If no bit-rate is passed, let the server use the default value (8Mbps).
This avoids to define a default value on both sides, and to pass the
default bit-rate as an argument when starting the server.
By default, audio is enabled (--no-audio must be explicitly passed to
disable it).
However, some devices may not support audio capture (typically devices
below Android 11, or Android 11 when the shell application is not
foreground on start).
In that case, make the server notify the client to dynamically disable
audio forwarding so that it does not wait indefinitely for an audio
stream.
Also disable audio on unknown codec or missing decoder on the
client-side, for the same reasons.
For video streams (at least H.264 and H.265), the config packet
containing SPS/PPS must be prepended to the next packet (the following
keyframe).
For audio streams (at least OPUS), they must not be merged.
When audio is enabled, open a new socket to send the audio stream from
the device to the client.
Co-authored-by: Romain Vimont <rom@rom1v.com>
Signed-off-by: Romain Vimont <rom@rom1v.com>
Audio will be enabled by default (when supported). Add an option to
disable it.
Co-authored-by: Romain Vimont <rom@rom1v.com>
Signed-off-by: Romain Vimont <rom@rom1v.com>
The recorder opened the target file from the packet sink open()
callback, called by the demuxer. Only then the recorder thread was
started.
One golden rule for the recorder is to never block the demuxer for I/O,
because it would impact mirroring. This rule is respected on recording
packets, but not for the initial recorder opening.
Therefore, start the recorder thread from sc_recorder_init(), open the
file immediately from the recorder thread, then make it wait for the
stream to start (on packet sink open()).
Now that the recorder can report errors directly (rather than making the
demuxer call fail), it is possible to report file opening error even
before the packet sink is open.
The recorder has two initialization phases: one to initialize the
concrete recorder object, and one to open its packet_sink trait.
Initialize mutex and condvar as part of the object initialization.
If there were several packet_sink traits, the mutex and condvar would
still be initialized only once.
Stop scrcpy on recorder errors.
It was previously indirectly stopped by the demuxer, which failed to
push packets to a recorder in error. Report it directly instead:
- it avoids to wait for the next demuxer call;
- it will allow to open the target file from a separate thread and stop
immediately on any I/O error.
When a call to a packet or frame sink fails, do not log the error on the
caller side: either the "failure" is expected (explicitly stopped) or it
must be logged by the packet or frame sink implementation.
The PTS received from MediaCodec are expressed relative to an arbitrary
clock origin. We consider the PTS of the first frame to be 0, and the
PTS of every other frame is relative to this first PTS (note that the
PTS is only used for recording, it is ignored for mirroring).
For simplicity, this relative PTS was computed on the server-side.
To prepare support for multiple stream (video and audio), send the
packet with its original PTS, and handle the PTS offset on the
client-side (by the recorder).
Since we can't know in advance which stream will produce the first
packet with the lowest PTS (a packet received later on one stream may
have a PTS lower than a packet received earlier on another stream),
computing the PTS on the server-side would require unnecessary waiting.
On click event, only the whole buttons state was passed to the device.
In addition, on ACTION_DOWN and ACTION_UP, pass the button associated to
the action.
Refs #3635 <https://github.com/Genymobile/scrcpy/issues/3635>
Co-authored-by: Romain Vimont <rom@rom1v.com>
Signed-off-by: Romain Vimont <rom@rom1v.com>
For the initial connection between the device and the computer, an adb
tunnel is established (with "adb reverse" or "adb forward").
The device-side of the tunnel is a local socket having the hard-coded
name "scrcpy". This may cause issues when several scrcpy instances are
started in a few seconds for the same device, since they will try to
bind the same name.
To avoid conflicts, make the client generate a random UID, and append
this UID to the local socket name ("scrcpy_01234567").
Use av_packet_ref() to reference the packet without copy.
This also simplifies the logic, by making the "offset" variable and the
memcpy() call local to the if-block.
