET_FATTIME());	/* VSN */
 			st_word(buf + BPB_FATSz16, (WORD)sz_fat);	/* FAT size [sector] */
 			buf[BS_DrvNum] = 0x80;						/* Drive number (for int13) */
 			buf[BS_BootSig] = 0x29;						/* Extended boot signature */
-			mem_cpy(buf + BS_VolLab, "NO NAME    " "FAT     ", 19);	/* Volume label, FAT signature */
+			/* Volume label, FAT signature */
+			if (!(opt & FM_PRF2)) mem_cpy(buf + BS_VolLab, FF_MKFS_LABEL "FAT     ", 19);
+			else mem_cpy(buf + BS_VolLab, "NO NAME    " "FAT     ", 19);
 		}
 		st_word(buf + BS_55AA, 0xAA55);					/* Signature (offset is fixed here regardless of sector size) */
 		if (disk_write(pdrv, buf, b_vol, 1) != RES_OK) LEAVE_MKFS(FR_DISK_ERR);	/* Write it to the VBR sector */
@@ -6210,13 +6228,35 @@ FRESULT f_mkfs (
 			mem_set(buf, 0, ss);
 			st_dword(buf + FSI_LeadSig, 0x41615252);
 			st_dword(buf + FSI_StrucSig, 0x61417272);
-			st_dword(buf + FSI_Free_Count, n_clst - 1);	/* Number of free clusters */
-			st_dword(buf + FSI_Nxt_Free, 2);			/* Last allocated cluster# */
+			if (opt & FM_PRF2) {
+				st_dword(buf + FSI_Free_Count, 0xFFFFFFFF);	/* Invalidate free count */
+				st_dword(buf + FSI_Nxt_Free, 0xFFFFFFFF);	/* Invalidate last allocated cluster */
+			} else {
+				st_dword(buf + FSI_Free_Count, n_clst - 1);	/* Number of free clusters */
+				st_dword(buf + FSI_Nxt_Free, 2);			/* Last allocated cluster# */
+			}
 			st_word(buf + BS_55AA, 0xAA55);
 			disk_write(pdrv, buf, b_vol + 7, 1);		/* Write backup FSINFO (VBR + 7) */
 			disk_write(pdrv, buf, b_vol + 1, 1);		/* Write original FSINFO (VBR + 1) */
 		}
 
+		/* Create PRF2SAFE info */
+		if (fmt == FS_FAT32 && opt & FM_PRF2) {
+			mem_set(buf, 0, ss);
+			st_dword(buf + 0, 0x32465250);				/* Magic PRF2 */
+			st_dword(buf + 4, 0x45464153);				/* Magic SAFE */
+			buf[16] = 0x64;									/* Record type */
+			st_dword(buf + 32, 0x03);						/* Unknown. SYSTEM: 0x3F00. USER: 0x03. Volatile. */
+			if (sz_vol < 0x1000000) {
+				st_dword(buf + 36, 21 + 1);				/* 22 Entries. */
+				st_dword(buf + 508, 0x90BB2F39);			/* Sector CRC32 */
+			} else {
+				st_dword(buf + 36, 21 + 2);				/* 23 Entries. */
+				st_dword(buf + 508, 0x5EA8AFC8);			/* Sector CRC32 */
+			}
+			disk_write(pdrv, buf, b_vol + 3, 1);		/* Write PRF2SAFE info (VBR + 3) */
+		}
+
 		/* Initialize FAT area */
 		mem_set(buf, 0, (UINT)szb_buf);
 		sect = b_fat;		/* FAT start sector */
@@ -6706,6 +6746,8 @@ int f_puts (
 	putbuff pb;
 
 
+	if (str == (void *)0) return EOF; /* String is NULL */
+
 	putc_init(&pb, fp);
 	while (*str) putc_bfd(&pb, *str++);		/* Put the string */
 	return putc_flush(&pb);
@@ -6732,6 +6774,8 @@ int f_printf (
 	TCHAR c, d, str[32], *p;
 
 
+	if (fmt == (void *)0) return EOF; /* String is NULL */
+
 	putc_init(&pb, fp);
 
 	va_start(arp, fmt);

bdk/libs/fatfs/ff.h

@@ -26,8 +26,8 @@
 extern "C" {
 #endif
 
-#include "../../utils/types.h"	/* Basic integer types */
-#include "ffconf.h"		/* FatFs configuration options */
+#include <utils/types.h>	/* Basic integer types */
+#include <fatfs_cfg.h>	/* FatFs configuration options */
 
 #if FF_DEFINED != FFCONF_DEF
 #error Wrong configuration file (ffconf.h).
@@ -95,8 +95,8 @@ typedef DWORD FSIZE_t;
 /* Filesystem object structure (FATFS) */
 
 typedef struct {
-	BYTE	win[FF_MAX_SS];	/* Disk access window for Directory, FAT (and file data at tiny cfg) */
 	BYTE	fs_type;		/* Filesystem type (0:not mounted) */
+	BYTE	part_type;		/* Partition type (0:MBR, 1:GPT) */
 	BYTE	pdrv;			/* Associated physical drive */
 	BYTE	n_fats;			/* Number of FATs (1 or 2) */
 	BYTE	wflag;			/* win[] flag (b0:dirty) */
@@ -138,6 +138,7 @@ typedef struct {
 	DWORD	bitbase;		/* Allocation bitmap base sector */
 #endif
 	DWORD	winsect;		/* Current sector appearing in the win[] */
+	BYTE	win[FF_MAX_SS] __attribute__((aligned(8)));	/* Disk access window for Directory, FAT (and file data at tiny cfg). DMA aligned. */
 } FATFS;
 
 
@@ -168,9 +169,6 @@ typedef struct {
 /* File object structure (FIL) */
 
 typedef struct {
-#if !FF_FS_TINY
-	BYTE	buf[FF_MAX_SS];	/* File private data read/write window */
-#endif
 	FFOBJID	obj;			/* Object identifier (must be the 1st member to detect invalid object pointer) */
 	BYTE	flag;			/* File status flags */
 	BYTE	err;			/* Abort flag (error code) */
@@ -184,6 +182,9 @@ typedef struct {
 #if FF_USE_FASTSEEK
 	DWORD*	cltbl;			/* Pointer to the cluster link map table (nulled on open, set by application) */
 #endif
+#if !FF_FS_TINY
+	BYTE	buf[FF_MAX_SS] __attribute__((aligned(8)));	/* File private data read/write window. DMA aligned. */
+#endif
 } FIL;
 
 
@@ -246,7 +247,7 @@ typedef enum {
 	FR_LOCKED,				/* (16) The operation is rejected according to the file sharing policy */
 	FR_NOT_ENOUGH_CORE,		/* (17) LFN working buffer could not be allocated */
 	FR_TOO_MANY_OPEN_FILES,	/* (18) Number of open files > FF_FS_LOCK */
-#ifdef FF_FASTFS
+#if FF_FASTFS
 	FR_INVALID_PARAMETER,	/* (19) Given parameter is invalid */
 	FR_CLTBL_NO_INIT	    /* (20) The cluster table for fast seek/read/write was not created */
 #else
@@ -263,10 +264,8 @@ FRESULT f_open (FIL* fp, const TCHAR* path, BYTE mode);				/* Open or create a f
 FRESULT f_close (FIL* fp);											/* Close an open file object */
 FRESULT f_read (FIL* fp, void* buff, UINT btr, UINT* br);			/* Read data from the file */
 FRESULT f_write (FIL* fp, const void* buff, UINT btw, UINT* bw);	/* Write data to the file */
-#ifdef FF_FASTFS
 FRESULT f_read_fast (FIL* fp, const void* buff, UINT btr);			/* Fast read data from the file */
 FRESULT f_write_fast (FIL* fp, const void* buff, UINT btw);         /* Fast write data to the file */
-#endif
 FRESULT f_lseek (FIL* fp, FSIZE_t ofs);								/* Move file pointer of the file object */
 FRESULT f_truncate (FIL* fp);										/* Truncate the file */
 FRESULT f_sync (FIL* fp);											/* Flush cached data of the writing file */
@@ -288,9 +287,7 @@ FRESULT f_getfree (const TCHAR* path, DWORD* nclst, FATFS** fatfs);	/* Get numbe
 FRESULT f_getlabel (const TCHAR* path, TCHAR* label, DWORD* vsn);	/* Get volume label */
 FRESULT f_setlabel (const TCHAR* label);							/* Set volume label */
 FRESULT f_forward (FIL* fp, UINT(*func)(const BYTE*,UINT), UINT btf, UINT* bf);	/* Forward data to the stream */
-#ifdef FF_FASTFS
 DWORD  *f_expand_cltbl (FIL* fp, UINT tblsz, FSIZE_t ofs);			/* Expand file and populate cluster table */
-#endif
 FRESULT f_expand (FIL* fp, FSIZE_t fsz, BYTE opt);					/* Allocate a contiguous block to the file */
 FRESULT f_mount (FATFS* fs, const TCHAR* path, BYTE opt);			/* Mount/Unmount a logical drive */
 FRESULT f_mkfs (const TCHAR* path, BYTE opt, DWORD au, void* work, UINT len);	/* Create a FAT volume */
@@ -369,6 +366,7 @@ int ff_del_syncobj (FF_SYNC_t sobj);	/* Delete a sync object */
 #define FM_EXFAT	0x04
 #define FM_ANY		0x07
 #define FM_SFD		0x08
+#define FM_PRF2		0x10
 
 /* Filesystem type (FATFS.fs_type) */
 #define FS_FAT12	1
@@ -380,8 +378,11 @@ int ff_del_syncobj (FF_SYNC_t sobj);	/* Delete a sync object */
 #define	AM_RDO	0x01	/* Read only */
 #define	AM_HID	0x02	/* Hidden */
 #define	AM_SYS	0x04	/* System */
+#define	AM_VOL	0x08	/* Volume */
 #define AM_DIR	0x10	/* Directory */
 #define AM_ARC	0x20	/* Archive */
+#define AM_DEV	0x40	/* Device */
+#define AM_RVD	0x80	/* Reserved */
 
 
 #ifdef __cplusplus

bdk/libs/fatfs/ffsystem.c

@@ -1,14 +1,12 @@
 /*------------------------------------------------------------------------*/
 /* Sample Code of OS Dependent Functions for FatFs                        */
-/* (C) ChaN, 2018                                                          */
-/* (C) CTCaer, 2018                                                       */
+/* (C) ChaN, 2018                                                         */
+/* (C) CTCaer, 2018-2024                                                  */
 /*------------------------------------------------------------------------*/
 
+#include <bdk.h>
 
-#include "ff.h"
-#include "../../mem/heap.h"
-
-
+#include <libs/fatfs/ff.h>
 
 #if FF_USE_LFN == 3	/* Dynamic memory allocation */
 
@@ -20,7 +18,8 @@ void* ff_memalloc (	/* Returns pointer to the allocated memory block (null if no
 	UINT msize		/* Number of bytes to allocate */
 )
 {
-	return malloc(msize);	/* Allocate a new memory block with POSIX API */
+	// Ensure size is aligned to SDMMC block size.
+	return malloc(ALIGN(msize, SDMMC_DAT_BLOCKSIZE));	/* Allocate a new memory block with POSIX API */
 }
 
 
@@ -37,3 +36,22 @@ void ff_memfree (
 
 #endif
 
+#if FF_FS_NORTC == 0
+
+/*------------------------------------------------------------------------*/
+/* Get real time clock                                                    */
+/*------------------------------------------------------------------------*/
+
+DWORD get_fattime (
+	void
+)
+{
+	rtc_time_t time;
+
+	max77620_rtc_get_time_adjusted(&time);
+
+	return (((DWORD)(time.year - 1980) << 25) | ((DWORD)time.month << 21) | ((DWORD)time.day << 16) |
+		((DWORD)time.hour << 11) | ((DWORD)time.min << 5) | (time.sec >> 1));
+}
+
+#endif

bdk/libs/lv_conf.h

@@ -17,8 +17,8 @@
 #ifndef LV_CONF_H
 #define LV_CONF_H
 
-#include "../utils/types.h"
-#include "../../../common/memory_map.h"
+#include <soc/timer.h>
+#include <memory_map.h>
 /*===================
    Dynamic memory
  *===================*/
@@ -32,7 +32,7 @@
 #  define LV_MEM_ADR          NYX_LV_MEM_ADR /*Set an address for memory pool instead of allocation it as an array. Can be in external SRAM too.*/
 #  define LV_MEM_AUTO_DEFRAG  1              /*Automatically defrag on free*/
 #else       /*LV_MEM_CUSTOM*/
-#  define LV_MEM_CUSTOM_INCLUDE "../../../mem/heap.h"   /*Header for the dynamic memory function*/
+#  define LV_MEM_CUSTOM_INCLUDE <mem/heap.h> /*Header for the dynamic memory function*/
 #  define LV_MEM_CUSTOM_ALLOC   malloc       /*Wrapper to malloc*/
 #  define LV_MEM_CUSTOM_FREE    free         /*Wrapper to free*/
 #endif     /*LV_MEM_CUSTOM*/
@@ -147,15 +147,19 @@
 #define LV_COMPILER_VLA_SUPPORTED            1  /* 1: Variable length array is supported*/
 
 /*HAL settings*/
-#define LV_TICK_CUSTOM               1                       /*1: use a custom tick source (removing the need to manually update the tick with `lv_tick_inc`) */
+#define LV_TICK_CUSTOM               1                      /*1: use a custom tick source (removing the need to manually update the tick with `lv_tick_inc`) */
 #if LV_TICK_CUSTOM == 1
-#define LV_TICK_CUSTOM_INCLUDE       "../../../utils/util.h" /*Header for the sys time function*/
-#define LV_TICK_CUSTOM_SYS_TIME_EXPR (get_tmr_ms())          /*Expression evaluating to current systime in ms*/
+#define LV_TICK_CUSTOM_INCLUDE       <soc/timer.h>          /*Header for the sys time function*/
+#define LV_TICK_CUSTOM_SYS_TIME_EXPR ((u32)get_tmr_ms())         /*Expression evaluating to current systime in ms*/
 #endif     /*LV_TICK_CUSTOM*/
 
 
 /*Log settings*/
-#define USE_LV_LOG        0   /*Enable/disable the log module*/
+#ifdef DEBUG_UART_LV_LOG
+#  define USE_LV_LOG        1   /*Enable/disable the log module*/
+#else
+#  define USE_LV_LOG        0   /*Enable/disable the log module*/
+#endif
 #if USE_LV_LOG
 /* How important log should be added:
  * LV_LOG_LEVEL_TRACE       A lot of logs to give detailed information
@@ -163,7 +167,7 @@
  * LV_LOG_LEVEL_WARN        Log if something unwanted happened but didn't caused problem
  * LV_LOG_LEVEL_ERROR       Only critical issue, when the system may fail
  */
-#  define LV_LOG_LEVEL    LV_LOG_LEVEL_ERROR
+#  define LV_LOG_LEVEL    LV_LOG_LEVEL_WARN
 /* 1: Print the log with 'printf'; 0: user need to register a callback*/
 #  define LV_LOG_PRINTF   1
 #endif  /*USE_LV_LOG*/
@@ -292,6 +296,9 @@
 
 /*Message box (dependencies: lv_rect, lv_btnm, lv_label)*/
 #define USE_LV_MBOX     1
+#if USE_LV_MBOX != 0
+#  define LV_MBOX_CLOSE_ANIM_TIME 200     /*ms*/
+#endif
 
 /*Text area (dependencies: lv_label, lv_page)*/
 #define USE_LV_TA       1

bdk/libs/lvgl/lv_core/lv_group.c

@@ -546,8 +546,8 @@ static void obj_to_foreground(lv_obj_t * obj)
         /*Move the last_top object to the foreground*/
         lv_obj_t * par = lv_obj_get_parent(last_top);
         /*After list change it will be the new head*/
-        lv_ll_chg_list(&par->child_ll, &par->child_ll, last_top);
-        lv_obj_invalidate(last_top);
+        if (lv_ll_chg_list(&par->child_ll, &par->child_ll, last_top))
+            lv_obj_invalidate(last_top); /*Only invalidate if not top*/
     }
 }
 

bdk/libs/lvgl/lv_core/lv_indev.c

@@ -357,7 +357,10 @@ static void indev_pointer_proc(lv_indev_t * i, lv_indev_data_t * data)
     if(i->cursor != NULL &&
             (i->proc.last_point.x != data->point.x ||
              i->proc.last_point.y != data->point.y)) {
-        lv_obj_set_pos(i->cursor, data->point.x, data->point.y);
+        /*Use cursor's center as pointer*/
+        uint32_t off_x = lv_obj_get_width(i->cursor) >> 1;
+        uint32_t off_y = lv_obj_get_height(i->cursor) >> 1;
+        lv_obj_set_pos(i->cursor, data->point.x - off_x, data->point.y - off_y);
     }
 
     i->proc.act_point.x = data->point.x;
@@ -643,8 +646,8 @@ static void indev_proc_press(lv_indev_proc_t * proc)
                 /*Move the last_top object to the foreground*/
                 lv_obj_t * par = lv_obj_get_parent(last_top);
                 /*After list change it will be the new head*/
-                lv_ll_chg_list(&par->child_ll, &par->child_ll, last_top);
-                lv_obj_invalidate(last_top);
+                if (lv_ll_chg_list(&par->child_ll, &par->child_ll, last_top))
+                    lv_obj_invalidate(last_top); /*Only invalidate if not top*/
             }
 
             /*Send a signal about the press*/

bdk/libs/lvgl/lv_fonts/hekate_symbol_120.c

@@ -16,7 +16,7 @@
 
 #include "../lv_misc/lv_font.h"
 
-#include "../../../../../common/memory_map.h"
+#include <memory_map.h>
 
 #if USE_HEKATE_SYMBOL_120 != 0	/*Can be enabled in lv_conf.h*/
 

bdk/libs/lvgl/lv_fonts/hekate_symbol_20.c

@@ -16,7 +16,7 @@
 
 #include "../lv_misc/lv_font.h"
 
-#include "../../../../../common/memory_map.h"
+#include <memory_map.h>
 
 #if USE_HEKATE_SYMBOL_20 != 0	/*Can be enabled in lv_conf.h*/
 

bdk/libs/lvgl/lv_fonts/hekate_symbol_30.c

@@ -16,7 +16,7 @@
 
 #include "../lv_misc/lv_font.h"
 
-#include "../../../../../common/memory_map.h"
+#include <memory_map.h>
 
 #if USE_HEKATE_SYMBOL_30 != 0	/*Can be enabled in lv_conf.h*/
 

bdk/libs/lvgl/lv_fonts/interui_20.c

@@ -16,7 +16,7 @@
 
 #include "../lv_misc/lv_font.h"
 
-#include "../../../../../common/memory_map.h"
+#include <memory_map.h>
 
 #if USE_INTERUI_20 != 0	/*Can be enabled in lv_conf.h*/
 

bdk/libs/lvgl/lv_fonts/interui_30.c

@@ -16,7 +16,7 @@
 
 #include "../lv_misc/lv_font.h"
 
-#include "../../../../../common/memory_map.h"
+#include <memory_map.h>
 
 #if USE_INTERUI_30 != 0	/*Can be enabled in lv_conf.h*/
 

bdk/libs/lvgl/lv_fonts/ubuntu_mono.c

@@ -16,7 +16,7 @@
 
 #include "../lv_misc/lv_font.h"
 
-#include "../../../../../common/memory_map.h"
+#include <memory_map.h>
 
 #if USE_UBUNTU_MONO != 0	/*Can be enabled in lv_conf.h*/
 

bdk/libs/lvgl/lv_hal/lv_hal_indev.h

@@ -17,7 +17,7 @@ extern "C" {
  *********************/
 #include <stdint.h>
 #include "lv_hal.h"
-#include "../../../utils/types.h"
+#include <utils/types.h>
 #include "../lv_misc/lv_area.h"
 #include "../lv_core/lv_obj.h"